How to add 3 more lines to the existing 2 How to add 3 more lines to the existing 2 lumidapri (IS/IT--Management) (OP) 17 Jul 07 17:56 I get to the adm> prompt, but then i'm lost.I do have the worksheets and the programming manual but can't figure out how to display or to add 3 more lines RE: How to add 3 more lines to the existing 2 lumidapri (IS/IT--Management) (OP) 17 Jul 07 17:57 the system is STSe RE: How to add 3 more lines to the existing 2 ravnz5 (Vendor) 18 Jul 07 09:57 More info is needed. Are these POTS lines or are you working off of a t1 circuit card for your dial tones? I would think because of the amount of lines on the system that you are working with POTS lines. Please respond so that I may be able to help. Normally you would go into flash 40 for c.o. line programming. Enter the line numbers 001-004 to program for 4 lines. Make sure they are not disabled for out going calls:Attendant Disable Outgoing CO LineDescriptionThe first Attendant can disable CO lines to prevent outgoing access to those lines. This isuseful for removing a faulty line from service or for reserving CO lines for important use. Allstations that normally make calls on the lines are affected, but incoming calls are unaffected.A CO line may be disabled while it is being used. When the trunk becomes idle, furtheroutgoing access is prevented.OperationTo disable CO Lines:1. Lift handset or press ON/OFF button.2. Dial  on the dial pad. A confirmation tone sounds.3. Press the line button(s) of the CO Line(s) to disable. A confirmation tone sounds and theCO Line button(s) LED flashes.To reactivate the CO Line(s): Repeat Steps 1-3 to disable this feature.Calls may be transferred to internal stations only. An attempt to transfer a calloff-net (via a speed dial bin) results in the call recalling upon going on-hook. We all need a little help once in awhile. Tony the Phoneman.. RE: How to add 3 more lines to the existing 2 ravnz5 (Vendor) 18 Jul 07 10:04 you may need another line card to get the 5th line. We all need a little help once in awhile. Tony the Phoneman.. RE: How to add 3 more lines to the existing 2 lumidapri (IS/IT--Management) (OP) 18 Jul 07 14:04 Thank You, I got most of it working.The lines were pot lines and had to be activated as line group 1.However I still did not figure how to make lines 003-005 to show like line 001-002:CO 002------PRESET FORWARD DEST - H450 #### ####PRESET FWD VMID -0UNIVERSAL DAY ANSWER - DISABLEDthey still show:CO 003------PRESET FORWARD DEST - #### #### ####PRESET FWD VMID -NONEUNIVERSAL DAY ANSWER - DISABLED;from the pc I would key in:,(FLASH) THEN...? RE: How to add 3 more lines to the existing 2 ravnz5 (Vendor) 18 Jul 07 14:57 Look at Flexible Button Programming and assign the next 3 co line keys as co3,4,5. Flash 40 for thr ringing options:The Digital Telephone has 24 flexible buttons that can be programmed.24-BUTTON DEFAULT:Use Flash 50 programming when you want to modify a range of stations’ attributes usingfixed station numbers.Use Flash 51 programming to modify a single station’s attributes using a flexible stationnumber.Programming Steps1. Press FLASH and dial  or dial . Flexible button #24 (New Range) is lit and one ofthe following messages displays:2. Enter the range of fixed station numbers (100-149) to be programmed. If only one stationis being programmed, enter that number twice, e.g., [100 100].-or-Enter a valid flexible number (100-8999) to be programmed.STA 100 STA 101 STA 102 STA 103?? 1 Q ?? 2 W ?? 3 E ?? 4 RSTA 104 STA 105 STA 106 STA 107?? 5 T ?? 6 Y ?? 7 U ?? 8 ISTA 108 STA 109 STA 110 STA 111?? 9 O ?? 10 P ?? 11 A ?? 12 SCO 1 CO 2 CO 3 CO 4?? 13 D ?? 14 F ?? 15 G ?? 16 HCO 5 CO 6 LOOP POOL?? 17 J ?? 18 K ?? 19 L ?? 20 :CALL BACK PICKUP DND LINE QUEUE?? 21 Z ?? 22 X ?? 23 C ?? 24 VFlash 50 - Fixed Numbers Flash 51 - Flexible NumbersSTATION ATTRIBUTESSELECT A STATION RANGEENTER STATION NUMBERIf HOLD is pressed without entering a station range, all stations are selected.Flexible Button Function Assignment 2-165Features and OperationSTARPLUS STSe - Programming & Operations Manual August 20053. Press HOLD to save the entry. A confirmation tone sounds and the display updates.Flexible button #19 is lit. The display updates to reflect current programming for Page A:4. Press button #20. The display updates to reflect current programming for Page B.5. Press the BUTTON ASSIGN flexible button (Button #11). The following message displays:6. Enter a valid button number [01-24] to program, the desired function code (0-4 or #) plusany related information (e.g., CO line number if assigning a CO Line button), and thenpress HOLD.Function Codes = Flexible/user changeable = CO line = Loop button/all-purpose CO appearance = Pool for specific groups = Direct feature programmable[#] = Locks buttonTo assign a Flexible Button (user programmable):Enter [BB], , [HOLD]BB = Desired Flexible Button NumberWhen a button is assigned as a flexible button , the user can program any features orfunctions to which they have access on the buttons.Flash 50 - Fixed Numbers Flash 51 - Flexible NumbersXXX - XXX PAGE AENTER BUTTON NUMBERSXXX PAGE AENTER BUTTON NUMBERXXX-XXX = fixed station range XXX = 3- or 4-digit flexible numberFlash 50 - Fixed Numbers Flash 51 - Flexible NumbersXXX - XXX PAGE BENTER BUTTON NUMBERSXXX PAGE BENTER BUTTON NUMBERXXX-XXX = fixed station range XXX = 3- or 4-digit flexible numberFLEX BUTTON PROGENTER BUTTON DATA We all need a little help once in awhile. Tony the Phoneman.. RE: How to add 3 more lines to the existing 2 ravnz5 (Vendor) 18 Jul 07 15:04 To assign a CO Line Button:Enter [BB], , [LLL], [HOLD]BB = Desired Flexible Button NumberLLL = CO Line NumberButtons assigned as specific CO lines provide direct access and appearance of the CO lineat a station. The station receives call status indications such as LED flash rates forincoming ringing when the line is placed on HOLD, etc. CO Line ringing is programmed inCO Line Attribute programming. We all need a little help once in awhile. Tony the Phoneman..