Recent content by nscripta

Checked the SERV parameter, all outgoing routes have D10 in SERV as 1 which according to ALEX is 'number conversion shall be made' ROUTE CATEGORY DATA ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP 1 0120000000000010 5 2110030001 0 30 128 00010111...

I need to modify a couple of analogue extensions on a MX-One Telephony Server to send a different number as their CLI to the terminating exchange. At present the DDI number is sent as the CLI. I have tried to add this facility using the number_conversion_initiate command with various parameters...

RDR printout from LD 21: REQ: prt TYPE: rdr TYPE RDR_DATA CUST 0 TYPE RDR_DATA CUST 00 OPT CFO CFRA DSTD PVCA CWRD FNAD FDN FNAT FDN FNAL FDN CFTA NO CCFWDN CFN0 6 CFN1 6 CFN2 8 DFN0 6 DFN1 6 DFN2 8 DNDH NO MDID NO NDID NO MWFB NO TRCL 0 DFNR 0 CRT0 00 00 00 00 CRT1 00 00 00 00...

Copy of one of the phones: DES MAIN1 TN 002 0 00 00 TYPE 2616 CDEN 8D CUST 0 AOM 2 FDN 301 TGAR 0 LDN NO NCOS 5 SGRP 0 RNPG 0 SSU 0010 XLST SCPW 301 CLS TLD FBD WTD LPR MTD FNA HTA ADD HFA MWA LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1 POD DSX VMD CMSD CCSD SWD LND CNDA...

Three digital phone which accept incoming calls on a ddi route are diverting after 6 rings to one of the 3 prime numbers, display on diverted call phone states incoming number label and "CFNA". All three phone have all their forwarding functions (EHT,FDN etc) set to the their own prime number...

PC-Regen for the md110 exchanges generates an exchange rebuild file by requesting multiple print commands, analysing the information and then creating the command list necessary to duplicate the configuration. Is there an equivelant application for the meridian? I am looking to test some...

The switch is unlikely to be upgraded, it is used in a bespoke configuration with the current version the only approved one. A web search identified my issues as a common problem when creating digital sets with many hot lines. The error code refers to ADL/CFW exceeds the maximum length of the...

Changes carried out to an option 11c to add both way hotlines to existing digital sets caused multiple 5222 errors to be displayed. A search on tek-tips forum indicated that it can be associated with the template and users have reported success if a new DN is created and then add the hotlines...

Thanks firebirdscrambler, Exactly the info I needed! :) Have you checked out my generic exchange app, for serial input you may find it useful. http://tek-tips.com/viewthread.cfm?qid=1709910 nscripta

Incoming calls presented on our DDI -trunks do not always display a name, however always show the trunk label and digits received. The name display is directly associated with the number received. Is the name display dependent on what is being sent from the public network? (DAS) Or can The name...

For some strange reason I was thinking the terminating dn on a two way hotline couldn't be an external number!! [ponder] I actually came up with a workaround that solved the issue using a phantom dn in the both way hotline configuration. The phantom dn was call forwarded to the external number...

Trying to get the equivelant of both way hotline working involving an external number. Would a permanent call forward to an external number which is programmed as the remote destination in a HOT D key configuration allow both way hotline to be achieved? The external number already dials a...

Maybe I haven't explained correctly, I need the equivelant of: HOT D nn 'External number' 'Internal number' The configuration will be hard coded, the method of operation as follows: Incoming call - external party goes off hook, causing it to dial a pre programming ddi number, the button on...

Looking for a solution to get both way hotline working on keys on a digital phone. At present the keys are programmed as an SCR, the incoming calls are presented by BT over an ISDN30 link effectively as DDI routing, with the last 3 digits sent to match with the key presentation. Is there a way I...

Any time I need to access a Meridian I can't remember the command sequences so I have now developed my Exchange Comms Application. The app provides a means of creating sequences for dynamic buttons which are loaded from their respective files on startup.(buttons directory) The app can be...