×
INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!
  • Students Click Here

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Students Click Here

MICS DR 3.0 E & M snd TARGET Line Configuration

MICS DR 3.0 E & M snd TARGET Line Configuration

MICS DR 3.0 E & M snd TARGET Line Configuration

(OP)
I have 12 e+m lines (lines 013-024) from a T1 on a corporate lan. all lines in poolB. Sprint strips out all but the last 3 digits upon handoff the switch. I have dialtone and can place calls on any of the 12 lines.   Incoming lan calls need to ring at the appropriate sets. 3 digit DN's. I expect I need to somehow map the target lines to the sets. Any help will be greatly appreciated.
Thanks

RE: MICS DR 3.0 E & M snd TARGET Line Configuration

Given the E&M's are sending digits than yes target lines can be setup. Start at target line 145 (I believe) try one and then prgram the rest.

“Reserve your right to think, for even to think wrongly is better than not to think at all”

Fisher CCNA,(CCNP-Routing)
UOP Student BSIT

RE: MICS DR 3.0 E & M snd TARGET Line Configuration

Target Lines Programming:
From Lines – Show
Show LN: 145 – Show (target line range from 145-275 non-XC SW, 145-336 XC SW)
Target LN – Next
Private to: (extension number) – Next
Rec’d #: (enter digits Telco is sending) – Next
If Busy: to prime – Next
PrimeSet: 221 change to the extension # - Next
CLID Set: None – Next
Aux. Ringer: N – Next
End of list

Then just assing the Target line to the phone. If it is E&M then in order for one side to dial the other side, each extention will need a target line set up for the extension. IE., Target line 145.... received digits 221.... assigned to appear and ring at extension 221. When the other side picks up, accesses the E&M trunks, dials the desired extension 221 the target line 145 will pick up on the digits 221 and ring the extension.



MRoberts

RE: MICS DR 3.0 E & M snd TARGET Line Configuration

Target Lines Programming:
From Lines – Show
Show LN: 145 – Show (target line range from 145-275 non-XC SW, 145-336 XC SW)
Target LN – Next
Private to: (extension number) – Next
Rec’d #: (enter digits Telco is sending) – Next
If Busy: to prime – Next
PrimeSet: 221 change to the extension # - Next
CLID Set: None – Next
Aux. Ringer: N – Next
End of list

Then just assign the Target line to the phone. If it is E&M then in order for one side to dial the other side, each extention will need a target line set up for the extension. IE., Target line 145.... received digits 221.... assigned to appear and ring at extension 221. When the other side picks up, accesses the E&M trunks, dials the desired extension 221 the target line 145 will pick up on the digits 221 and ring the extension.



MRoberts

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members! Already a Member? Login

Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close