Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by NARBE

  1. NARBE

    SNMPv3 Issues, can anyone help?

    Hello, To start using snmpv3 I let you some command lines that will help you. conf t snmp-server view writetest +1.3 ! thats create a view snmp-server user RW read-view writetest write-view writetest sha <authentication-password> aes <privacy-password> ! thats create a user and associate to a...
  2. NARBE

    ERS8600 with version 5.0.0.1 and HA-CPU problem

    We have disabled HA mode and it looks ok now. Thank you
  3. NARBE

    ospf over static route preference

    You need to change the preference (Nortel ERS) Default preferences for an ERS: ---------------------------------------------------------- local 0 0 static 5 5 ospfIntra 20 20 ospfInter 25 25 ebgp 45 45 rip 100 100 ospfExternal1 120 120 ospfExternal2 125 125 ibgp 175 175 staticv6 5 5 ospfv3Intra...
  4. NARBE

    ERS8600 with version 5.0.0.1 and HA-CPU problem

    Hello, Someone has already tested the version 5.0.0.1 on ERS8610 with HA-CPU. I have upgraded 5 ERS to this version and I have starnge log error messages: ------------------------------------------------------------ CPU5 [11/03/08 07:33:35] SNMP INFO Communication established with backup CPU...
  5. NARBE

    Nortel 8300 switching function

    Hi, Did you have the version 4.0.0.0. If yes upgrade to the 4.0.2.0. Can you show a sniff sample?
  6. NARBE

    Nortel 8300 switching function

    Hi, Witch version? The ISA servers are used with teaming or nlb? Could you show a trace sample?
  7. NARBE

    IPO 500 - ip phone 5600 randm reboot

    We found a workaround: downgrade the ip-phones firmware to version:2.3. It looks fine now, no more random reboots
  8. NARBE

    IPO 500 - ip phone 5600 randm reboot

    I first use a 4510 (Cisco) and I check that I have enough power (My phones were well know as Class2 by the Cisco). As I explain I have also tested with a mispan (power injector) and an Enterasys switch (no poe) and I get the same issue. We're upgrading the IPO to 4.1.15 I let you know.
  9. NARBE

    IPO 500 - ip phone 5600 randm reboot

    Hello, We have an IPO 500 version 4.1.12(01) and ip phones version 2.8.3. All works fine but the phones ramdonly reboot (we ha'nt any message on the ip phone like "discovering" or "no ethernet") We have tested with poe-switch and with midspan, same issue. Thank you for your help.
  10. NARBE

    Port mirror on a 4548GT-PWR

    Hi, Sorry I don't read well the doc from Nortel but now you can use port-mirroring with the following capabilities: • Monitor all traffic received by port X. • Monitor all traffic transmitted by port X. • Monitor all traffic received and transmitted by port X. • Monitor all traffic received by...
  11. NARBE

    Port mirror on a 4548GT-PWR

    Hi, I never use but with the filter you can use an "interface action extension" You can create L2 filter and use this "action extension" to egress all the matching traffic to an interface. Let me know
  12. NARBE

    Help for a newbie. Vlans across switches

    Hello, You must use too: enable ipforwarding vlan <vlan-name> for each vlan do a sho ipconfig (or show vlan) to see the ipstatus on your vlans Regards
  13. NARBE

    Cannot ping across vlans

    Did you enable ipforwarding on the vlans (just type enable ipforwarding vlan xxx)
  14. NARBE

    Help with ACL (x450)

    Hi, I never try on extreme but I think i'll work. First rule add a permit from 0.0.0.0 to DHCPServer@IP udp source 67 udp destination 68 2nd rule block udp traffic port source 67 to port destination 68 from 0.0.0.0 to 0.0.0.0. Or you can just use the 2nd rule applied to all ports except the...
  15. NARBE

    Business Policy Switch 2000 lost password

    Hello, Popwer down the switch, plug a console, press 'Crtl c' when rebooting, a new menu appears and press 'i' (if I remember good!) Your switch will be reset to the Factory Default config ( be careful all the config is reset!) Have you tried password : user or secure? Greetings Narbe

Part and Inventory Search

Back
Top