Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by timqa

  1. timqa

    NEC SV9100 IPL DSP is sporadic not working after upgrade to12.10.50

    I think I found it in the software. That is where you split up the trace into smaller segments to make it easier to search and also small enough to email correct?
  2. timqa

    NEC SV9100 IPL DSP is sporadic not working after upgrade to12.10.50

    I have a laptop set up with a port mirroring switch and running wireshark. We have pings going to show when it stops replying. Not sure what a "ring buffer" file is. Could you explain when you have time?
  3. timqa

    NEC SV9100 IPL DSP is sporadic not working after upgrade to12.10.50

    Not sure where to start to see what is not configured right? Does that look like it could be the cause of this issue?
  4. timqa

    NEC SV9100 IPL DSP is sporadic not working after upgrade to12.10.50

    I have turned off SMDR and I noticed that Automatic System Reset (90-09) was set to: Month-February Day-2 Hour-23 Not sure if this has anything to do with it but since this issue was happening every Saturday at approx. 11 PM, I did not want to chance it. We will see next weekend if it happens...
  5. timqa

    NEC SV9100 IPL DSP is sporadic not working after upgrade to12.10.50

    I agree about turning off SMDR. I don't want extra variables. I can run WireShark and it may show a constant issue but if it is one event that is causing it, it would have to be running when it happens (which is about every seven days). I reloaded the last upgrade and if it occurs again I will...
  6. timqa

    NEC SV9100 IPL DSP is sporadic not working after upgrade to12.10.50

    Some more info on this. May not be relevant but want to be thorough. This was an SV8100 that was migrated. At least a couple of years since the migration with no issues. After the upgrade to 12.10.50 from 8.00.65 approx. a week later the IP phones lose audio and no issue with digital phones (as...
  7. timqa

    NEC SV9100 IPL DSP is sporadic not working after upgrade to12.10.50

    I was thinking that this is a network issue at first but not sure now. The IP address in 84-26 does not have a physical port like the CPU (10-12). All of the digital phones stay working when this happens. They have been using the same IP address for 84-26 for many years. it was only after the...
  8. timqa

    NEC SV9100 IPL DSP is sporadic not working after upgrade to12.10.50

    After upgrade all worked but after several days, IPL DSP (84-26) is no longer ping-able and IP phones do not work. If you change the IP, everything works but stops again several days later. You can change it back to the original IP and it works again.
  9. timqa

    ATA for paging IPO V10.1

    I should have said Bogen UTI1 and I said Viking in error. I was in no way trying to down talk the Algo, I was simply saying that I don't need simultaneous paging, schedules, bells etc. They want to push a button and page. The Bogen UTI1 says it supports an analog station. I will get with them as...
  10. timqa

    ATA for paging IPO V10.1

    Thank you RocketJTech and TouchToneTommy. I forgot to include that they already have a Viking UTI-1. It is also a basic paging application and I can't see paying for the Algo over the Cisco with a $300 difference unless you know of a reason why the Cisco would not work for this?
  11. timqa

    ATA for paging IPO V10.1

    Anyone know the best ATA for paging on IPO 10.1. This is a remote site with IP phones connected to the main site. I have a Viking UTI1 on site.
  12. timqa

    WLAN 2245 password issue

    Thank you. Did not have this document. Right after my post, customer found password. I will keep document for future issues (very helpful). Thanks again for the quick response.
  13. timqa

    WLAN 2245 password issue

    WLAN 2245 password was changed by previous vendor and customer not aware of password. Is there a way to access without password? I have connected telnet over IP and serial. "Invalid password" for both connections.
  14. timqa

    Twinned call has no voice.

    Thanks amriddle01. RTP keepalives on System/Lan/Voip. No search turned up that answer but when you go to it, that is what the description states. I appreciate the help. Tim
  15. timqa

    Twinned call has no voice.

    Thank you all. It turned out to be "RTP Keepalives". All is now working. Thanks for all the responses.
See more

Part and Inventory Search

Back
Top