Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by bizsoftware1

  1. bizsoftware1

    callers required to enter pin

    Thank you both for the two scenarios, very much appreciated :-))
  2. bizsoftware1

    callers required to enter pin

    Hi, I wonder if someone could point me in the right direction, I have been tasked with providing a way for an ipo voicemail pro to provide callers with an option to contact a representitive on call, however they must validate that they are allowed to do this by entering a pin. ie. caller is...
  3. bizsoftware1

    Draytel Sip Trunks

    Not on mine, i have snmp and T1 either side of system tab, im using version 4.1(15)
  4. bizsoftware1

    Draytel Sip Trunks

    lol no, im strugling to find the settings in monitor, im using version 4.1(15) I have turned on development logging, and then selected all items under H323. I appreciate some direction!
  5. bizsoftware1

    Draytel Sip Trunks

    ********** Warning: Logging to Screen Started ********** 282416mS CMCallPkt: v=0 CMSetup (Secondary) Line: type=AnalogueExtn 2 Call: lid=0 id=2 in=0 Called SubAddress[d] Calling[] Type=Unknown (0) Calling SubAddress[?²H] Pres=Allowed (0) Keypad[‘|N ‘|ìáC]...
  6. bizsoftware1

    Draytel Sip Trunks

    theproviderpatched - how can i email you the config??
  7. bizsoftware1

    Draytel Sip Trunks

    39079mS CMTARGET: 0.1015.0 3 MasterBedroom.0: TimerExpired cause=CMTCDelayedProcessing 39081mS CMTARGET: 0.1015.0 3 MasterBedroom.0: LOOKUP CALL ROUTE: type=100 called_party=7 sub= calling=202 in=0 complete=0 ses=0 39081mS CMTARGET: OUTGOING CALL ROUTE 39082mS CMTARGET: 0.1015.0 3...
  8. bizsoftware1

    Draytel Sip Trunks

    akb1111 i have analogue extentions only on this unit, so no info........ im guessing its waiting for line as nothing happens!
  9. bizsoftware1

    Draytel Sip Trunks

    i do not see any filter settings for sip, can you enlighten me please?
  10. bizsoftware1

    Draytel Sip Trunks

    hi, i still cannot overcome this problem and am finding it difficuilt to find the time to invetigate further, does anybody know a good engineer near to milton keynes, uk i could contact??
  11. bizsoftware1

    Draytel Sip Trunks

    Just out of curiosity i have my laptop patched in to lan 1, and i can ping my sip provider no problem, however my ip address is comming from my router, not ipo. When i try to ping my sip provider from the status application it fails on all three packets and shows the source as lan1 ip address...
  12. bizsoftware1

    Draytel Sip Trunks

    Can someone confirm my network settings, i am still having issues! I have lan2 as follows; Stun server 69.90.168.13 (default) firewall port restricted nat binding refresh 20 public ip is my public ip public port 37892 (default) stun port 3478 I get the warning; Communication is not possible...
  13. bizsoftware1

    Draytel Sip Trunks

    Thank you peter, I will try your suggestions, my provider does not support stun, but leaving the avaya defaults it sets up as Full Cone NAT. My short code is as follows; Code: *9* Feature: Dial Tel Number: "9123@draytel.org" Line Group id: 5 Locale: uk 9123 is the talking clock at my sip...
  14. bizsoftware1

    Draytel Sip Trunks

    I have a little more, i have setup a short code to draytels talking clock and then dialled it, this is the log 33072mS CMTARGET: 0.1004.0 1 MasterBedroom.0: LOOKUP CALL ROUTE: type=100 called_party=*9* sub= calling=202 in=0 complete=0 ses=0 33073mS CMTARGET: OUTGOING CALL ROUTE 33074mS...
  15. bizsoftware1

    Draytel Sip Trunks

    Bas That was from sysmonitor tool, but i cannot find a setting to enable sip in the filters?? I am using version 4.1 (15) Any ideas??
See more

Part and Inventory Search

Back
Top