Async Dialback not working on 1841 w/WIC-2AM

[Nazgulero]

Hello all,

I am trying to configure async callback on my 1841 with WIC-2AM. The dialin works well, but for some reason, the callback script is not being executed, the debug looks like this:

000079: *Oct 20 11:58:16.335 PCTime: CHAT0/1/0: no matching chat script found for 040284140
000080: *Oct 20 11:58:16.335 PCTime: CHAT0/1/0: Dialing using Modem script: d0efault-d0ials0cript & System script: none
000081: *Oct 20 11:58:16.335 PCTime: CHAT0/1/0: process started
000082: *Oct 20 11:58:16.335 PCTime: CHAT0/1/0: Asserting DTR
000083: *Oct 20 11:58:16.335 PCTime: CHAT0/1/0: Chat script d0efault-d0ials0cript started
000084: *Oct 20 11:59:16.431 PCTime: CHAT0/1/0: Chat script d0efault-d0ials0cript finished, status = Connection timed out; remote h ost not responding

Do you see anything in the config below that might not make sense ? It seems to me that, for some reason, the chat script is not tied to the line/interface...

chat-script callback ABORT ERROR ABORT BUSY "" "ATDT\T" TIMEOUT 60 "CONNECT"\C
!
username test callback-dialstring 040284140 callback-rotary 77 password 7 1403171818557878
!
interface Async0/1/0
description asyn 1/0
ip unnumbered Loopback0
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation ppp
no ip route-cache cef
no ip route-cache
dialer in-band
async mode interactive
peer default ip address pool DIALIN
ppp callback accept
ppp authentication chap pap callin
!
line 0/1/0
script callback callback
login local
modem InOut
modem autoconfigure discovery
rotary 77
transport input all
autoselect during-login
autoselect ppp
stopbits 1
speed 115200
flowcontrol hardware

Thanks for any help in advance.

Regards,

Naz

 

[rtfmdude]

nazgul,

can you try enabling all these debugs and post the results?

debug ppp negotiation
debug modem
debug chat
debug dialer
debug confmodem

Looks like you have a minute between the outdial chat script initiation and the timeout - something's happening there.

 

[COMPUTERTECH33]

I'm having a similar issue. We have a Cisco 1750 and are trying to make the Aux port work for dial out backup.

Here is the config.

Question, can the AUX be configured for dial backup? Or do I have to have a WIC?

mtl01rt01ec#sh run
Building configuration...

Current configuration : 5411 bytes
!
version 12.1
no service single-slot-reload-enable
no service pad
service timestamps debug datetime msec
service timestamps log uptime
service password-encryption
service udp-small-servers
service tcp-small-servers
!
hostname mtl01rt01ec
!
no logging buffered
no logging buffered
logging rate-limit console 10 except errors
no logging console

!

memory-size iomem 20
ip subnet-zero
no ip finger
no ip domain-lookup
ip host test 2005 192.168.48.1
ip dhcp excluded-address 192.168.48.1 192.168.48.20
!
ip dhcp pool Montreal
import all
network 192.168.48.0 255.255.255.0
default-router 192.168.48.1
domain-name berendsen.bfpna.com
dns-server 172.17.2.60 65.118.56.73
netbios-name-server 172.17.2.60 172.17.2.30
netbios-node-type h-node
lease 30
!
ip dhcp pool jdirect1
host 192.168.48.3 255.255.255.0
hardware-address 0030.c18c.0d83
client-name NPI8c0d83
!
ip dhcp pool mtl-wap-wan
host 192.168.48.10 255.255.255.0
hardware-address 0013.1057.ea21
client-name MTLWAP57EA21
!
ip dhcp pool mtl-wap-lan
host 192.168.48.11 255.255.255.0
hardware-address 0013.1057.ea20
client-name MTLWAP57EA20
!
ip dhcp pool MTL-PS1
host 192.168.48.4 255.255.255.0
hardware-address 0013.469c.9766
client-name NPI9C9766
!
no ip bootp server
vpdn enable
no vpdn logging
!
vpdn-group 1
request-dialin
protocol pppoe
!
chat-script modem abort error ""ATDT9,1800\T" TIMEOUT 60 CONNECT \C
modemcap entry usrmodem:MSC=&FS0=1&C1&D3&H1&B1
!
!
crypto isakmp policy 18
hash md5
authentication pre-share
crypto isakmp key B3r3Nd53NfLu1dP0w3R address 65.118.56.35
!
!
crypto ipsec transform-set sharks esp-des esp-md5-hmac
!
crypto map nolan 18 ipsec-isakmp
set peer 65.118.56.35
set transform-set sharks
match address 121
!
!
!
!
interface Loopback0
ip address 172.22.63.5 255.255.255.255
!
interface Loopback1
ip address 172.22.69.254 255.255.255.0
!
interface Ethernet0
description Bell Canadian DSL PPPOE
ip address 70.1.1.2 255.255.255.0
no ip unreachables
ip nat outside
half-duplex
pppoe enable
pppoe-client dial-pool-number 1
no cdp enable
!
interface FastEthernet0
description BFP LAN
ip address 192.168.48.1 255.255.255.0
ip helper-address 172.17.255.255
ip helper-address 172.17.2.30
ip helper-address 172.17.2.255
ip helper-address 172.16.255.255
ip directed-broadcast
ip nat inside
no ip route-cache
no ip mroute-cache
shutdown
speed auto
half-duplex
!
interface Dialer0
no ip address
no cdp enable
!
interface Dialer1
mtu 1492
ip address 69.159.233.85 255.255.255.0
no ip proxy-arp
ip nat outside
encapsulation ppp
no ip route-cache
no ip mroute-cache
dialer pool 1
dialer idle-timeout 0
dialer string 10001
dialer hold-queue 50
dialer-group 1
no peer default ip address
no cdp enable
ppp authentication chap
ppp chap hostname maui-backup
ppp chap password 7 xxxxxxxxxxxxxxxx
ppp chap refuse
ppp pap sent-username xxxxxxxxxxxxxx password xxxxxxxxxxxxxxxxxx
crypto map nolan
hold-queue 224 in
!
router eigrp 100
redistribute static
network 10.0.0.0
network 70.0.0.0
network 172.20.0.0
network 172.21.0.0
network 192.168.40.0
network 192.168.90.0
auto-summary
no eigrp log-neighbor-changes
!
router ospf 1
log-adjacency-changes
network 172.22.0.0 0.0.255.255 area 0
network 192.168.10.0 0.0.0.3 area 0
!
ip nat inside source route-map nonat interface Dialer1 overload
ip kerberos source-interface any
ip classless
no ip forward-protocol udp netbios-ns
no ip forward-protocol udp netbios-dgm
ip forward-protocol udp netbios-ss
ip forward-protocol udp 42508
ip route 0.0.0.0 0.0.0.0 64.1.1.2
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 10.0.0.0 255.0.0.0 51.1.1.1 5
no ip http server
!
logging facility local0
logging 172.17.1.31
access-list 110 deny ip 192.168.48.0 0.0.0.255 172.16.0.0 0.0.255.255
access-list 110 deny ip 192.168.48.0 0.0.0.255 172.17.0.0 0.0.255.255
access-list 110 permit ip 192.168.48.0 0.0.0.255 any
access-list 120 permit ip 192.168.48.0 0.0.0.255 172.16.0.0 0.0.255.255
access-list 120 permit ip 192.168.48.0 0.0.0.255 172.17.0.0 0.0.255.255
access-list 121 permit ip 192.168.48.0 0.0.0.255 172.16.0.0 0.0.255.255
access-list 121 permit ip 192.168.48.0 0.0.0.255 172.17.0.0 0.0.255.255
access-list 150 permit esp host 65.118.56.35 host 0.0.0.0
access-list 150 permit udp host 65.118.56.35 host 0.0.0.0 eq isakmp
access-list 150 permit ip any 192.168.48.0 0.0.0.255
priority-list 1 protocol ip high
dialer-list 1 protocol ip permit
route-map nonat permit 10
match ip address 110
!
snmp-server engineID local 0000000902000001422C57FB
snmp-server community bfpna RO
banner motd ^CCCCCC
Berendsen Fluid Power
Unauthorized access is prohibited
Violators will be prosecuted
Welcome to Montreal
^C
!
line con 0
password 7 xxxxxxxxxxxxxxxxxxx
login
transport input none
line aux 0
exec-timeout 0 0
password 7 xxxxxxxxxxxxxxxxxxxxx
autoselect during-login
autoselect ppp
login local
modem InOut
modem autoconfigure type usrmodem
transport input all
flowcontrol hardware
line vty 0 4
password 7 xxxxxxxxxxxxxxxxxx
login
!
*****************************************************************************************

sh ip route



mtl01rt01ec#sh ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

69.0.0.0/24 is subnetted, 1 subnets
C 69.159.233.0 is directly connected, Dialer1
70.0.0.0/24 is subnetted, 1 subnets
C 70.1.1.0 is directly connected, Ethernet0
172.22.0.0/16 is variably subnetted, 2 subnets, 2 masks
C 172.22.63.5/32 is directly connected, Loopback0
C 172.22.69.0/24 is directly connected, Loopback1
S 10.0.0.0/8 [5/0] via 51.1.1.1
S* 0.0.0.0/0 is directly connected, Dialer1
mtl01rt01ec#

******************************************************************************************
mtl01rt01ec#sh int
Dialer0 is up (spoofing), line protocol is up (spoofing)
Hardware is Unknown
MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
DTR is pulsed for 1 seconds on reset
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
0 packets output, 0 bytes
Dialer1 is up (spoofing), line protocol is up (spoofing)
Hardware is Unknown
Internet address is 69.159.233.85/24
MTU 1492 bytes, BW 56 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
DTR is pulsed for 1 seconds on reset
Last input never, output never, output hang never
Last clearing of "show interface" counters 15:58:09
Input queue: 0/224/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
0 packets output, 0 bytes
Ethernet0 is up, line protocol is up
Hardware is PQUICC Ethernet, address is 0001.64ff.ef80 (bia 0001.64ff.ef80)
Description: Bell Canadian DSL PPPOE
Internet address is 70.1.1.2/24
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 10BaseT
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:03, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 2000 bits/sec, 3 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
109021 packets input, 9247982 bytes, 0 no buffer
Received 109021 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
20012 packets output, 1385968 bytes, 0 underruns(0/0/0)
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
FastEthernet0 is administratively down, line protocol is down
Hardware is PQUICC_FEC, address is 0004.c14e.88c9 (bia 0004.c14e.88c9)
Description: BFP LAN
Internet address is 192.168.48.1/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 15:58:13, output never, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
15 packets input, 920 bytes
Received 15 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns(0/0/0)
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Loopback0 is up, line protocol is up
Hardware is Loopback
Internet address is 172.22.63.5/32
MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation LOOPBACK, loopback not set
Last input 15:35:34, output never, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/0, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
Loopback1 is up, line protocol is up
Hardware is Loopback
Internet address is 172.22.69.254/24
MTU 1514 bytes, BW 8000000 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation LOOPBACK, loopback not set
Last input 15:17:45, output never, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/0, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out

*****************************************************************************************
*Mar 1 16:01:57.024: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
mtl01rt01ec#
16:01:58: %SYS-5-CONFIG_I: Configured from console by console
*Mar 1 16:02:00.140: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:00.140: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:00.140: IP-EIGRP: Neighbor 172.17.1.1 not on common subnet for Ethernet0
*Mar 1 16:02:01.244: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:01.248: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:02.012: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:02:04.400: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:04.400: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:04.692: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:04.692: IP: s=172.17.1.1 (Ethernet0), d=255.255.255.255, len 52, rcvd 2
*Mar 1 16:02:05.544: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:05.548: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:06.888: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:02:09.392: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:09.392: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:10.528: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:10.532: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:10.532: IP-EIGRP: Neighbor 172.17.1.139 not on common subnet for Ethernet0
*Mar 1 16:02:11.868: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:02:14.012: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:14.012: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:15.460: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:15.464: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:16.344: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:02:18.912: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:18.912: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:19.980: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:19.984: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:20.972: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:02:23.320: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:23.320: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:23.320: IP-EIGRP: Neighbor 172.17.1.1 not on common subnet for Ethernet0
*Mar 1 16:02:24.548: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:24.552: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:25.260: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:02:27.808: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:27.808: IP: s=192.168.26.1 (Ethernet0), d=255.255.255.255, len 328, rcvd 2
*Mar 1 16:02:28.040: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:28.040: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:29.156: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:29.160: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:30.060: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:02:31.492: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:31.492: IP: s=172.17.1.1 (Ethernet0), d=255.255.255.255, len 52, rcvd 2
*Mar 1 16:02:32.776: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:32.776: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:33.552: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:33.556: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:33.556: IP-EIGRP: Neighbor 172.17.1.139 not on common subnet for Ethernet0
*Mar 1 16:02:34.432: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:02:37.580: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:37.580: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:38.220: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:38.220: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:38.804: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:02:41.948: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:41.948: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:42.868: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:42.868: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:43.696: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:02:46.580: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:46.580: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:46.580: IP-EIGRP: Neighbor 172.17.1.1 not on common subnet for Ethernet0
*Mar 1 16:02:47.536: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:47.536: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:48.232: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:02:51.328: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:51.328: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:52.128: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:52.128: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:52.488: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:02:55.800: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:55.800: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:56.800: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:02:56.800: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:02:56.800: IP-EIGRP: Neighbor 172.17.1.139 not on common subnet for Ethernet0
*Mar 1 16:02:57.220: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicast
*Mar 1 16:03:00.516: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:03:00.516: IP: s=172.17.1.1 (Ethernet0), d=255.255.255.255, len 52, rcvd 2
*Mar 1 16:03:00.528: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:03:00.528: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:03:01.480: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:03:01.480: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
mtl01rt01ec#
*Mar 1 16:03:02.160: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicastconfig
t
Enter configuration commands, one per line. End with CNTL/Z.
mtl01rt01ec(config)#no l
*Mar 1 16:03:05.320: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:03:05.320: IP: s=172.17.1.1 (Ethernet0), d=224.0.0.10, len 60, rcvd 2
*Mar 1 16:03:06.100: IP: NAT enab = 1 trans = 0 flags = 0
*Mar 1 16:03:06.100: IP: s=172.17.1.139 (Ethernet0), d=224.0.0.10, len 60, rcvd 2oggi
*Mar 1 16:03:06.472: IP: s=70.1.1.2 (local), d=224.0.0.10 (Ethernet0), len 60, sending broad/multicastng console b

thanks

 

[rtfmdude]

Computertech33,

It appears you didn't create the necessary async interface to bind the dialer interface to. Do a 'show line,' and then create the async interface that corresponds to the line, like so:

wads2txg03#sh line
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
0 CTY - - - - - 0 2 0/0 -
97 AUX 9600/9600 - - - - - 0 0 0/0 -
* 98 VTY - - - - - 36 0 0/0 -
99 VTY - - - - - 4 0 0/0 -
100 VTY - - - - - 0 0 0/0 -
101 VTY - - - - - 0 0 0/0 -
102 VTY - - - - - 0 0 0/0 -

Line(s) not in async mode -or- with no hardware support:
1-96

wads2txg03#conf t
Enter configuration commands, one per line. End with CNTL/Z.
wads2txg03(config)#interface async 97
wads2txg03(config-if)# blah blah blah

See how line 97 shows "AUX" when I did the show line? That's how you know which tty corresponds to the aux port. Then, configure per this url:

http://www.cisco.com/warp/public/471/mod-aux-dialout.html