Call pilot not responding 1

[bkrike]

Hi,
I have a call pilot 100- R1.5 connected to MICS 6.1. The call pilot stops responding when not in use for a couple of days (like a weekend). It will not answer calls, or respond to any feat9**. It will respond only after a reboot.

Tech support says the network connection being plugged in all the time will cause this. I have the problem if it is on the net or not.

Has anyone seen / heard of this (not responding after a couple of days inactivity)…Particularly with hacked call pilots?

 

[bjsvec]

I've heard of plenty of problems with 1.5. you can upgrade to 2.0 with an inexpensive flash card from Nortel. The software is free.

brandon

http://www.teamonesolutions.com

 

[armandel]

hi.

I have the same problem whit a cp150, i rebboted the system and receive this information on serial port, can an y one explain the cause of it.

CallPilot 150 Boot Loader V1.5.19
(C) 2001 Nortel Networks

--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.110.10
LAN interface's subnet mask is 0xffffff00
HARDWARE PARAMETERS:
Serial channels will use a baud rate of 9600
This board's ethernet address is 0:60:38:BE:40:44
CALLPILOT BOOTLOADER PARAMETERS:
Execution Mode: Load CallPilot
Source File System Parameters:
Device: ATA Disk
Source File List Name: filelst.lst
Destination File System Parameters:
Device: ATA Disk
File List Name: filelst.lst
Format Target Device: Y
Boot File Name: CallPilot.bin
After board is reset, start-up code will wait 2 seconds
--------------------------------------------------------------------------
To change any of this, press any key within 2 seconds


Automatic Update Mode Enabled!
To Change Update Mode to Manual, press any key within 10 seconds
Updating in Automatic Mode!

Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SanDisk SDP 5/3 0.6
AtaInit: completed
Done.
Detecting ATA Cards...
Device found in Slot A:
Model: SanDisk SDCFB-192
Serial: 109307C2903E5308
Rev.: Vdi 1.24
Mounted 10.256
Loading 10.256/CallPilot.bin... Done.
Unmounting 10.256
Transferring control to the downloaded code

I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 8 channels
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SanDisk SDP 5/3 0.6
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI...

Standard output device initialized...
7.1\safe not found
Pseudo device initialized...
TFTP device initialized...

Login:

Type "test" to stop auto boot

Curr File Pool Path='7.0\access2\FILEPOOL\0\*.*'
Curr File Pool Path='7.1\access2\FILEPOOL\0\*.*'
OSA DBG: pSOS_ERR: ResumeTask - t_resume rc =15
TCM 1: Channel 0: UP
CH0 is opened.
TCM 2: Channel 2: DOWN
TCM 3: Channel 4: UP
CH4 is opened.
TCM 4: Channel 6: UP
CH6 is opened.
DCHCNTRL - DCH0 Reader created
DCHCNTRL - DCH1 Reader created
DCHCNTRL - DCH2 Reader created
DCHCNTRL - DCH3 Reader created
6arser sync'ed up
DCHCNTRL - Number of D-channels trying :4
4arser sync'ed up
0arser sync'ed up
dchMon: Initialized FumpSTM of Dchannel No : 1
dchMon: Initialized FumpSTM of Dchannel No : 3
dchMon: Initialized FumpSTM of Dchannel No : 4
DCHCNTRL - Active channel = 4 D Channel State = 255

dch: channel 4 Msg Len 99 Update Board to Access

dch: channel 4 Msg Len 99 Update Board to Access

dch: channel 4 Msg Len 99 Update Board to Access
D-channel No. 1 is working
D-channel No. 3 is working
D-channel No. 4 is working
0:receive unknown msg c0
0arser sync'ed up
Got KSU Version from functerm: ----30CQE06H€
Access logging disabled
SYS: Access failed to start, system will restart after 120 seconds
SYS: To stop rebooting, enter stopreboot

 

[bjsvec]

Onr thing I can tell you is that your 2nd port is not coming up. Check for connectivity on the second pair of port A. This should not prevent the CP from coming up though. The error at the end refers to access which is the name of the Nortel VM software- same as NVM and flash, etc.. Sorry that's not much help, but something..

http://www.teamonesolutions.com

 

[bkrike]

My original problem got to the point that the CP100 would stop responding daily. I was told by my supplier that version 1.5.32.01 was bad, and I replaced it with a version 2 unit. No problems now.