Recent content by electrobank

OK... So from what i have no ACD is programmed on the lines... and the Fiber needs to be pulled with the switch off... i can do that late nigth... I hope i'm no naggin' with my questions but... i'll shut down... remove the fiber connected betwee 1 and 3 and turn on the switch... nothing more...

What is this ACD? here's a print out of my extension... and about the last cabinet... just pull the plug and disconnect the Fiber that goes from the main cabinet to the empty cabinet is OK???? i just want to double and triple check before i start this process... DES PRUEBA TN 005 0 00 00...

Guys... I was about to do the card move and i realized the followng... > how do i disable the empty cabinet? i just need 2 and the 3 will be removed and stored. > the cards can be moved while the PABX is on? or i need to do the ld 25 and then shut down and move? i'll run new jumpers because...

and what about the empty cabinet? just power off?

ok. just to clarify. ld 25 then mov... and my questions >the system ask me wich card and where to? >this move includes all the TN information associated with the move? > finally: after moving the 2 cards, can i just shut down that cabinet or i need to do something else?

Hi there people... new question... here's what i have; Meridian 1 version 2111 release 22 issue 46+ that has 3 cabinets installled. cabinet 1 have DTI Cards, meridian mail, and some line and trunk cards, cabinet 2 has line card and cabinet 3 only have 2 line cards (both analog) the cabinets...

THNX FOR THE HELP!

HEY I MANAGED TO FIGURE OUT HOW TO CHANGE THE CODE USED FOR THE FEATURE. I JUST NEED TO KNOW WHAT SHOULD I DIAL NOW TO GET IT TO WORK.

Here what i got from ld 21 ffc printout >LD 21 PT1000 REQ: PRT TYPE: FFC TYPE FFC_DATA CUST 0 TYPE FFC_DATA CUST 00 CCRS SRE SCPL 4 SBUP YES FFCS NO STRL 0 STRG ADLD 0 AND HERE WHAT I HAVE ON LD 57 REQ PRT TYPE FFC CUST 0 CODE CFWA CUST 00 FFCT YES CFWA #1 CODE CFWD CUST 00 FFCT YES...

I managed to get on each of the digital TNs and do a manual Forward. as for the Analogs, i don't know what key sequence to dial from the phone to have the CFW active and i can't manage to get it working from the CLI. if anyone know how to print os see what is the sequence (i.e. to lock a pone i...

I guess I used the wrong term. By console I meant the programming console (were i enter the commands) and not the 2250. and about the software and stuff, this is wat I have: VERSION 1411 RELEASE 21 ISSUE 23 FW09 +

hi there, i have a meridian 1 and i'm trying to figure out how can i do a call forward from the console. we're remodeling and all the customers were moved to shared spaces so i have to forward on a 4:1 ratio (4 users/phones to 1 "receiving" phone), this is a temporary move and i want to know...

OK... so i need this 2 cards... now i have more questions: 1. the SILC Card will receive the data from the E1? 2. the MISP Card is the one were i actually connect the conferencing system?

Anyone knows wich cards do i need to have video conference enabled on a Meridian 1 option 11c? i know that the call will run trough a ISDN card but i don't know wich type do i need (ISDN/Bri or PRI)

i did what you said... but nothing changed... what about that test command? also, is there a way to run a diagnostic or something to test the 2250? some software or LD... finally... if the 2250 is damaged we won't replace it with a new 2250 but a 2616 with keypad add on, what should i do to get...