Search results for query: *

So if the cfwa code is *1, the cfwd is #1 and the spre is 1, then to activate I would have to dial 1*1 and the number and to deactivate I would dial 1#1???? Or just dial *1 and number - activate, and #1 - deactivate???? Please confirm. Thanks

What is the feature code to activate and deactivate call forward to an internal extension for a 500 analog set on an Option 11? Thanks!

Does anyone know how to add off-hook station indications(BLF?)on blank keys on a 2250 console? Keys 5-19 are blank keys.

Can someone please provide detailed steps on how to setup the Opt 11C for CDR? We have OTM and would like to be able to get the CDR data through the OTM. Thanks!

We are attempting to setup OTM on an Opt 11C PBX. We have a static IP address connected to the PBX. We can ping the IP address of the PBX active ethernet link from the onsite network, connected to a Cisco switch, which is connected to our Corporate network in a different location, but we...

AT&T is the LD carrier. So, should we build a different route pattern for the ISDN calls. The existing route patterns that are for phone calls have ITC all rest.

Yes, SBC. We have other ISDN lines off of a Nortel PBX that we do not have any trouble with video conferencing out of the SBC PRI's. Does the config look correct on the BRI lines?

Someone please tell me how to program ISDN lines for h.320 video conferencing in the Avaya S8700. I programmed them as data modules with one DID number on link 1 and the 2nd DID on link 2 on each port on the T556D card. I don't see that I have 2B+D because I don't see the D channel portion for...

When programming the lines I did an add station XXXX1 and set it up as a WCBRI. I added my second station XXXX2 for the second B channel, but it would not allow me to use the same endpoint id. I used 01 for Bchannel 1 and 02 for Bchannel 2. Am I programming this correctly? What will the SPIDS...

Does anyone know how to wire and program the Avaya TN556D ISDN BRI cards for video conferencing? Our (3)existing BRI lines are off of a Nortel PBX and are 1 pair per line, 128K per line for 384K two way video conferencing. The Avaya documentation states that the BRI lines on the TN556D are 4...

Is there a way to test a 4W E&M card in the Option 11C remotely? LD 30?

jelder@reliant.com

How do I get the .kbd file?

The F6 with Procomm Plus does not do anything.

This applies to remote access, i.e., dialing in with Procomm Plus?

How do I get into the programming of the Meridian Mail system once I have typed AX after logging into the PBX and reached the Meridian Mail screen? I did a CTRL w and it took me to where I can select Console, Printer, or MMI. Where do I go from here? Thanks for any help you can provide.

Where do I send the "Success" -> End to???? I have one on my General Mailbox, one on Extension dial, one on dial by name, one on the call transfer to the operator. Do I even need the success outputs? The "ENDS" were the only things that were highlighted pink. I hid the...

Yes, I do have applicaton builder, and that is actually where I had started attempting to build the flow for the auto attendant.

Configuration > Line Data > Show Line > Line 008 > Change from Public to Pool 1, Pool 2, etc. To stop the line from ringing on the phone go to: Configuration > Line Access > Show Set ??? > Line 008 > change to unassigned and/or Configuration > Line Data > Show Line > Line 008 > change prime set...

How do you program auto attendant on a Meridian 1 Opt 11 and Call Pilot voice mail system? Thanks.