Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

2950-T 24 Port

Status
Not open for further replies.
skialta

skialta

MIS
Joined
Apr 5, 2005
Messages
244
Location
US
How do you reset to the default config on a 2950-T switch? The config I loaded does not seem to work very well and I would like to try the default config. When I reload the config, will it knock all the clients offline? I'd like to not have to do this after-hours. Thanks
 
Sort by date Sort by votes
I just did this yesterday! I added the web gui to make things quicker/easier.

add ip http server and make yourself a username and give correct privilege. From there http into the switch and there is an option to reset to factory default. It will require a reboot, so do this after hours.

Here's also a doc from cisco:

 
Upvote 0 Downvote
I added the ip http server option, but the switch still does not show up on the network. When I ping it, no response. I look at the config and it doesn't have an IP address. I have some 2950G's that I used this same config on with no problem...
Question 1: What do I need to do to get an IP address plugged in and available on the network.
Question 2: After that, I assume that a reset to factory defaults will be an option via the above tip.
 
Upvote 0 Downvote
Okay..I have to amend my above post. I have 3 2950T - 24 switches, but only 1 is available via ping, telnet or http. I reloaded the configs on all 3 switches and the result is the same: only the 1st switch is "pingable". Even if you are plugged into a different switch, only the 1st is "pingable". Below is the config, please advise. Thanks

!
version 12.0
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname TORNIK-Prod2950-01
!
enable secret 5
!
!
!
!
!
!
ip subnet-zero
no ip domain-lookup
!
!
!
interface FastEthernet0/1
spanning-tree portfast
!
interface FastEthernet0/2
spanning-tree portfast
!
interface FastEthernet0/3
spanning-tree portfast
!
interface FastEthernet0/4
spanning-tree portfast
!
interface FastEthernet0/5
spanning-tree portfast
!
interface FastEthernet0/6
spanning-tree portfast
!
interface FastEthernet0/7
spanning-tree portfast
!
interface FastEthernet0/8
spanning-tree portfast
!
interface FastEthernet0/9
spanning-tree portfast
!
interface FastEthernet0/10
spanning-tree portfast
!
interface FastEthernet0/11
spanning-tree portfast
!
interface FastEthernet0/12
spanning-tree portfast
!
interface FastEthernet0/13
spanning-tree portfast
!
interface FastEthernet0/14
spanning-tree portfast
!
interface FastEthernet0/15
spanning-tree portfast
!
interface FastEthernet0/16
spanning-tree portfast
!
interface FastEthernet0/17
spanning-tree portfast
!
interface FastEthernet0/18
spanning-tree portfast
!
interface FastEthernet0/19
spanning-tree portfast
!
interface FastEthernet0/20
spanning-tree portfast
!
interface FastEthernet0/21
spanning-tree portfast
!
interface FastEthernet0/22
spanning-tree portfast
!
interface FastEthernet0/23
spanning-tree portfast
!
interface GigabitEthernet0/1
switchport mode trunk
!
interface GigabitEthernet0/2
switchport mode trunk
!
interface VLAN1
ip address 10.1.1.250 255.255.0.0
no ip directed-broadcast
no ip route-cache
!
ip default-gateway 10.1.1.1
banner login ^C

************************* W A R N I N G *************************

ANY UNAUTHORIZED ACCESS, OR MODIFICATIONS IN ANY FORM IS PROHIBITED.
*************************************************************************
^C
ip http server
!
line con 0
exec-timeout 0 0
transport input none
stopbits 1
line vty 0 4
password
login
line vty 5 15
password
login
!
end
 
Upvote 0 Downvote
The above config...is this the switch you that responds to ping?

Pleae advise
 
Upvote 0 Downvote
Correct, this is the one that responds to ping. The other 2 switches are using the same config with only the IP address and the host name changed. Everything else is the same.
 
Upvote 0 Downvote
would you mind send the config for one that does not respond?
 
Upvote 0 Downvote
Here you go...same, just different IP and host name:


!
version 12.0
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname TORNIK-Prod2950-02
!
enable secret 5
!
!
!
!
!
!
ip subnet-zero
no ip domain-lookup
!
!
!
interface FastEthernet0/1
spanning-tree portfast
!
interface FastEthernet0/2
spanning-tree portfast
!
interface FastEthernet0/3
spanning-tree portfast
!
interface FastEthernet0/4
spanning-tree portfast
!
interface FastEthernet0/5
spanning-tree portfast
!
interface FastEthernet0/6
spanning-tree portfast
!
interface FastEthernet0/7
spanning-tree portfast
!
interface FastEthernet0/8
spanning-tree portfast
!
interface FastEthernet0/9
spanning-tree portfast
!
interface FastEthernet0/10
spanning-tree portfast
!
interface FastEthernet0/11
spanning-tree portfast
!
interface FastEthernet0/12
spanning-tree portfast
!
interface FastEthernet0/13
spanning-tree portfast
!
interface FastEthernet0/14
spanning-tree portfast
!
interface FastEthernet0/15
spanning-tree portfast
!
interface FastEthernet0/16
spanning-tree portfast
!
interface FastEthernet0/17
spanning-tree portfast
!
interface FastEthernet0/18
spanning-tree portfast
!
interface FastEthernet0/19
spanning-tree portfast
!
interface FastEthernet0/20
spanning-tree portfast
!
interface FastEthernet0/21
spanning-tree portfast
!
interface FastEthernet0/22
spanning-tree portfast
!
interface FastEthernet0/23
spanning-tree portfast
!
interface FastEthernet0/24
spanning-tree portfast
!
interface GigabitEthernet0/1
switchport mode trunk
!
interface GigabitEthernet0/2
switchport mode trunk
!
interface VLAN1
ip address 10.1.1.251 255.255.0.0
no ip directed-broadcast
no ip route-cache
!
ip default-gateway 10.1.1.1
banner login ^C

************************* W A R N I N G *************************

ANY UNAUTHORIZED ACCESS, OR MODIFICATIONS IN ANY FORM IS PROHIBITED.
*************************************************************************
^C
ip http server
!
line con 0
exec-timeout 0 0
transport input none
stopbits 1
line vty 0 4
password
login
line vty 5 15
password
login
!
end
 
Upvote 0 Downvote
How are the switches interconnected?
 
Upvote 0 Downvote
Each 2950 is using a Cat 5e cross-over cable going from Gigabit port 1, Switch 1 to Gigabit port 2, Switch 2. Then Gigabit port 1, Switch 2 to Gigabit port 2, Switch 3.

Make sense?

This is the same as I have my 2950G's using the gigastack modules...
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

Zero6
  • Locked
  • Question Question
question about cisco cbs 350-12xs 12 port 10g sfp+
Replies
0
Views
498
Zero6
Zero6
B
  • Locked
  • Question Question
Cisco IP phone 7841 8851 unable to forward all to external number
Replies
0
Views
397
badwolf1686
B
DTGMI
  • Locked
  • Question Question
Moving from Juniper SRX-240 to Cisco ??
Replies
0
Views
346
DTGMI
DTGMI
CPM86
  • Locked
  • Question Question
Cisco isr 4331 with IOS and sip busy fail over to 2nd sip number on pbx?
Replies
0
Views
554
CPM86
CPM86
Gartech
  • Locked
  • Question Question
LAN Port Test Device
Replies
3
Views
461
ipohead
ipohead

Part and Inventory Search

Sponsor

Back
Top