×
INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Students Click Here

Lots of questions....

Lots of questions....

Lots of questions....

(OP)
I own a MICS 4.1 using 6 fibre combo port and looking to get my 4.1 XC so I can add another 6 fibre combo ports.  I have a T1 card in but no DID service yet.  

I'm looking to get DIDs soon and just want to make sure that DID can be carry over T1 ?  

I also have more than 48 users so using the 4port star flash won't work.  I'm assuming I need to go NAM ?  how hard is it to hook up a NAM voice mail ?

Is it hard to do any of these ?  I'm not a super phone guy but I learn the system and looking for advice..

In CT area..

RE: Lots of questions....

YES, you can run DID's over a T1. The NAM will is not that hard to setup. It has a fiber feed just like the other modules. A installation guide will be sent out with the product. Make sure the versions are correct for the MICS and NAM.

“Reserve your right to think, for even to think wrongly is better than not to think at all”

Fisher CCNA,(CCNP-Routing)
UOP Student BSIT

RE: Lots of questions....

How to Install a T1:

You must have either a Services Cartridge (slot 1) or a 6-port Combo card (slot 2) in order to provide clocking for the T-1. Only one of these is needed, even if you have two DTI cards.
The DTI card should go into Slot 4 first. If you have a second card it would go into Slot 3.
You must disable the card first, program the card for T1, then re-enable the card.

To Disable / Enable Card
From Terminals & Sets – Next until you get to Maintenance – Show
Next until get to Module Status – Show
Show module – Next
KSU (1):        Next or State if using (2) cards
KSU (2):        State
( ) Ports Busy – Press Disable or Enable
Disable at Once? – Yes

Protocols & Signaling
Hardware – Show
Show Module – Next
Cards on KSU – Show
Cd1 – KSU:        Change to T-1 – Show
Card Type T-1 – Next
Lines: 001-024 – Next
Protocol: SL1 – Next (check with your Telco Carrier for setting)
Type Slave – Next
Bchanseq: Ascend or Descend – Next (check with your Telco Carrier for setting)
CO Fail: TIA–547A – Next
IF Levels: ISDN – Next
Framing: ESF – Next (usually ESF, check with your Carrier
Internal CSU: ON – Next
{need to have either an external CSU or turn the internal one on. If customer needs to use some channels for data then they’ll need a CSU/DSU to split off channels before the 0X32. OR to split off data channels after 0X32 they’ll need a Nortel Data Interface (NDI) plus bandwidth allocation key codes}
DSX1 Bld: 000-100
Line Coding: B8ZS (usually B8ZS, check with the Carrier)
ClockSrc: Primary (second card would be secondary)

Re-enable the card in Maintenance now.

Channel Set Up
From Lines: - Show
Line001:Line001 – Show (you’re entering your channel numbers here. If you’re using                     straight DID cards, then you’ll begin with ‘line’ 049)
Trunk/Line data – Show
TrunkType: E&M – Next
Line type: Pool A - Next
Dial Mode: Tone – Next
PrimeSet: 221 – Next
Auto privacy: Y – Next
Ans Mode: Auto – Next
Ans with DISA: N – Next
Aux. Ringer: N – Next
Signal: WinkStart – Next
ANI number: N – Next
End of List

Target Lines Programming:
From Lines – Show
Show LN: 145 – Show (target line range from 145-275 non-XC SW, 145-336 XC SW)
Target LN – Next
Private to: (extension number) – Next
Rec’d #: (enter digits Telco is sending) – Next
If Busy: to prime – Next
PrimeSet: 221 change to the extension # - Next
CLID Set: None – Next
Aux. Ringer: N – Next
End of list

MRoberts

RE: Lots of questions....

(OP)
Actually the T1 card is already installed, we had T1 service before but not DID, out going DOD.  Thanks for the info, I actually have 2 6port combo card, in 1 & 2 I think.  I'll have to check

RE: Lots of questions....

If they are two way DIDs as in the users can get DID calls and make calls out over the T-1 then that's where you would set up the Channels as E&M. That way you can get traffic both ways over the T

MRoberts

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members! Already a Member? Login

Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close