Search results for query: *

Can you run a cas t1 on a TN767E Board. or is this board only for PRI t1's Thanks

I understood that the C-lan Card could be used as a H-323 IP gateway. Is this Possible? How? thanks. If not is there an IP card that can be used as a H-323 gateway?

We currently own a couple of Definity systems. these systems had been under service contract with Avaya and we recently canceled the Service/Maintenance Contract with them. How would someone go about getting full admin rights to the systems. I would like to clear alarms and use other commands...

Hey Netcon1, Thanks for the Tip. It worked !! Just Curious though. What do the 2-5 parameters do and is there any information that I can get to explain each option Thanks again Pablo

What I would like to know is, Does it have to be Avaya or a Avaya rep to do the Upgrade or if there are some other companies that have the ability to upgrade. We have had very bad experiences with our Reps and Avaya has left a very sour taste to dealing with them. Now here is another angle. If...

Can anyone other that Avaya upgrade a Definity system. I have a G1 and would like to upgrade to a new version that will give me ISDN PRI capablities. Pablo

Hello, I am getting a busy signal when I try to call into my Definity G1 PBX through the INAD number. I have displayed the Netcon port and one of them shows busy. I cannot busy and release the ports. Can anyone tell me how to reset the port without powering down the equipment. Thanks

Problem: Connect Two PBX's. PBX A is a Definity G3. PBX B is a Definity G1. PBX A has Two T1 Pri's to PSTN and are used for all incoming and outgoing Calls. The T1 are also used to Time the Switch. PBX B is at remote location and has a point to point T1 connected to PBX A. PBX B does not have a...

I have two Definity Switches connected via two T1 tie Lines with E&M signaling. The Main Definity switch is s G3 and has two Isdn pri lines to the PSTN. The second Definity switch is a G1 and has to go through the first switch for PSTN connectivity. I need to know how if I can send the calling...

Hello 98Converter I would bet money that the problem is in the router configs. I would make sure the following commands are in the configs. call-rsvp-sync voice call send-alert voice rtp send-recv. One other thing to look at is the IOS version. Some have bugs with one way audio and such...

Hi, I don't have an answer to your question but was wondering if you can help me out. I am trying to install two PRI t1's from my CO. The T1 are DMS-250 or DMS-100 Custom. I would like to know if you can provide me with the configs for your DS1 so that I can compare them with mine. I seem to...

I believe that inorder for you to have caller ID. the T1 has to be an ISDN PRI.

Hello Everyone, I have set up a DMS-100 PRI on my Definity G3 switch. My CO says everything looks ok . they see the D-channel come up and they can pulse in 4 digit and ring an extension on my Definity. Here's the Problem, When I try to TAC into this trunk group using All I get is a busy signal...

Hello Lopez1211 Thanks for the Information. It has help out tremendously. I have another question if you don't mind. Can you give me more information on the Protocol Version. a = .... b = .... c = .... I now have a link established between the CO and the Definity but cannot TAC into the...

Hello Everyone, I need some help installing a new Board (TN 767E) I have a T1 pri from our Telco which is a DMS-100 type ISDN. I need help in setting up the DS1 board settings. The setting I have doubt in are as follow: CONNECT: (network, pbx, line-side, host) COUNTRY PROTOCOL: (1,2,3,4,...)...