Search results for query: *

Set up a targ for the route and then restrict the 500 port to that route via tgar. can you give me direction on how to do this? thanks

thanks for the help so far. To answer some questions I don't have a POTS I have a ground start trunk. I have the 500 set wired to a TN not the COT. The 500 set tn will be configured with hot d to a monitoring center

I guess my question should be how do I ensure my emergency phone only uses route 9 when I pick up the phone? thanks

I probably should have mentioned its for outbound use.

I have the 500 set built but I'd like to be able to assign my office phone to the trunk to be able to test it.

I have to build an elevator emergency phone dedicated to a single line trunk. I dont know what to set at the station TN to only use this trunk. thanks in advance I have my route and trunk built as follows: TYPE TLS TKTP COT ROUT 9 TN 004 1 01 00 MBER 1 TYPE TNB TN 4 1 1 0 DATE PAGE DES...

My octel is 200. I have found my main greeting mail box and recorded a new greeting. The system is still playing the old message however. How do I get it to play the new recorded message? thanks

My company uses Octel for its auto attendant. I need to change the message. How would I know what the auto attendant mail box is? Its not identified in the listing. Is there a trace command I can use? thanks in advance

Now I'm getting different output .SSCK 0 ENBL STANDBY SYSTEM CLOCK - DTI060 PREF - 0 SREF - 25 AUTO SWREF CLK - ENBL NO ERROR .

Is this indicating clocking from loop 25 >LD 60 .SSCK 0 ENBL STANDBY SYSTEM CLOCK - TRACK ON LOOP 25 PREF - 0 SREF - 25 AUTO SWREF CLK - ENBL NO ERROR .

I'm having intermitant drop call / unable to place call issues with my Opt61c. My CSU/DSU is flashing occasional red net alarm. I have logged a call to the carrier and they are indicating no problem on their end. Where should I be looking. I reset my line counts and see SLIPR increments. I'm...

DNB 4529 which is where I want it to go to is in another PBX at another location. I tried NCFW and the call still rings to 7713. PRT TYPE ACD CUST 0 ACDN 7713 TYPE ACD CUST 0 ACDN 7713 MWC NO DSAC NO MAXP 5 SDNB NO BSCW NO ISAP NO RGAI NO...

In my 61C I have 3 cot's ATDN to 7713. which is an ACD on site. I need to change the ATDN to 4529 which is a DN at another location. I can 4 digit dial the ext 4529 from my phone and the call completes fine. The switch does not allow me to change the ATDN to a number which is not on site...

That fixed it! Thank you

I seem to have no control over any TN's in my 4 1 x x shelf, as described below. I read some other topics referencing XPEC DSBL, but am still unsure what I need to do to correct this. REQ PRT TYPE XPE XPEC S0 S1 S2 S3 LOC DIS RGTP 01 004 004 004 004 NO 08 02...

Another question, how would I UNEQ a digital trunk? I would like to UNEQ CH 5 - CH 12. DTI TRK LOOP 1 - ENBL FFMT/LCMT/YALMT: ESF/B8Z/FDL SERVICE RESTORE: YES YEL ALM PROCESS: YES ALARM STATUS : NO ALARM CH 01 - IDLE TIE CH 02 - IDLE TIE CH 03 - IDLE TIE CH 04 -...

I have a CO trunk route with 20 members. It is used for outgoing calls. SRCH is LIN. I would like to remove trunks 9-20. Do i need to do anything more than out the TN's? thanks in advance. REQ PRT TYPE RDB CUST 0 ROUT 1 TYPE RDB CUST 00 ROUT 1...

So easy thank you...

I've been tasked with consolidating / reducing the port count in my customers PBX. Also line cards must be removed from the switch since the customer pays by the port/card. It is unacceptable to them to simply out unused TN's. As I move TN's and free up cards: example I have .DISC 4 0 3...

I have 2 analog rotary bomb proof phones in my system which cannot dial. When trying to dial a 4 digit ext after the second digit it returns to dial tone. I can rec. calls on both. My first thought was COR or COS, but I can put a std touch pad phone on the frame and dial fine. Please help.