Recent content by Midnite1971

OK....thanks for all the advice guys!! Anyone maybe have an idea of how this happened or what may have caused it? I currently have the maint. vendor on their way out.

OK.....can I split them while it says syncing? What would be the process besides the command SPLIT and SHDW?

OK....it's been like that for almost an hour....should I start worrying? A sync only takes about 30 to 45 minutes correct?

It sure does.....but now when I just went in it shows them as syncing even though I never did anything...weird. cp 1 16 PASS -- ENBL SYNCING DISK STATE = REDUNDANT HEALTH = 24 VERSION = Jul 28 2005, 04:14:02 Side = 1, DRAM SIZE = 512 MBytes cp 0 16 PASS -- STDBY SYNCING DISK STATE =...

Cables have been swapped out for new and the links are active...any other ideas?

Hey People.... CS 1000, 4.5 Normally I switch cores every once in a while just as a precaution but now I'm getting a failure...any ideas? CCED000 .scpu OK . SRPT048 DR: Master asked to stop updates and flush file system. CCED763 LCS: Graceful Switchover. Call Processing Stopped at 07:22:36...

CS1000 4.5 Could someone please explain exactly what happened through these logs? I know that the link to CCM went down...but why? Thanks TIM461 13:36 29/10/2008 CPU 1 % % AUD021 073520B2 00001002 00000003 00001908 00000000 00000000 00000013 00001908 % % AUD028 073520B2 00001002 00000003...

Thanks for your help!!!

Is there a way to print all phones that have a specific RCO? Thanks Tim

Thanks so much for your help.....it's appreciated. I have turned on dch messaging in and out for both of those PRIs....and we're an Outbound Call Center. Will so many messages being spit out affect the PBX in any way? Thanks

5ESS....set at NI2...here's the Dch programming. On one of the PRIs they had it setup with RCAP- COLP and NDS, I removed NDS and at least the fast busies went away. ADAN DCH 1 CTYP MSDL DNUM 14 PORT 3 DES PAETEC USR PRI DCHL 25 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK...

OK....here's one with hex. Thanks!! DCH 1 UIPE_IMSG CC_SETUP_IND REF 00007F83 CH 25 7 TOD 10:45:23 CK DB249E77 PRIM HDR: 2F 00 03 00 5C 00 MSG HDR: 08 02 03 FF 2E 00 BCAP: 01 07 13 00 85 90 00 00 A2 CHID: 09 09 0D 00 A9 00 83 00 01 0CAD#: 03 0A 03 00 80 00 04 00 07 06 07 08 GFFAC: 37 1A 19...

It does except for those several setup messages...and they happen on every call out of that PRI. DCH 1 UIPE_IMSG CC_FAC_IND REF 00003C03 CH 25 4 TOD 9:39:31 CK DAAC01D1 DCH 1 UIPE_IMSG CC_FAC_IND REF 00003C83 CH 25 5 TOD 9:39:35 CK DAAC2934

I've turned on d-channel messaging and one of our PRIs keeps having an incoming CC_FAC_IND message. What does this mean? I understand the alert messages but not the facility messages and our other PRI does not do this. CS1000 4.5 Thanks DCH 1 UIPE_IMSG CC_SETUP_IND REF 00003C03 CH 25 4 TOD...

OK....I have one...what is a Cause: #31 DCH 5 UIPE_OMSG CC_SETUP_REQ REF 00005394 CH 13 17 TOD 14:28:32 CK 56D6F19D PROGRESS: ORIGINATING END IS NOT ISDN CALLING #:18884958645 NUM PLAN: E164 TON: NATL CALLED #:12124873702 NUM PLAN: E164 TON: NATL DCH 5 UIPE_IMSG CC_PROCEED_IND REF...