×
INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Contact US

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Students Click Here

Stacking x450-48p

Stacking x450-48p

Stacking x450-48p

(OP)
I have a site with 2 x X450's stacked using the cables all is ok and in and working.

the customer wants to add another, can i just add this to the next port in the stack and power up the switch, will this auto configure as switch 3 or will the whole stack need to be rebooted?

Regards

ACA - IP Office
ACS - IP Office
ACSS-SME

 

RE: Stacking x450-48p

(OP)
its ok found what i need

ACA - IP Office
ACS - IP Office
ACSS-SME

 

RE: Stacking x450-48p

you can add the new node to the stack, but it will not be active in the topology. you will need to push the stacking configuration out to the new node from the master and then reboot the new node (not the whole stack)

I hate all Uppercase... I don't want my groups to seem angry at me all the time! =)
- ColdFlame (vbscript forum)

RE: Stacking x450-48p

(OP)
yes thats what i eventually found....thanks anyway

ACA - IP Office
ACS - IP Office
ACSS-SME

 

RE: Stacking x450-48p

(OP)
did this all worked a treat

ACA - IP Office
ACS - IP Office
ACSS-SME

 

RE: Stacking x450-48p

Hi , I have just added two new nodes to an existing stack, can you explain how you push out the config from the master? I have added them to the stack as nodes 5 and 6 but I cannot use the switches. If i do show stack they are listed as active with the correct slot number, this is what I have done so far;

Connected them in with stacking cables and powered on.
Logged into the core

enable stacking node-address **:**:**:**:**:**
reboot node-address **:**:**:**:**:**
config stact node **:**:**:**:**:** slot-number 5
reboot node-address **:**:**:**:**:**

If i do the show stack command I get;
Node MAC Address    Slot  Stack State  Role     Flags
------------------  ----  -----------  -------  ---
*00:04:96:36:**:**  1     Active       Master   CA-
 00:04:96:36:**:**  2     Active       Backup   CA-
 00:04:96:36:**:**  3     Active       Standby  CA-
 00:04:96:36:**:**  4     Active       Standby  CA-
 00:04:96:51:**:**  5     Active       <none>   CA-
 00:04:96:51:**:**  6     Active       <none>   CA-

(5 and 6 being the new nodes).

Any help would be much appreciated.

Ta
STu

 

RE: Stacking x450-48p

Hi motox2k,

Have you synchronized the config with the
"synchronize stacking node-address 00:04:96:51:**:**" command to the new node and reboot the node?

Also check your license-level on the nodes.

You can find the manual to add a new node to the stack on page 176 in the ExtremeXOS Concepts Guide(v12.5).

Hope it helps!

br dabe612

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members! Already a Member? Login

Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close