×
INTELLIGENT WORK FORUMS
FOR COMPUTER PROFESSIONALS

Contact US

Log In

Come Join Us!

Are you a
Computer / IT professional?
Join Tek-Tips Forums!
  • Talk With Other Members
  • Be Notified Of Responses
    To Your Posts
  • Keyword Search
  • One-Click Access To Your
    Favorite Forums
  • Automated Signatures
    On Your Posts
  • Best Of All, It's Free!

*Tek-Tips's functionality depends on members receiving e-mail. By joining you are opting in to receive e-mail.

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

Students Click Here

KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

(OP)
Hi all!

I wonder if anyone can help me on this as it's driving me nuts!

I have replaced the main KXTD181 analogue line board in our 1232 with a KXTD281E BRI line card. There were several reasons for doing this, but two of the main ones were so as to get CLIP (caller ID) and DDI.

I have had CLIP enabled on the line, but incoming calls do not show the CLIP on an extension when ringing.

I've made sure that the calling party isn't witholding their number, etc, but no joy. Anyone have any ideas?

The system doesn't seem to allow for the programming of DDI settings either (the programming codes don't exist on this unit).

Has anyone had any experience with a version 2 unit and CLIP / DDI? Any help greatly appreciated!

RE: KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

Update the software and it will give you the correct options

RE: KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

(OP)
Thanks, but that isn't my question. I know that I can upgrade the unit to a version 4 EPROM, but I want to know if anyone has managed to get these options to work on a version 2 box. Updating the motherboard can only be done at an additional cost!  

RE: KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

i don't think ver 2 supported clip or clid!

RE: KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

(OP)
Okay, fair enough. Thanks for the info both of you. I'll have to see about upgrading the box then!

RE: KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

hey a note we don't have bri available over here in
the us of a but you can bet that if the options that you
are looking for do not show up in your programing utility
then you can bet that it is not supported!!

RE: KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

(OP)
Didn't realise BRI wasn't available over there. Thanks again for the info. I've put an enquiry into Panasonic support to see what they say about a chip upgrade.

RE: KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

wavey were are you located?

RE: KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

(OP)
The UK..

RE: KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

Hi, send me backup of your program so I can give you a solution.Bay Damir
servis@coins-com.hr

RE: KXTD1232 Version 2 and CLIP / DDI (MSN) on BRI

i cant say why the clip is not working if you can get your hands on a isdn modem with software this will tell you if it is being sent by your supplier.
as for the ddi it is on the ver 2 however you need the ver 2 doss software to programe... the ddi location on the ver3 software lets you program the ddi and save them but when you reload the system they are gone again (useing the v2 software go to
station settings 2
you will see the list of exts & names on screen with a space before each... this space is listed on screen as msn no:
place your ddi here only 1 ddi to each ext & you cannot seta ddi  to a grp
if you need ddi to a grp point ddi to a ext then forward the ext all calls to the grp

                  hope this helps a bit

Red Flag This Post

Please let us know here why this post is inappropriate. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Red Flag Submitted

Thank you for helping keep Tek-Tips Forums free from inappropriate posts.
The Tek-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Tek-Tips forums is a member-only feature.

Click Here to join Tek-Tips and talk with other members! Already a Member? Login


Close Box

Join Tek-Tips® Today!

Join your peers on the Internet's largest technical computer professional community.
It's easy to join and it's free.

Here's Why Members Love Tek-Tips Forums:

Register now while it's still free!

Already a member? Close this window and log in.

Join Us             Close