Recent content by osurob

Good afternoon Mextera and CDRMAN, Site 1 is a 2000IPS. Site 2 is a 2000IVS. Site 3 is a 2000IVS. Site 4 is a 2000IVS2. Can I check the revision of the SC00 card through MATWorX dialed into Sites 3 & 4? Because they are 1 and 2 hours from here (Site 2).

Site 1= (Central Billing Facility) Site 2=Local Office, T1 to Site 1 Site 3=Local Office, T1 to Site 2 Site 4=Local Office, T1 to Site 2 I can see outside 10 digit calls on Sites 1 and 2 through SMDR, however, I can not see 10 digit calls being placed from Sites 3 and 4, any Ideas?

Told you it was a stupid question. Thanks Fixin for that answer! Rob

Dumb question from a relative newbie: Does CMD08>141> “Recording Station to Station calls automatically” mean Station to Station calls on the same switch will be sent to SMDR? Or by “Recording” do they mean something other than SMDR? Thanks Guys

Good Morning, What commands on a 2000IVS2 Local Office would cause our Central Office (AIMWorX) to only see 4 digit office to office calls from that site and not outside 10 digit calls? FYI: This site connects to another of our 2000IVS2 sites through a T1 and CCIS first. Thank You

On one site that’s T1'd to another site, then T1'd to our ADMIN (Central, main)site, I can only see direct 4 digit dialing to our other sites, how do I make it so that I can see external calls i.e. (800)555-1234 placed from that site? Thanks

Good Morning, We have five 2000IVS (Local Office), two 2000IVS2 Local Office), and one 2000IPS (Central Office, Admin switch). SETUP OF OFFICES -Admin’s 2000IPS has four T1’s connected to Local offices. -One of those four Offices is connected to another Office through a second T1...

Now they tell me *1 works but, they used to use the (Pick) softkey and it did the same thing as (*1). With the IPS upgrade however, they must press (Pick) then dial the ringing extension... darn lazy employees! hehe Gary is there any way to edit the (Pick) softkey to make it act similar to...

Thanks Greg, they had Busy and No Answer both programed for their virtual number. I changed the no answer on the prime line to Voicemail and it works perfect! Thanks again Greg

Good Morning Gary, Thanks Gary, I checked and everything is correct in CMD160. I think it's the (*1) code that's lost. Before they could pickup their phone and just press (*1) and they'd get the ringing line. Now they have to press soft key (Pick) then dial the ringing extension. Does this...

Good Morning, We currently upgraded our 2000IVS processor to IPS. NEC tech converted the programming and installed the upgrade. Before the upgrade we had a call pickup group setup for 5 phones, all they had to do was pick up one of those phones and press (*1) to grab the ringing phone, now...

Good Morning, I have a 2000IVS and only on one phone does it seem to ring too many times before going to Voicemail. If we had this problem on all phones I'd at least know where to begin looking. Any Ideas? Thanks Rob

Good Morning All, Does anyone have a SMDR cheat sheet for the NEAX 2000IVS/IPS series systems. Thank You in advance! Rob

Two of our 2000IVS’s run CCIS through split (Data/Voice) T1’s that are attached to a local 2000IVS. Because of the cost per distance we had to split these T1’s and are using only the first 8 channels of the T1 for voice. NECBNS set these two sites up a couple years ago and now I’m trying to...

I checked CMD001>82>,102,122,142 to make sure the format was set to 2400 (i.e. #3) in all relevant channels, which they were already correctly set. I really think the key is that instead of one line of data (i.e. from Ext. to Ext./Phone #) I'm getting two lines which look like the first line is...