BRI Trunk boards 3

[sk1053]

Im trying have added a Bri Trunk board(TN556D) and have set the interface field as 'network' and Country Protocol as '4' for Europe but I'm not sure if this is correct. Does anybody have the correct settings for this screen and also I'm needing to set up a trunk group for this BRI baord and i'm not sure what this settings are. I;ve set up UDP for various extensions to route via AAR to a trunk group but I haven't established what the correct settings are. This setup is to route calls to ISDN fax boards. Canm someone explain how I might do this?

 

[G van Hamburg]

I can explain this to you but thats to much to write down.

Look at the avaya website for proper documentation.

I can give you some tips:

Once you set up the BRI board make sure that the trunks are "in service idle" before you go any further. Your UDP thoughts are OK but this steps comes after the activation of the trunk.

As far as I know the Interface must be user, but if I'm wrong I'm sure somebody will correct me on this.

Ask me if you need more on this.

In holland we have to use "etsi"protocol and the TEI is "auto" Plan your work............Work your plan

 

[vannelle]

Setup for TN556D

display bri-trunk-board a09 print Page 1 of 2
ISDN-BRI TRUNK CIRCUIT PACK
Location: 01A09 Name: So-kaart
Interface Companding: a-law DCP/Analog Bearer Capability: 3.1kHz
Port Interface Side Cntry/Peer TEI Time Invert
Protocol Fill Bits?
1: network etsi auto ones n
2: network etsi auto ones n
3: network etsi auto ones n
4: network etsi auto ones n
5: network etsi auto ones n
6: network etsi auto ones n
7: network etsi auto ones n
8: network etsi auto ones n
9: network etsi auto ones n
10: network etsi auto ones n
11: network etsi auto ones n
12: network etsi auto ones n


display bri-trunk-board a09 print Page 2 of 2
ISDN-BRI TRUNK CIRCUIT PACK
Port XID Endpt SPID Endpt Max
Test? Init? ID NCA TSC
1: n n 0
2: n n 0
3: n n 0
4: n n 0
5: n n 0
6: n n 0
7: n n 0
8: n n 0
9: n n 0
10: n n 0
11: n n 0
12: n n 0

display dialplan print Page 1 of 1
DIAL PLAN RECORD
North American Area Code:
Uniform Dialing Plan: 4-digit
UDP Extension Search Order: local-extensions-first
North American Area Code: Local Node Number:
ETA Node Number:
Uniform Dialing Plan: 4-digit ETA Routing Pattern:
FIRST DIGIT TABLE
First Length
Digit - 1 - - 2 - - 3 - - 4 - - 5 - - 6 -
1: extension
2: extension
3: extension
4: extension
5: extension
7: dac
9: attd
0: dac
*: fac
#: fac



display udp 5000 print Page 1 of 2
UNIFORM DIALING PLAN
Ext Codes: 50dd
Ext Code: 5xxx Type:
Ext Code: 50xx Type:
dd Type dd Type dd Type dd Type dd Type
0x: 1x: 2x: 3x: 4x:
00: UDPCode 001 10: UDPCode 006 20: UDPCode 011 30: 40:
01: UDPCode 001 11: UDPCode 006 21: UDPCode 011 31: 41:
02: UDPCode 002 12: UDPCode 007 22: UDPCode 012 32: 42:
03: UDPCode 002 13: UDPCode 007 23: UDPCode 012 33: 43:
04: UDPCode 003 14: UDPCode 008 24: 34: 44:
05: UDPCode 003 15: UDPCode 008 25: 35: 45:
06: UDPCode 004 16: UDPCode 009 26: 36: 46:
07: UDPCode 004 17: UDPCode 009 27: 37: 47:
08: UDPCode 005 18: UDPCode 010 28: 38: 48:
09: UDPCode 005 19: UDPCode 010 29: 39: 49:



display aar analysis 001 Page 1 of 1
AAR DIGIT ANALYSIS TABLE
Partitioned Group Number: 1 Percent Full: 2
Dialed Total Rte Call Nd ANI Dialed Total Rte Call Nd ANI
String Mn Mx Pat Type Num Rq String Mn Mx Pat Type Num Rq
001 7 7 10 pubu n
002 7 7 11 pubu n
003 7 7 12 pubu n
004 7 7 13 pubu n
005 7 7 14 pubu n
006 7 7 15 pubu n
007 7 7 16 pubu n
008 7 7 17 pubu n
009 7 7 18 pubu n
010 7 7 19 pubu n
011 7 7 20 pubu n
012 7 7 21 pubu n
display route-pattern 10 print Page 1 of 1
Pattern Number: 10
Grp. FRL NPA Pfx Hop Toll No. Del Inserted IXC
No. Mrk Lmt List Digits Digits
1: 10 0 3 user
2: user
3: user
4: user
5: user
6: user
BCC VALUE TSC CA-TSC ITC BCIE Service/Feature Numbering LAR
0 1 2 3 4 W Request Format
1: y y y y y n n unre none
2: y y y y y n n rest none
3: y y y y y n n rest none
4: y y y y y n n rest none
5: y y y y y n n rest none
6: y y y y y n n rest none




display trunk-group 10 print Page 1 of 9
TRUNK GROUP
Group Number: 10 Group Type: isdn CDR Reports: n
Group Name: So-poort 1 COR: 1 TN: 1 TAC: 7010
Direction: two-way Outgoing Display? n
Dial Access? n Busy Threshold: 99 Night Service:
Queue Length: 0
Service Type: tie Auth Code? n TestCall ITC: unre
Far End Test Line No:
TestCall BCC: 4

TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send TCM,Lookahead: 6
Max Message Size to Send: 260
Supplementary Service Protocol: c Digit Handling (in/out): overlap/overlap
Digit Treatment: Digits:
Trunk Hunt: cyclical
Connected to Toll? n STT Loss: normal DTT to DCO Loss: normal
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0


TRUNK FEATURES
ACA Assignment? n Measured: none Wideband Support? n
Internal Alert? n Maintenance Tests? n
Data Restriction? n NCA-TSC Trunk Member:
Send Name: n Send Calling Number: y
Used for DCS? n Send Connected Number: y
Suppress # Outpulsing? n Numbering Format: public
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider
Send UCID? n
Send Codeset 6/7 LAI IE? n


display trunk-group 10 print Page 3 of 9
TRUNK GROUP
Administered Members (min/max): 1/2
GROUP MEMBER ASSIGNMENTS Total Administered Members: 2
Port Code Sfx Name Night Sig Grp
1: 01A0901 TN556 C
2: 01A0917 TN556 C
3:
4:
5:
6:
7:
8:
9:
10:
11:
12:
13:
14:
15:

 

[sk1053]

The screenshots were of great help -thanks

 

[CaNNaBiS]

Can you setup a TN2198 2-wire BRI card as a trunk group as well? I cant figure it out. I tried "add trunk 50" and changed it to type BRI/PRI but when I try to add a port of the BRI card it says it is the wrong type.

What am I missing?

MultiVantage, Intuity Audix LX