Changes in PRI programming.

[zigmo36]

We have a Nortel CS1000M, I forget how to determine the software version. :+)

A Tech at AT&T has suggested that I clean up a caller-ID problem affecting incoming calls, in the following manner: He says to change the PRI config to send "National ISDN" instead of "subscriber" or "local" in the Nature of Number INformation Element field on an outbound PRI call to our providing network.

I've found the route data block for the T-1's in question, and they have NATL set to YES (printed from LD 21). Is this what he's talking about, anybody know?

Thanks for any consideration!

zigmo36

 

[Splic3d]

LD 22 - prt iis for the rls. The clid problem could also be with the RCAP setting of the D channel. Nut you didn't say if it was PRI, but I would assume so if you are expecting clid. Prt your RDB and D channel info and we will take a look. D channel - LD 22 - prt, adan dch (#).

http://www.i3techgroup.com

If its not working, get a bigger hammer!

Avaya/Nortel/NEC/Asterisk/Access Control/CCTV/DSX/Acti/UCx

 

[30n30w]

A Tech at AT&T has suggested that I clean up a caller-ID problem [highlight #FCE94F]affecting incoming calls[/highlight], in the following manner: He says to change the PRI config [highlight #8AE234]to send[/highlight] "National ISDN" instead of "subscriber" or "local" in the Nature of Number INformation Element field on an [highlight #729FCF]outbound PRI call to our providing network[/highlight]."

Can you clarify your question a bit? Are you having trouble on the inbound as you stated first? or the outbound as you stated last?
30n30w

 

[Splic3d]

Sorry, can't read or type either, but 30n30w has you going the right direction. We may need to know info from the D channel messaging.

http://www.i3techgroup.com

If its not working, get a bigger hammer!

Avaya/Nortel/NEC/Asterisk/Access Control/CCTV/DSX/Acti/UCx

 

[KCFLHRC]

You can send local calls to a DMI table and change the call type to National

 

[zigmo36]

Thanks for the input, guys! My software version is 3621, and the release is 5, issue 50 J +.

The problem is with incoming calls showing an extra area code before the number that's calling.

I printed the ADAN DCH info, shown below:

ADAN DCH 10
CTYP MSDL
GRP 0
DNUM 15
PORT 0
DES pri12
USR PRI
DCHL 12
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE ATT
SIDE USR
CNEG 1
RLS ID 36
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO
ADAN DCH 11
CTYP MSDL
GRP 0
DNUM 15
PORT 1
DES pri13
USR PRI
DCHL 13
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE ATT
SIDE USR
CNEG 1
RLS ID 36
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO

Thanks again for your help!

zigmo36

 

[Firebird Scrambler]

Can you print off your RDB please?. Also print off from LD 21 the FTR data I'm wondering if you might have added in a different DAPC table. You should already have a DAPC table of "0", but any other table such as "1" onwards can be assigned to a RDB to show a leading digit on incoming CLID calls.



All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[zigmo36]

TYPE RDB
CUST 00
ROUT 10
DES SMARTTRUNK1
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
MBXR NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 5987
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
INST
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
DRNG NO


PAGE 002

CDR YES
INC YES
LAST NO
QREC YES
OAL YES
AIA YES
OAN YES
OPD NO
CDRX NO
NATL YES
MUS NO
EQAR NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO



TYPE RDB
CUST 00
ROUT 11
DES SMARTTRK2
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
MBXR NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 5988
TCPP NO
PII NO
TARG 01 02 05
CLEN 1
BILN NO
OABS
INST
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
DRNG NO


PAGE 002

CDR YES
INC YES
LAST NO
QREC YES
OAL YES
AIA YES
OAN YES
OPD NO
CDRX NO
NATL YES
MUS NO
EQAR NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO


FTR DATA

TBL
**DAPC**PREFIX TABLE NO: 00 **
UNKN**INTL**NATL**ESPN**LOCL**ELOC**ECDP**
UNKN*
E164* 00 0
PRIV*
E163* 00 0
TELX*
X121*
NATL*

OPT AHD BIND BIXA BLA CFF CFRD
COX CPA CTA DBA DNX DSX
HTU HVD XBL IC1 IDP XLF
IHA ITG FKA LOA LRA MCI
MWUD PVCD REA RND
RTR RTD ROX SBA SYA
TTAD VOBD CWRD HLPD HRLD
CXOD
DGRP 50
IRNG NO
PKND 1
DNDL NO
SPRE 1
PREO 0
BPSS NO
SRCD 4620
EEST NO
EESD NO
TTBL 0
MUS NO
ALDN
RECD NO
PORT 0
STCB NO
MCDC NO
NAUT NO
IDEF NO
MTAR NO
LEND NO
MSCD NO
CPCI NO
CONF_DSP
CNFFIELD NO
CNF_NAME CONF
INTFIELD NO
INT_NAME I
EXTFIELD NO
EXT_NAME E
BSFE NO
ASPCT 010
FXS NO
DFLT_LANG ENG
STS_MSG
MSG01 Please leave message
MSG02 Back to work
MSG03 In a meeting
MSG04 On a conference call
MSG05 At lunch
MSG06 Busy call
MSG07 Out of the office today
MSG08 On a business trip
MSG09 Project deadline today
MSG10 Will reply after
VO_ALO NO
PCA OFF
TPDN
BFS_CFW YES
VO_CUR_ZONE_ZDM NO


PAGE 002

VO_CUR_ZONE_TD NO


Thanks again, zigmo36

 

[Firebird Scrambler]

Thanks for that. The DAPC table isn't the problem as only the default is shown in the printout. My guess is that you might need to look at the RCAP settings as I could only see "COLP" present. I'm not sure if you need to add in extra data such as "NDI" etc.

One of my old customers had a QSIG link to a Cisco switch with CLID problems and I ended up adding a bunch of prompts such as.. RCAP NCT MWI COLP NDI CCBI CCNI PRI DV3I CTI QMWI etc.





All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[KCFLHRC]

Maybe change your CO Type from ATT to STD