Recent content by aghamir

is there a command to issue to disconnect the remore client modem when the his/her session is done? thanks

Please any help on this issue. It's very important thanks

I have an E1 connected to an AS5300. The problem is when I do show controller e1 0 timeslots 1-31, all the lines are idle. Then after that they start to display "connected" until all of them are used and clients start complaining about a busy line. I have to manually go into the RAS and issue a...

Hi Guys, I have a 3640.It was working fine and today when I tried started it after reboot, it didn't finish all the steps and stopped with "failed to initialize" no prompt. I've tried going into ROM mode and when I typed rommon2>reset it took me back to the old screen. Could that be a corrupted...

jimmyzz, I did exactly what outlined in eurobadger's post. 9- Type enable at the Router> prompt. You'll be in enable mode and see the Router# prompt. 10- Important: Type configure memory or copy startup-config running-config to copy the nonvolatile RAM (NVRAM) into memory. Do not type...

I did exactly what outlined in eurobadger's post. 9- Type enable at the Router> prompt. You'll be in enable mode and see the Router# prompt. 10- Important: Type configure memory or copy startup-config running-config to copy the nonvolatile RAM (NVRAM) into memory. Do not type configure...

Yes routerman. I was able to confreg the 0x2142 register, reset the router, go into enable mode, run configure memory and that's it. No more commands all Iget after that is: Greenwich_3640# 00:03:10: %AAAA-3-INVSTATE: AUTHOR/CMD: Internal state is invalid: astruct 0x61 71FC48 ustruct 0x0...

thanks jimmyzz, I followed all the instructions for the password recovery but the problem as I outlined in my previous post is that when I do enable and get router_name# prompt, the ourter is not letting me execute any commands (none) and gives me the following error message: Greenwich_3640#...

Guys, Please help, I need to resolve this issue ASAP. Is there a way to clear all the settings and hard reset the router. I really don't care about the config file since I'm frustrated with this router. I always tought that Cisco was the best but never tought that it's so hard to reset a cisco...

fmonteiro, Actually I bought it from ebay and now I'm stuck with it. How can I change the config to bypass authentication or better wipe out the whole config thing and go back to default settings. It must be a way to overcome this problem right? thanks,

But how can I bypass tha "AAA/TACACS/Radius" part of the config file and wipe out everything. Please help thanks

I need to reset a 3640 router but all I'm getting is this error message: Greenwich_3640# 00:03:10: %AAAA-3-INVSTATE: AUTHOR/CMD: Internal state is invalid: astruct 0x61 71FC48 ustruct 0x0 -Traceback= 601BE240 601BE120 601F1438 601F1EB8 601FCAAC 6023BF64 6023BF50 what does it mean and how to...

I get this error message: Greenwich_3640# 00:03:10: %AAAA-3-INVSTATE: AUTHOR/CMD: Internal state is invalid: astruct 0x61 71FC48 ustruct 0x0 -Traceback= 601BE240 601BE120 601F1438 601F1EB8 601FCAAC 6023BF64 6023BF50 what does it mean and how to fix it? many thanks,

fmonteiro, That's weird but when I get to the prompt <router_name># and type &quot;write erase&quot; or enable secret <apssword> this is what I get: &quot;Command authorization failed&quot; why? thanks

tschouten, thanks for the quick response. Can you please give in detail the steps required to wipe out the configuration and reboot the system from scratch? thanks a lot