Recent content by viper222

I have an Opt 11 that is release 24. This release is EOL correct? In order to add packages, we would have to upgrade to sucession, correct? And since we still have a Meridian Mail Rls 13, that would have to be converted to a Call Pilot, correct? Finally, the Packages needed to run a PRI in...

I have a customer that has purchased BLF for their i2004 telephones, all works well, they needed them for multiple external autodails, HOWEVER, not that they programmed their autodials, it simply shows the phone number, kinda hard to tell who you want to call cause you need to remember the...

Did you ever get this resolved? If not, on a 3.5 unit I did the VNC Password reset deal, (I KNOW, not supported by Nortel, and if they ever find out they get Really Really MAD, or so I am told) but that let's you VNC into the actual unit itself. I didn't have to reset the password, so I...

We have been using the RV082 and RV042 routers from Linksys. They are not as cheap as the Netgears but they are VERY VERY stable and the RV082 supports I think 50 tunnels. Also you can set it up so the main site is a Static IP address and the other sites are Dynamic. OR you can also use a...

I second TheDirector. Stumbled upon this with another application, then tried it with the Element Manager and it worked fine. I just did the install with Compatabilty set to Windows 2000.

My Restrictions List for On Switch and Local, 1 and 2, are Restricted 0 1 2 4 5 6 7 8, and Permission 3 9. My extensions are 3xxx and then of course I figured 9 for the offsite transfer. This is the RPL found under 3)Voice Administration, 3)Restriction/Permission Lists right?

Have a customer with a MM13. Recently they lost their HD and did not have a backup. Thier vendor put in a new HD and reloaded the software from scratch, all appears to be OK, you can call in, it will answer, or if you want you can leave a message, the problem is when you try to transfer to...

OK, I have an IPKII with a PVA loaded as a Megaco 16. I have the CPU, and PVA card behind a firewall, and have programmed 10-12-01,02,and 03 with my LAN IP Address info, I have 10-12-06, the NAPT Router, check marked and 10-12-07 NAPT Router IP Address setup as my WAN IP Address. I have...

Since this has evolved to a different issue, I have reposted so here is the link, if you would like to continue helping, Thanks. http://www.tek-tips.com/viewthread.cfm?qid=1329483&page=1

OK, I started this on a different thread, but I thought I had different problem, so since it is basically a totally different issue, I am starting it here, and my old thread will point to this. I have a audiocodes gateway that is tie'ing a IVR system to my Nortel Opt 11. I have CDP setup and...

UPDATE::: Changing Gears----- After all of this, I find that it actually has nothing to do with LD versus Local at all. The Local number I was testing with was a DID for an extension in this switch. WHen I called it, the last 4 digits were 5333 so when it rang ext 5333 I thought I was calling...

Yes, acewarlock, on the distant switch they are dialing 918135551212, then adding a 9 and giving me 918135551212,(I can also see this via the DCH messages) DCH 9 UIPE_IMSG CC_SETUP_IND REF 0000001B CH 6 4 TOD 15:00:00 CK AEC44D97 CALLED #:918135551212 NUM PLAN: E164 TON: NATL CALLING...

Yes, If I turn on MSGI and MSGO in LD 96, I see 918135551212 for example, I would need to dial 918135551212 from a phone to connect to this number. If I call 98245553 I recieve on my DCH 98245553 which would need to be dialed if using a station. The 7 digit version (98245333) works and...

NCOS for a call is 3, NCOS of the 3rd pary switch is a 3 (if I knew the name, I would tell you, different vendor) I did a test and made it call an extension the I had forwarded to an LD number, it went thru I also built a ACDN and had the 3rd party call that number, it then dialed off site and...

The originating switch is the 3rd party. It sends it to the Nortel, and then the Nortel is blocking it immediantly. The nortel is taking the call from the 3rd party, then tandeming it to the PSTN BUT!!!!! from what it appears, it isn't even trying to tandem the LD calls, just the local 7 digit...