×
INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Contact US

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Students Click Here

EX Controller MiVB - A few questions

EX Controller MiVB - A few questions

EX Controller MiVB - A few questions

(OP)
Hi,

Just connected an Euro-ISDN to an EX Controller and it does not work. questions:

-How do I limit the E1 to only the first 10 channels? In the 3300 I simply only added a trunk number to the first 10 ports, how do I do this with the EX?

-How do I check the status of the channles? I used to do ST and the PLID

-How do I do the equivalent to CCS Trace on the E1 port?

Regards,

daniel

www.hatkanatelecom.com

RE: EX Controller MiVB - A few questions

there is a kms article for trace


Title
EX how to capture the equivalent of EDT trace for Mivb
Objective
Use the following steps to capture what the Pri link is seeing on the Mediatrix side of the solution.
How to capture the equivalent of L2L3 trace on the EX controller
The EX does not support the edt trace tsp L2L3 like the MXE3 and CX(i)2’s do as there are no physical plids or trunk numbers.

We need to capture the trace on the Mediatrix side to see what is coming in on the Framer/T1 Module with regard to ANI and DNIS
Environment
EX controller
Mivoice Business
ISDN
Pri
Procedure
1-Login to the EX (Mediatrix) side
2-Under System/Event log
3-The Remote Host will be the IP address of the Laptop or PC which will be running Wireshark
4-For Diagnostic Traces, select Enable
5-For Filter, click on Edit
6-A new box opens, and you will select what it is you want to trace
7-Since we are tracing only ISDN, leave that as the only Module you wish to capture.
NOTE: the next phase of the call routing is SIP so there may be a requirement to enable SIP as well to validate that the DNIS of the Pri is the same as what the invite toward the Mivb contains.
8-Click on apply
9-Click on apply again when you revert back to the previous page.
10-With Wireshark running, make your test call.
Once you have your capture, you need to find the IsdnStackL3Msg for the following categories:
IE Display, IE Calling Party Number, IE Called Party Number
IE Display will show you the NAME
IE Calling Party Number will show the ANI
IE Calling Party Number will show the DNIS




One completed, best practice is to disable the Diagnostic Traces.

If I never did anything I'd never done before , I'd never do anything.....

RE: EX Controller MiVB - A few questions


-How do I limit the E1 to only the first 10 channels? In the 3300 I simply only added a trunk number to the first 10 ports, how do I do this with the EX?
-How do I check the status of the channles?

Login to the EX (Mediatrix) side

ISDN -> Primary Rate Interface -> select your Slot number ( for example 1 if you have only one E1T1 card ) --> Channel rage : i you want 10 then : 1-10

to monitor :

ISDN -> Status


Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members! Already a Member? Login

Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close