Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations wOOdy-Soft on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

2811 pri not registering with ccm

Status
Not open for further replies.

Burgal

MIS
Jan 3, 2003
246
CA
I have a new deployment of two ccm servers and a 2811 with a vwic 1 port t1 pri card

the router is up, issuing dhcp for phones. CCM is up and calls from endpoint to endpoint are working ok.

The router has given CCM it's ip, and ccm knows about it. the router has been able to go MGCP active and ccm-manager active whilst knowing about the primary and backup ccm servers.

however, ccm hasn't been able to register the pri endpoints. Not sure what's wrong here.

CCM, gateway and phones are all on same vlan. no routing in between them.

running ccm4.1(3)sr3a

here is the sh run:
Current configuration : 3451 bytes
!
version 12.4
service timestamps debug datetime show-timezone
service timestamps log datetime localtime show-timezone
service password-encryption
!
hostname SWRTR-GTWY01
!
boot-start-marker
boot system flash:c2800nm-ipvoicek9-mz.124-8.bin
boot-end-marker
!
logging buffered 51200 warnings
enable password 7 130E1E020005012424
!
no aaa new-model
!
resource policy
!
clock timezone pst -7
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
!
!
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.0.100.1 10.0.100.50
!
ip dhcp pool Science-World
network 10.0.100.0 255.255.255.0
default-router 10.0.100.1
dns-server 198.162.3.1
domain-name sienceworld.ca
option 150 ip 10.0.100.22 10.0.100.21
!
!
no ip domain lookup
ip domain name sienceworld.ca
isdn switch-type primary-ni
!
voice-card 0
dspfarm
dsp services dspfarm
!
!
!
!
!
!
!
!
!
!
!
!
!
!
username admin privilege 15 secret 5 $1$fx.r$ZlHvmW/uW4f0w9CXtYzKu/
!
!
controller T1 0/0/0
framing esf
linecode b8zs
pri-group timeslots 1-24 service mgcp
description ***PRI- to PSTN***
!
!
!
interface FastEthernet0/0
description ***Uplink to Switch***
ip address 10.0.100.10 255.255.255.0
no ip redirects
no ip proxy-arp
ip route-cache flow
no ip mroute-cache
duplex auto
speed auto
h323-gateway voip interface
h323-gateway voip bind srcaddr 10.0.100.10
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable
!
ip route 0.0.0.0 0.0.0.0 10.0.100.1
!
ip http server
no ip http secure-server
!
!
!
!
control-plane
!
!
!
voice-port 0/0/0:23
!
ccm-manager redundant-host 10.0.100.22
ccm-manager mgcp
no ccm-manager fax protocol cisco
ccm-manager music-on-hold
ccm-manager config server 10.0.100.22
ccm-manager config
!
mgcp
mgcp call-agent 10.0.100.21 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
no mgcp package-capability res-package
mgcp package-capability sst-package
no mgcp package-capability fxr-package
mgcp package-capability pre-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
mgcp bind control source-interface FastEthernet0/0
mgcp bind media source-interface FastEthernet0/0
!
mgcp profile default
!
!
!
dial-peer voice 1 pots
description **** T1 PRI Inbound Outbound****
service mgcpapp
port 0/0/0:23
!
banner motd ^CC
********************************************************************
* THIS MACHINE IS THE PROPERTY OF VANCOUVER SCIENCE WORLD. *
* IT IS TO BE USED ONLY FOR AUTHORIZED VANCOUVER SCIENCE WORLD *
* ACTIVITES. UNAUTHORIZED ACCESS OR UNAUTHORIZED USE OF *
* AUTHORIZED ACCESS IS STRICTLY PROHIBITED AND MAY BE PROSECUTED. *
* SCIENCE CENTER RESERVES THE RIGHT TO MONITOR ALL CONNECTIONS. *
********************************************************************
^C
!
line con 0
password 7 000F1A160F520E0800
login
line aux 0
password 7 000F1A160F520E0800
login
line vty 0 4
exec-timeout 60 0
password 7 130E1E020005012424
login
transport input telnet
line vty 5 15
exec-timeout 60 0
password 7 0704285C45001C0B18
login
transport input none
!
scheduler allocate 20000 1000
!
end

Here is the sh mgcp
MGCP Admin State ACTIVE, Oper State ACTIVE - Cause Code NONE
MGCP call-agent: 10.0.100.21 2427 Initial protocol service is MGCP 0.1
MGCP validate call-agent source-ipaddr DISABLED
MGCP validate domain name DISABLED
MGCP block-newcalls DISABLED
MGCP send SGCP RSIP: forced/restart/graceful/disconnected DISABLED
MGCP quarantine mode discard/step
MGCP quarantine of persistent events is ENABLED
MGCP dtmf-relay voip codec all mode out-of-band
MGCP dtmf-relay for voAAL2 is SDP controlled
MGCP voip modem passthrough mode: NSE, codec: g711ulaw, redundancy: DISABLED,
MGCP voaal2 modem passthrough disabled
MGCP voip modem relay: Disabled.
MGCP T.38 Named Signalling Event (NSE) response timer: 200
MGCP Network (IP/AAL2) Continuity Test timer: 200
MGCP 'RTP stream loss' timer disabled
MGCP request timeout 500
MGCP maximum exponential request timeout 4000
MGCP rtp unreachable timeout 1000 action notify
MGCP gateway port: 2427, MGCP maximum waiting delay 3000
MGCP restart delay 0, MGCP vad DISABLED
MGCP rtrcac DISABLED
MGCP system resource check DISABLED
MGCP xpc-codec: DISABLED, MGCP persistent hookflash: DISABLED
MGCP persistent offhook: ENABLED, MGCP persistent onhook: DISABLED
MGCP piggyback msg ENABLED, MGCP endpoint offset DISABLED
MGCP simple-sdp ENABLED
MGCP undotted-notation DISABLED
MGCP codec type g711ulaw, MGCP packetization period 20
MGCP JB threshold lwm 30, MGCP JB threshold hwm 150
MGCP LAT threshold lwm 150, MGCP LAT threshold hwm 300
MGCP PL threshold lwm 1000, MGCP PL threshold hwm 10000
MGCP CL threshold lwm 1000, MGCP CL threshold hwm 10000
MGCP playout mode is adaptive 60, 40, 200 in msec
MGCP Fax Playout Buffer is 300 in msec
MGCP media (RTP) dscp: ef, MGCP signaling dscp: af31
MGCP default package: trunk-package
MGCP supported packages: gm-package dtmf-package trunk-package line-package
hs-package rtp-package atm-package ms-package dt-packa
e
mo-package mt-package sst-package pre-package
MGCP Digit Map matching order: shortest match
SGCP Digit Map matching order: always left-to-right
MGCP VoAAL2 ignore-lco-codec DISABLED
MGCP T.38 Max Fax Rate is DEFAULT
MGCP T.38 Fax is DISABLED
MGCP T.38 Fax ECM is ENABLED
MGCP T.38 Fax NSF Override is DISABLED
MGCP T.38 Fax Low Speed Redundancy: 0
MGCP T.38 Fax High Speed Redundancy: 0
MGCP control bound to interface FastEthernet0/0
MGCP media bound to interface FastEthernet0/0
MGCP Upspeed payload type for G711ulaw: 0, G711alaw: 8
MGCP Static payload type for G.726-16K codec
MGCP Dynamic payload type for G.726-24K codec
MGCP Dynamic payload type for G.Clear codec
MGCP Dynamic payload type for NSE is 100
MGCP Dynamic payload type for NTE is 99
MGCP Guaranteed scheduler time is disabled

and here is the ccm-manager
MGCP Domain Name: SWRTR-GTWY01.sienceworld.ca
Priority Status Host
============================================================
Primary Registered 10.0.100.21
First Backup Backup Ready 10.0.100.22
Second Backup None

Current active Call Manager: 10.0.100.21
Backhaul/Redundant link port: 2428
Failover Interval: 30 seconds
Keepalive Interval: 15 seconds
Last keepalive sent: 18:06:04 pst Jul 31 2006 (elapsed time: 00:00:00
)
Last MGCP traffic time: 18:06:04 pst Jul 31 2006 (elapsed time: 00:00:00
)
Last failover time: 17:54:04 pst Jul 31 2006 from (10.0.100.21)
Last switchback time: 17:54:49 pst Jul 31 2006 from (10.0.100.22)
Switchback mode: Graceful
MGCP Fallback mode: Not Selected
Last MGCP Fallback start time: None
Last MGCP Fallback end time: None
MGCP Download Tones: Disabled

Backhaul Link info:
Link Protocol: TCP
Remote Port Number: 2428
Remote IP Address: 10.0.100.21
Current Link State: OPEN
Statistics:
Packets recvd: 2
Recv failures: 0
Packets xmitted: 2
Xmit failures: 0
PRI Ports being backhauled:
Slot 0, VIC 0, port 0
Configuration Auto-Download Information
=======================================
Current version-id: {894B4896-D5DC-4640-94F3-5B10212A77CB}
Last config-downloaded:00:00:00
Current state: Waiting for commands
Configuration Download statistics:
Download Attempted : 3
Download Successful : 3
Download Failed : 0
Configuration Attempted : 1
Configuration Successful : 1
Configuration Failed(Parsing): 0
Configuration Failed(config) : 0
Last config download command: New Registration
Configuration Error History:
FAX mode: disable
 
I've been having similar issues. Try restarting mgcp on the router by doing "no mgcp" and then "mgcp" in config mode. Our workaround was to add the mgcp bind commands, but you already have them.
 
Actually, I did some reading last night. I found out that one possibility is that the MGCP Endpoint wont register in CCM until the PRI Layer 1 and 2 are active.

I hadn't plugged in my pri yet as I'm not ready to cutover to my new system. I will try it out tonight to see if it works and the pri comes up ok.
 
MGCP will not register until Layer 1, 2 is up. On the controller try loopback diag- This will put a loopback on so layer will be active
 
interesting.

what's the command for that?
 
It makes the GW put the layer 1 in loop back

controller e1 x/x/x
loopback diag
 
Awesome

And in fact I tried our PRI line last night and it cutover and registered perfectly. So all is good!
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top