Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: pabell
  • Order by date
  1. pabell

    Point to Point ARS magix systems

    Thanks ! I did put switch ID on both sides SITE A 841-863 are see to 21 SITE B 817-839 are set to 22 its the REMOTE ACCESS part I missed Thanks Pabell
  2. pabell

    Point to Point ARS magix systems

    FYI : side B should read POOL 890 POINT TO POINT ! Pabell
  3. pabell

    Point to Point ARS magix systems

    We have connected 2 magix systems using INA cards at both ends channels 1-12 DATA 13-23 Voice 24 D-channel we are doing centralized voicemail can udp calls to and from both sites but are blocked from calling through to the other side be it copper 70 or Flexpath (891) FROM SITE A ars table 2...
  4. pabell

    Call forwarding to cellphones from DID #

    Phoneguy4u I'll try that but we could not even send it off a another trunk group ( in this case comes in on AT@T Megacom 800 trunk group 2 as did and we send it back out on trunk group 1 through ars routing which is a copper pots trunk group loop-start ....thanks for all the replys
  5. pabell

    Call forwarding to cellphones from DID #

    It sounds like your ars table is blocking the call. With all the new prefixs for cell phones you might check the partitions and make sure the prefixs are listed. You can use "disp ars analysis partition 1 xxx" to check for your prefix...
  6. pabell

    Call forwarding to cellphones from DID #

    We have a call center setup where afterhours and on weekends it calls (route to xxxx ..an x-ported extension with cover remote to offsite ...it works fine with Land lines but its BLOCKED when trying to use a cell numbers in the cover remote field ...has anyone seen something like this ????? I...
  7. pabell

    Rel 6 w/T1 card

    My suggestion would be to make them all wink start and have all your inbound calls be directed by DID or DNIS digits. Outbounds would be unaffected. Worst case scenario is that you have to send some calls to a calling group to ring several phones, but it seems like the way to go. if it rings...
  8. pabell

    Rel 6 w/T1 card

    we are installing a t1 card into a system setup as follows exsisting Setup: slot 1 slot 2 slot 3 slot 4 slot 5 308 partner 308 400 308 messaging procesor 6 port converted Setup: slot 1 slot 2 slot 3...
  9. pabell

    BCMS Vu r2v3

    pbxman I was able to list bcms agent 2151 from ASA right on the server PC ....its using a ip connection to the 8300 it will pull anything list bcms agent , skill , split with no issues while in ASA. marcell55 I will try that first thing in the AM .....this is good to know as we have...
  10. pabell

    BCMS Vu r2v3

    We have just upgraded our system to an S8300 rel 11 from a prologix rel 10 ....we are now using EAS with Agent Id rather then bcms login id's we can list bcms agent xxx and see the data from the switch but can not get any data from BCMS vu server if we log on as client on the desktop or right...
  11. pabell

    s8300 (without C-lan)

    We are switching from a release 10 Prologix to an S8300 release 11 we had been using c-lan connection for BCMS Server and ASA from a workstation using node-names ip , ip-int ip-services ...data module (ethernet) my question is : since we do not have a c-lan or an ipsi card card in the s8300...
  12. pabell

    Cordless headsets on IP Office

    WE ARE HAVING AN ISSUE PUTTING A (AVAYA)LKA10 HEADSET ON A 6424D+ PHONE OFF OF IP OFFICE REL 1.3.37 ABLE TO RECEIVE CALLS ON HEADSET ....BUT NOT ABLE TO BREAK DIALTONE FROM DIALPAD ON CORDLESS HEADSET .....SO YOU CAN ANSWER CALLS BUT NOT TRANSFER THEM WE HAVE TRIED 2 DIFFERENT...
  13. pabell

    outcalling to more then one person

    Is it possible to have an extension (voicemail) call out to more then one number ...using source number within the user as this case is its a SERVICE afterhours mailbox source number P*601 Shortcode *601 tel # 1212xxxxxx,,,,,100## (BEEPER) grp 0 feature dial works...
  14. pabell

    IP600 with onboard Audix (Defone)

    Logged into bash all services were up .... Tier 3 called into IP600 and put in a couple of patches 12,14,15,22 for release 10 they also did a database clean up and fix ....stop and restarted the system I had already done the stop and restart ...... I reprogrammed the ports in order for...
  15. pabell

    IP600 with onboard Audix (Defone)

    FYI list history shows no changes made to Hunt or members since it was setup a year ago ......I was not the one who set it up Pabell
  16. pabell

    IP600 with onboard Audix (Defone)

    We have an issue where the Audix picks up and you hear 3 - 4 seconds of silence ....NO Alarms on Ip600 , Audix busy board a12 test board a12 (Pass) release board a12 test board a12 long clear (Pass - resolved) sa trans and did a reset system 4 Audix still picks up and silence...
  17. pabell

    NEC Electra 48 w/Elite voicemail

    I have installed a NEC Electra 48 with a voicemail Elite in slot 07 for a friend that wanted to reuse it from another site ( I mostly work on Avaya ) I worked on them awhile ago but can get around logging into x100 or x101 ...also using cosession for the voicemail *my question is this we have...
  18. pabell

    Legend V7 System Status question:

    R-Red Y-Yellow G-green
  19. pabell

    NEC Electra 48 where to start

    I have also installed a NEC Electra 48 with a voicemail Elite in slot 07 for a friend that wanted to reuse it from another site ( I mostly work on Avaya ) I worked on them awhile ago but can get around logging into x100 or x101 ...also using cosession for the voicemail *my question is this we...
  20. pabell

    IPSI TN2312AP Board

    Thanks! Able to login and set my IP Address show control interface reflects changes as well as seeing "IP" displayed on the front LCD documents say to connect "network" to the back of the IPSI board (slot #2) but I'm not able to ping .... able to ping to IPSI board...

Part and Inventory Search

Back
Top