iPECS 100 - Want additional extension to ring when call internally
iPECS 100 - Want additional extension to ring when call internally
(OP)
Hi all,
We have a iPECS 100 running F1Dh software
We have lots of remote sites connected to our head office phone system, all works very well with SIP and ISDN30 for inbound lines
What we would like is if we call one of the internal extension numbers, say 246, which is a 8012E phone, we would also like extension 240 to ring at the same time
Basically, extension 240 is a bell in the workshop, so when we call the handset in the office, the bell also rings, so they know to come and answer the phone
Most sites will have 3-4 extensions, so we would like extension 240 to ring for them all
I have looked through all the station attributes, and can't see a way of doing this,
This is only for internal calls, external is fine, as the bell is in the ringing group,
Any help, greatly apricaited,
Paul
We have a iPECS 100 running F1Dh software
We have lots of remote sites connected to our head office phone system, all works very well with SIP and ISDN30 for inbound lines
What we would like is if we call one of the internal extension numbers, say 246, which is a 8012E phone, we would also like extension 240 to ring at the same time
Basically, extension 240 is a bell in the workshop, so when we call the handset in the office, the bell also rings, so they know to come and answer the phone
Most sites will have 3-4 extensions, so we would like extension 240 to ring for them all
I have looked through all the station attributes, and can't see a way of doing this,
This is only for internal calls, external is fine, as the bell is in the ringing group,
Any help, greatly apricaited,
Paul
Talk To Other Members
RE: iPECS 100 - Want additional extension to ring when call internally
RE: iPECS 100 - Want additional extension to ring when call internally
Have looked in there before, unless I am doing something wrong, it doesn't appears to save it
Do I have to fill in the MAC address, IP and Router address for each ? what about station type, is that IPKTI ?
Do I just put the bell extension number in the slave STA number on the right ?
Do ARP, register and codec matter ?
Thanks again,
Paul
RE: iPECS 100 - Want additional extension to ring when call internally
RE: iPECS 100 - Want additional extension to ring when call internally
I set the 'Master Station' to be ext 244 - the bell
In the Group Members I added ext 241 + 242 + 243
Saved, then when I tried to dial 241 from my own office phone, it just comes up invalid
Tried all the options in 261 (Personal Group Attribute) and made no difference
Seems we are so close, yet so far
Thanks everyone
Paul
RE: iPECS 100 - Want additional extension to ring when call internally
Create a group for each extension you want the bell to ring with.
RE: iPECS 100 - Want additional extension to ring when call internally
Yes, that does work, however seems a bit of a faf, having to create lots of groups, one for each extension at each site - that's not the problem
Inverted, this means you then cannot just call the bell extension on 244 - which I do sometimes for testing (connected to a Cisco ATA converter)
Paul
RE: iPECS 100 - Want additional extension to ring when call internally
www.jacksonvilletelephone.com
Jacksonville Florida Telephone Systems
RE: iPECS 100 - Want additional extension to ring when call internally
RE: iPECS 100 - Want additional extension to ring when call internally
The only way I can think of doing it would be to make a station (ring) group for each extension that contains the VoIP phone and the analog extension. You would then call the group number and it would ring both the phone and the bell. You would have to do this for every extension that you want to ring with the bell. It would not be pretty but would work.
www.jacksonvilletelephone.com
Jacksonville Florida Telephone Systems
RE: iPECS 100 - Want additional extension to ring when call internally