×
INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Contact US

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Students Click Here

upgraded nortel mics from 7.0 7.1xc using software and nvramr2 from another system.

upgraded nortel mics from 7.0 7.1xc using software and nvramr2 from another system.

upgraded nortel mics from 7.0 7.1xc using software and nvramr2 from another system.

(OP)
Nortel upgrade
to7.1xc software,dvram r2,combo card, 2 016mods. , After upgrade new mods accepted phones and working. No in or outbound calls on pri. Found my route settings had changed and now can call out, but no inbound calls. Have pri cheat sheet from this site,also nortel programing sheet. stumped. Jacktel

RE: upgraded nortel mics from 7.0 7.1xc using software and nvramr2 from another system.

Just a quick thought but disable PRI card and then re-enable in Hardware.

Double check:
Target Line Received Digits and Received Number Length match.

________________________________________

Add me to LinkedIN


=----(((((((((()----=
www.curlycord.com
Toronto, CAN

RE: upgraded nortel mics from 7.0 7.1xc using software and nvramr2 from another system.

(OP)
Curlycord
Tried that no joy can i ask about carrier codes in programing? what should they be? nothing in original carrier order sheet or in cheat sheet. Programing-,access codes,- carrier codes?

RE: upgraded nortel mics from 7.0 7.1xc using software and nvramr2 from another system.

(OP)
Update on post
Have meeting with carrier tech in Am but don't belive its their problem, still worried by route setting changes when moving from 7.0 fc to 7/1 xc software, except for standard settings for pri, I think im overlooking something basic. Received digits are 4 and target line id matches.I
will check alarm and event codes in Am,to many to list here as changes were made 1 by1 and returned to original setting ,have erased all codes to start fresh.
Jacktel

RE: upgraded nortel mics from 7.0 7.1xc using software and nvramr2 from another system.

(OP)
Jacktel
t-i PRI fine tech from lec verified, drove an hour to site for 8:00AM meet and he showed up at 10:30, Changed DTI card and still have same issue. Will go back again and replace Dvram card with same software tomorrow PM and se if there is some glitch from download. this particular upgrade is first problem one with Nortel Eq. I've ever had in 35 years doing installs.

RE: upgraded nortel mics from 7.0 7.1xc using software and nvramr2 from another system.

....we call that old age.
The guide does state not to install a used NVRAM, maybe one of rare cases why.

Thanks for updates, sorry couldn't help.

________________________________________

Add me to LinkedIN


=----(((((((((()----=
www.curlycord.com
Toronto, CAN

RE: upgraded nortel mics from 7.0 7.1xc using software and nvramr2 from another system.

(OP)
Jacktel
Back at clients 5:00PM. Feeling my age on this job Curlycord but still to mule headed to throw in towel.Understand about used NVRAM but except for XC software on EQ. Whole system parts pulled from same clients other office same setup, same circuit type and switch,and same carrier. Anyway decided to shutdown system and change NVRAM with a r3 one and restart,system would not boot so shut down and put original NVRAM in with same r7.1 xc software rebooted and after coming back up defaulted, entered PRI lic. code and did restore. Restore went fine and now needed to have Lec remove all trunk forwarding to analog fail over lines so i could check if DID calls would inbound properly. Customer service could not verify me as authorized so would not remove forward for test LOL. Done for the night. Still not sure if problem with original boot up or if corrupted software backed up. Calling Lec in a couple of min. for test. Curlycord will use your go to guy for remote access if needed thanks.

RE: upgraded nortel mics from 7.0 7.1xc using software and nvramr2 from another system.

(OP)
Update
Used a nortel pro recommended by Curlycord ,MYSUPPORTGUY.net and he had me disable DTI and reset slot as another type of card, wait and then reset slot back to DTI and program again. That did it. in early posts you will have seen that I defaulted system and also replaced DTI, So I never would have tried this as I have never had to do it before.
Thanks all
Jacktel

RE: upgraded nortel mics from 7.0 7.1xc using software and nvramr2 from another system.

I should have known that old trick sorry, been a couple years since doing that but I was on the right path....Path 0
lol

Thanks for update.

________________________________________

Add me to LinkedIN


=----(((((((((()----=
www.curlycord.com
Toronto, CAN

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members! Already a Member? Login


Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close