Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!
  • Students Click Here

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Students Click Here

Configure VLAN routing on 5406zl

Configure VLAN routing on 5406zl

Configure VLAN routing on 5406zl

Hello All,
I am trying to route all traffic on our garage vlan "VLAN120" through to our office vlan "VLAN100" but it must route internally on the 5406zl
 at present all traffic for the network goes out through "Interface A1" around the MPLS to our old head office and then back via "A2 Interface" (100Mb LES (EES100) and then talks to our network.  The reason for this is historical but this will enable me to change it.  I am just not sure how to go about this.

I have copied in the switch config below.

hostname "SW1"

module 1 type J8702A
module 2 type J8702A
module 3 type J8706A

interface C23
   lacp Passive
interface C24
   lacp Passive
interface A1
   name "MPLS Connection"
interface A2
   name "100Mb LES"
   speed-duplex 100-full

trunk C1-C2 Trk1 Trunk
trunk C3-C4 Trk2 Trunk
trunk C5-C6 Trk3 Trunk
trunk C7-C8 Trk4 Trunk
trunk C11-C12 Trk6 Trunk
trunk C13-C14 Trk7 Trunk
trunk C9-C10 Trk5 Trunk

ip default-gateway

sntp server
timesync sntp
sntp unicast
sntp 30

vlan 1
   name "DEFAULT_VLAN"
   untagged C15-C24,Trk1-Trk7
   no untagged A1-A24,B1-B24
   no ip address

vlan 100
   name "Office"
   untagged A2-A3,A5-A24,B1-B24
   ip helper-address
   ip address
   tagged Trk1-Trk7

vlan 120
   name "Garage"
   untagged A1
   ip helper-address
   ip address
   tagged Trk1-Trk7

vlan 101
   name "Phone"
   untagged A4
   ip address
   tagged Trk1-Trk7

fault-finder bad-driver sensitivity high
fault-finder bad-transceiver sensitivity high
fault-finder bad-cable sensitivity high
fault-finder too-long-cable sensitivity high
fault-finder over-bandwidth sensitivity high
fault-finder broadcast-storm sensitivity high
fault-finder loss-of-link sensitivity high
fault-finder duplex-mismatch-HDx sensitivity high
fault-finder duplex-mismatch-FDx sensitivity high

qos type-of-service diff-services

spanning-tree Trk1 priority 4
spanning-tree Trk2 priority 4
spanning-tree Trk3 priority 4
spanning-tree Trk4 priority 4
spanning-tree Trk5 priority 4
spanning-tree Trk6 priority 4
spanning-tree Trk7 priority 4
spanning-tree config-name "elbg"
spanning-tree config-revision 1
spanning-tree instance 2 vlan 100
spanning-tree instance 3 vlan 120
spanning-tree instance 4 vlan 101
spanning-tree priority 1


RE: Configure VLAN routing on 5406zl

To route between VLANs all you need is the statement
"ip routing" in you config which I did not see. This will turn on routing between your internal VLANs you have defined onyour switch.

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members! Already a Member? Login

Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close