Recent content by pabell

Thanks ! I did put switch ID on both sides SITE A 841-863 are see to 21 SITE B 817-839 are set to 22 its the REMOTE ACCESS part I missed Thanks Pabell

FYI : side B should read POOL 890 POINT TO POINT ! Pabell

We have connected 2 magix systems using INA cards at both ends channels 1-12 DATA 13-23 Voice 24 D-channel we are doing centralized voicemail can udp calls to and from both sites but are blocked from calling through to the other side be it copper 70 or Flexpath (891) FROM SITE A ars table 2...

Phoneguy4u I'll try that but we could not even send it off a another trunk group ( in this case comes in on AT@T Megacom 800 trunk group 2 as did and we send it back out on trunk group 1 through ars routing which is a copper pots trunk group loop-start ....thanks for all the replys

It sounds like your ars table is blocking the call. With all the new prefixs for cell phones you might check the partitions and make sure the prefixs are listed. You can use "disp ars analysis partition 1 xxx" to check for your prefix...

We have a call center setup where afterhours and on weekends it calls (route to xxxx ..an x-ported extension with cover remote to offsite ...it works fine with Land lines but its BLOCKED when trying to use a cell numbers in the cover remote field ...has anyone seen something like this ????? I...

My suggestion would be to make them all wink start and have all your inbound calls be directed by DID or DNIS digits. Outbounds would be unaffected. Worst case scenario is that you have to send some calls to a calling group to ring several phones, but it seems like the way to go. if it rings...

we are installing a t1 card into a system setup as follows exsisting Setup: slot 1 slot 2 slot 3 slot 4 slot 5 308 partner 308 400 308 messaging procesor 6 port converted Setup: slot 1 slot 2 slot 3...

pbxman I was able to list bcms agent 2151 from ASA right on the server PC ....its using a ip connection to the 8300 it will pull anything list bcms agent , skill , split with no issues while in ASA. marcell55 I will try that first thing in the AM .....this is good to know as we have...

We have just upgraded our system to an S8300 rel 11 from a prologix rel 10 ....we are now using EAS with Agent Id rather then bcms login id's we can list bcms agent xxx and see the data from the switch but can not get any data from BCMS vu server if we log on as client on the desktop or right...

We are switching from a release 10 Prologix to an S8300 release 11 we had been using c-lan connection for BCMS Server and ASA from a workstation using node-names ip , ip-int ip-services ...data module (ethernet) my question is : since we do not have a c-lan or an ipsi card card in the s8300...

WE ARE HAVING AN ISSUE PUTTING A (AVAYA)LKA10 HEADSET ON A 6424D+ PHONE OFF OF IP OFFICE REL 1.3.37 ABLE TO RECEIVE CALLS ON HEADSET ....BUT NOT ABLE TO BREAK DIALTONE FROM DIALPAD ON CORDLESS HEADSET .....SO YOU CAN ANSWER CALLS BUT NOT TRANSFER THEM WE HAVE TRIED 2 DIFFERENT...

Is it possible to have an extension (voicemail) call out to more then one number ...using source number within the user as this case is its a SERVICE afterhours mailbox source number P*601 Shortcode *601 tel # 1212xxxxxx,,,,,100## (BEEPER) grp 0 feature dial works...

Logged into bash all services were up .... Tier 3 called into IP600 and put in a couple of patches 12,14,15,22 for release 10 they also did a database clean up and fix ....stop and restarted the system I had already done the stop and restart ...... I reprogrammed the ports in order for...

FYI list history shows no changes made to Hunt or members since it was setup a year ago ......I was not the one who set it up Pabell