Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Xpressions voicemail won't pickup

Status
Not open for further replies.

John Trujillo

IS-IT--Management
May 7, 2019
15
US
Hi I have inherited a Siemens Hipath 4000 v.30. The system uses Xpressions v.3 voicemail. As of late the voicemail will not pickup. All you get is a busy signal. Any and all help would be most welcome. Thank you.
 
So when you dial the extension to get your voicemail, that's when you get the busy? It could be anything from the Xpressions server being dead to a trunk issue. There are a lot of versions and implementations of Xpressions. Your best bet is to go check on the health of the Xpressions server first. Since it's already dead, a reboot couldn't hurt it any worse!

LoPath
Maintain HiPath 4000 V5 & V6, OpenScape Xpert V4 & V6, OpenScape Xpressions V7, OpenScape Contact Center V8, OpenScape Voice V9
 
The xpressions server is up and running. It is running xpressions v3. I have reinstalled expressions and updated the drivers on the diva cards.The system took a power hit a month ago and I have been following these tek tips. Xpressions is using trunk 4. I agree it could be anything but maybe you could give me a list to start narrowing down that"it could be anything".
 
The power hit could have taken out your interface board.
Have you dis a DIS-SDSU,,ALL,PEN,PER3; (it will ask you for the PEN) to see if your trunk is up? It may be in a defect mode and need to be reset.
When you call the voicemail, do your display phones have a message like "Please Try Later" or something like that?



Don Bruechert, Voice Comm Analyst II
CareTech Solutions @ Holy Family Memorial
Manitowoc, WI, USA
 
DIS-SDSU:ALL,,PEN,PER3,1,1,55,0;
H500: AMO SDSU STARTED

LTG1 (PERIPHERY)
------
MOUNTING LOCATION MODULE NAME BDL BD(#=ACT) STATUS
------------------- LTG 1 --------------------- READY
-LTUW---------SG 1 LTU 1 --------------------- READY
** .LTG 1.LTU 1.055 STMD2 A Q2163-X READY
CCT LINE STNO SI BUS TYPE
000 1549 PP NW READY
MULTLINE 3. . . . . . . . . . . . . . .READY
000 NO CONN
001 NETWORK SUBUNIT . TMD CONN ISDN READY
(ALT_ROUT: N) (S0CONN )
LINE: 1549 STNO: SI:
001 . . . . . . . . TMD CONN ISDN READY
002 NETWORK SUBUNIT . TMD CONN ISDN READY
(ALT_ROUT: N) (S0CONN )
LINE: 1549 STNO: SI:
001 . . . . . . . . TMD CONN ISDN READY
I have been following the threads and learning and this is what makes this so maddening. Things say they are ready but all I get is a busy signal an nothing else.

 
+------------------------------- FORMAT = L -----------------------------------+
| TGRP NUMBER : 1 TGRP NAME : QWEST LOCAL PRI MAXIMUM NO. : 23 |
| CHARCON : NEUTRAL |
| SUBGROUP NO.: 13 DEVICE TYPE : S1COD TRACENO : 0 |
| SEARCH MODE : DESCENDING ACD THRESHOLD : * |
| NUMBER OF ASSOCIATED ROUTES : 7 PRIORITY : 1 |
| TDDRFLAG : OFF TDDRTHRESHOLD: SOURCEGROUPIDX : 1 |
| GDTRRULE : 0 ACDPMGRP : 0 |
| THE FOLLOWING TRUNKS (LTG-LTU-SLOT-CCT) HAVE BEEN ALLOCATED: |
+------------------------------------------------------------------------------+
| 1- 3-103-0 1 | 1- 3-103-0 2 | 1- 3-103-0 3 |
| 1- 3-103-0 4 | 1- 3-103-0 5 | 1- 3-103-0 6 |
| 1- 3-103-0 7 | 1- 3-103-0 8 | 1- 3-103-0 9 |
| 1- 3-103-0 10 | 1- 3-103-0 11 | 1- 3-103-0 12 |
| 1- 3-103-0 13 | 1- 3-103-0 14 | 1- 3-103-0 15 |
| 1- 3-103-0 16 | 1- 3-103-0 17 | 1- 3-103-0 18 |
| 1- 3-103-0 19 | 1- 3-103-0 20 | 1- 3-103-0 21 |
| 1- 3-103-0 22 | 1- 3-103-0 23 | |
+------------------------------------------------------------------------------+

+------------------------------- FORMAT = L -----------------------------------+
| TGRP NUMBER : 3 TGRP NAME : DID FAX SERVER MAXIMUM NO. : 2 |
| CHARCON : NEUTRAL |
| SUBGROUP NO.: 2 DEVICE TYPE : - TRACENO : 0 |
| SEARCH MODE : CIRCULAR ACD THRESHOLD : 0 |
| NUMBER OF ASSOCIATED ROUTES : 0 PRIORITY : 1 |
| TDDRFLAG : ON TDDRTHRESHOLD: 0 |
| GDTRRULE : 0 ACDPMGRP : 0 |
+------------------------------------------------------------------------------+

+------------------------------- FORMAT = L -----------------------------------+
| TGRP NUMBER : 4 TGRP NAME : XPRESSIONS MAXIMUM NO. : 16 |
| CHARCON : NEUTRAL |
| SUBGROUP NO.: 3 DEVICE TYPE : S0CONN TRACENO : 0 |
| SEARCH MODE : CIRCULAR ACD THRESHOLD : * |
| NUMBER OF ASSOCIATED ROUTES : 3 PRIORITY : 5 |
| TDDRFLAG : OFF TDDRTHRESHOLD: SOURCEGROUPIDX : 1 |
| GDTRRULE : 0 ACDPMGRP : 0 |
| THE FOLLOWING TRUNKS (LTG-LTU-SLOT-CCT) HAVE BEEN ALLOCATED: |
+------------------------------------------------------------------------------+
| 1- 1- 55-0 1 | 1- 1- 55-0 2 | 1- 1- 55-1 1 |
| 1- 1- 55-1 2 | 1- 1- 55-2 1 | 1- 1- 55-2 2 |
| 1- 1- 55-3 1 | 1- 1- 55-3 2 | 1- 1- 55-4 1 |
| 1- 1- 55-4 2 | 1- 1- 55-5 1 | 1- 1- 55-5 2 |
| 1- 1- 55-6 1 | 1- 1- 55-6 2 | 1- 1- 55-7 1 |
| 1- 1- 55-7 2 | | |
+------------------------------------------------------------------------------+

+------------------------------- FORMAT = L -----------------------------------+
| TGRP NUMBER : 7 TGRP NAME : QWEST LD PRI MAXIMUM NO. : 23 |
| CHARCON : NEUTRAL |
| SUBGROUP NO.: 12 DEVICE TYPE : S1COD TRACENO : 0 |
| SEARCH MODE : DESCENDING ACD THRESHOLD : * |
| NUMBER OF ASSOCIATED ROUTES : 3 PRIORITY : 1 |
| TDDRFLAG : OFF TDDRTHRESHOLD: SOURCEGROUPIDX : 1 |
| GDTRRULE : 0 ACDPMGRP : 0 |
| THE FOLLOWING TRUNKS (LTG-LTU-SLOT-CCT) HAVE BEEN ALLOCATED: |
+------------------------------------------------------------------------------+
| 1- 3- 61-1 1 | 1- 3- 61-1 2 | 1- 3- 61-1 3 |
| 1- 3- 61-1 4 | 1- 3- 61-1 5 | 1- 3- 61-1 6 |
| 1- 3- 61-1 7 | 1- 3- 61-1 8 | 1- 3- 61-1 9 |
| 1- 3- 61-1 10 | 1- 3- 61-1 11 | 1- 3- 61-1 12 |
| 1- 3- 61-1 13 | 1- 3- 61-1 14 | 1- 3- 61-1 15 |
| 1- 3- 61-1 16 | 1- 3- 61-1 17 | 1- 3- 61-1 18 |
| 1- 3- 61-1 19 | 1- 3- 61-1 20 | 1- 3- 61-1 21 |
| 1- 3- 61-1 22 | 1- 3- 61-1 23 | |
+------------------------------------------------------------------------------+

+------------------------------- FORMAT = L -----------------------------------+
| TGRP NUMBER : 102 TGRP NAME : CORNET-NQ CISCO MAXIMUM NO. : 23 |
| CHARCON : NEUTRAL |
| SUBGROUP NO.: 11 DEVICE TYPE : S1CONN TRACENO : 0 |
| SEARCH MODE : ASCENDING ACD THRESHOLD : * |
| NUMBER OF ASSOCIATED ROUTES : 1 PRIORITY : 2 |
| TDDRFLAG : ON TDDRTHRESHOLD: 2 SOURCEGROUPIDX : 1 |
| GDTRRULE : 0 ACDPMGRP : 0 |
| THE FOLLOWING TRUNKS (LTG-LTU-SLOT-CCT) HAVE BEEN ALLOCATED: |
+------------------------------------------------------------------------------+
| 1- 3- 61-0 1 | 1- 3- 61-0 2 | 1- 3- 61-0 3 |
| 1- 3- 61-0 4 | 1- 3- 61-0 5 | 1- 3- 61-0 6 |
| 1- 3- 61-0 7 | 1- 3- 61-0 8 | 1- 3- 61-0 9 |
| 1- 3- 61-0 10 | 1- 3- 61-0 11 | 1- 3- 61-0 12 |
| 1- 3- 61-0 13 | 1- 3- 61-0 14 | 1- 3- 61-0 15 |
| 1- 3- 61-0 16 | 1- 3- 61-0 17 | 1- 3- 61-0 18 |
| 1- 3- 61-0 19 | 1- 3- 61-0 20 | 1- 3- 61-0 21 |
| 1- 3- 61-0 22 | 1- 3- 61-0 23 | |
+------------------------------------------------------------------------------+
ADDRESS : LTG 1 LTU 1 SOURCE GROUP 1 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
19 | Q2468-X RG-USA 0| | Q2468-X | 1 - | READY
25 | Q2246-X SLMA24 A 0| | Q2246-X | 1 -05 - | READY
31 | Q2158-X SLMO24 1 A 0| | Q2158-X | 1 -05 - | READY
37 | Q2158-X SLMO24 1 A 0| | Q2158-X | 1 -05 - | READY
43 | Q2158-X SLMO24 1 A 0| | Q2158-X | 1 -05 - | READY
49 | Q2303-X10 STMI 1 A 0| | Q2303-X10 | 1 -05 - | READY
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : 10. 1.120.103 B-CHANNELS : 30 BCHLCNT : 30
+--------------------------------+-+------------+------------+------------
55 | Q2163-X STMD2 1 A 0| | Q2163-X | 1 -10 - | READY
61 | Q2192-X TMDNH 2 A 0| | Q2192-X | 1 D504-C | READY
67 | Q2303-X20 STMI-HFA 3 A 0| | Q2303-X20 | 1 -04 - | READY
73 | Q2166-X LTUCX 0| | Q2166-X | 1 -07 - | READY
79 | Q2192-X TMDNH 2 A 0| | Q2192-X | 1 D504-C | READY
85 | AVAILABLE 0| | AVAILABLE | |
91 | AVAILABLE 0| | AVAILABLE | |
97 | Q2168-X SLMO24 1 A 0| | Q2168-X | 1 -08 - | READY
103 | Q2303-X20 STMI-HFA 3 A 0| | Q2303-X20 | 1 -04 - | READY
109 | Q2168-X SLMO24 1 A 0| | Q2168-X | 1 -08 - | READY
115 | Q2158-X SLMO24 1 A 0| | Q2158-X | 1 -05 - | READY
121 | Q2246-X SLMA24 A 0| | Q2246-X | 1 -05 - | READY

ADDRESS : LTG 1 LTU 2 SOURCE GROUP 1 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
19 | Q2187-X SIUX2 2 0| | Q2187-X | 1 -02 - | READY
25 | Q2303-X20 STMI-HFA 3 A 0| | Q2303-X20 | 1 -02 - | READY
31 | Q2158-X SLMO24 1 A 0| | Q2158-X | 1 -05 - | READY
37 | Q2158-X SLMO24 1 A 0| | Q2158-X | 1 -05 - | READY
43 | Q2158-X SLMO24 1 A 0| | Q2158-X | 1 -05 - | READY
49 | Q2303-X10 STMI 1 A 0| | Q2303-X10 | 1 -05 - | READY
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : 10. 1.120.104 B-CHANNELS : 30 BCHLCNT : 30
+--------------------------------+-+------------+------------+------------
55 | Q2479-X SLMQ3 A 0| | Q2479-X | 1 -03 - | READY
61 | Q2192-X TMDNH 2 A 0| | Q2192-X | 1 D504-C | READY
67 | Q2303-X20 STMI-HFA 3 A 0| | Q2303-X20 | 1 -04 - | READY
73 | Q2166-X LTUCX 0| | Q2166-X | 1 -06 - | READY
79 | Q2192-X TMDNH 2 A 0| | Q2192-X | 1 D504-C | READY
85 | Q2168-X SLMO24 1 A 0| | Q2168-X | 1 -10 - | READY
91 | Q2303-X20 STMI-HFA 3 A 0| | Q2303-X20 | 1 -04 - | READY
97 | Q2158-X SLMO24 1 A 0| | Q2158-X | 1 -05 - | READY
103 | Q2158-X SLMO24 1 A 0| | Q2158-X | 1 -05 - | READY
109 | Q2158-X SLMO24 1 A 0| | Q2158-X | 1 -05 - | READY
115 | Q2158-X SLMO24 1 A 0| | Q2158-X | 1 -05 - | READY
121 | Q2158-X SLMO24 1 A 0| | Q2158-X | 1 -05 - | READY

ADDRESS : LTG 1 LTU 3 SOURCE GROUP 1 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
19 | AVAILABLE 0| | AVAILABLE | |
25 | Q2303-X20 STMI-HFA 3 A 0| | Q2303-X20 | 1 -04 - | READY
31 | Q2303-X20 STMI-HFA 3 A 0| | Q2303-X20 | 1 -04 - | READY
37 | AVAILABLE 0| | AVAILABLE | |
43 | AVAILABLE 0| | AVAILABLE | |
49 | AVAILABLE 0| | AVAILABLE | |
55 | AVAILABLE 0| | AVAILABLE | |
61 | Q2216-X DIU2U-M 6 A 0| | Q2216-X | 1 -06 - | READY
67 | Q2303-X20 STMI-HFA 3 A 0| | Q2303-X20 | 1 -04 - | READY
73 | Q2166-X LTUCX 0| | Q2166-X | 1 -09 - | READY
79 | Q2303-X20 STMI-HFA 3 A 0| | Q2303-X20 | 1 -04 - | READY
85 | Q2303-X20 STMI-HFA 3 A 0| | Q2303-X20 | 1 -04 - | READY
91 | Q2303-X20 STMI-HFA 3 A 0| | Q2303-X20 | 1 -04 - | READY
97 | Q2316-X STMI2HFA 3 A 0|*| UNKNOWN | | DEFECT
103 | Q2216-X DIU2U-M 6 A 0| | Q2216-X | 1 -06 - | READY
109 | AVAILABLE 0| | AVAILABLE | |
115 | AVAILABLE 0| | AVAILABLE | |
121 | Q2192-X TMDNH 1 A 0| | Q2192-X | 1 D504-C | READY

ADDRESS : LTG 1 LTU 17 SOURCE GROUP 17 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
1 | AVAILABLE 0| | AVAILABLE | |
2 | Q2246-X SLMA24 A 0| | Q2246-X | 1 -09 - | READY
3 | Q2168-X SLMO24 1 A 0| | Q2168-X | 1 -08 - | READY
4 | Q2302-X10 NCUI 1 0| | Q2302-X10 | 1 -04 - | READY
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : 10. 2. 10. 7 B-CHANNELS : 30 BCHLCNT : 30
+--------------------------------+-+------------+------------+------------
5 | AVAILABLE 0| | AVAILABLE | |
6 | Q2168-X SLMO24 1 A 0| | Q2168-X | 1 -10 - | READY
7 | Q2168-X SLMO24 1 A 0| | Q2168-X | 1 -10 - | READY
8 | Q2168-X SLMO24 1 A 0| | Q2168-X | 1 -F1 - | READY

ADDRESS : LTG 1 LTU 18 SOURCE GROUP 18 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
1 | AVAILABLE 0| | AVAILABLE | |
2 | Q2246-X SLMA24 A 0| | Q2246-X | 1 -09 - | READY
3 | Q2168-X SLMO24 1 A 0| | Q2168-X | 1 -08 - | READY
4 | Q2302-X10 NCUI 1 0| | Q2302-X10 | 1 -04 - | READY
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : 10. 3. 10. 8 B-CHANNELS : 30 BCHLCNT : 30
+--------------------------------+-+------------+------------+------------
5 | AVAILABLE 0| | AVAILABLE | |
6 | Q2168-X SLMO24 1 A 0|*| | | NPR
7 | Q2168-X SLMO24 1 A 0|*| | | NPR
8 | Q2168-X SLMO24 1 A 0|*| | | NPR

DIS-TDCSU:1-3-103-0;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S1COD PEN = 1-03-103-0 TGRP = 1 |
|---------------------------------------------------------------------------|
| PROTVAR = NI2 INS = Y SRCHMODE = DSC |
| COTNO = 101 COPNO = 101 DPLN = 0 |
| ITR = 0 COS = 1 LCOSV = 1 |
| LCOSD = 1 CCT = QWEST LOCAL DESTNO = 1 |
| SEGMENT = 1 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = 3 |
| TRTBL = GDTR SIDANI = Y ATNTYP = ISDN |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 101 FWDX = 1 |
| DOMTYPE = UNKNOWN DOMAINNO = 0 TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 0 |
| CLASSMRK = EC & G711 SRCGRP = 1 |
| TCCID = |
|---------------------------------------------------------------------------|
| BCNEG = N BCGR = 1 IGN = 0 |
| IID = 4 LWPAR = 2 |
| LWPP = LWLT = LWPS = |
| LWR1 = LWR2 = |
| SVCDOM = |
| BCHAN = 1 && 23 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 23
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S0CONN PEN = 1-01-055-0 TGRP = 4 |
|---------------------------------------------------------------------------|
| PROTVAR = PSS1V2 INS = Y SRCHMODE = CIR |
| COTNO = 91 COPNO = 91 DPLN = 0 |
| ITR = 0 COS = 90 LCOSV = 15 |
| LCOSD = 1 CCT = XPRESS DESTNO = 190 |
| SEGMENT = 8 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 190 |
| ALARMNO = 0 FIDX = 5 CARRIER = 1 |
| ZONE = EMPTY COTX = 91 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 0 |
| CLASSMRK = EC & G711 & G729 SRCGRP = 1 |
| TCCID = |
|---------------------------------------------------------------------------|
| MASTER = Y SMD = Y CNTRNR = 0 |
| BCNEG = N |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 2
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S1CONN PEN = 1-03-061-0 TGRP = 102 |
|---------------------------------------------------------------------------|
| PROTVAR = PSS1V2 INS = N SRCHMODE = ASC |
| COTNO = 102 COPNO = 102 DPLN = 0 |
| ITR = 0 COS = 102 LCOSV = 20 |
| LCOSD = 1 CCT = CORNETNQ DESTNO = 102 |
| SEGMENT = 1 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 102 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 102 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729OPT SRCGRP = |
| TCCID = QSIGCISCOVOIP |
|---------------------------------------------------------------------------|
| BCNEG = N BCGR = 1 LWPAR = 1 |
| LWPP = LWLT = LWPS = |
| LWR1 = LWR2 = |
| DMCALLWD = DMCSEC = VNNO = |
| SVCDOM = |
| BCHAN = 1 && 23 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 23

 
Here is a trace:
**** Local config (date: 08 May 2019, 08:32:41) - BEGIN ****

[APPL1]
Type=RAS
RasInstanceId=0
NoAnswerTimeout=20
IgnoreCbNumber=0
ForceAnalogBcOnCb=0
L2Protocol=0
L2ProtocolSpeed=64000
ShortholdMode=0
ShortholdTime=0
AuthProtocol=0
AuthTimeout=0
SecurityLevel=0
NumberChecking=0
GUIReserved=017F0000007F0000000000000000000000000000

[APPL2]
Type=CAPI
ControllerStart=1
ControllerCount=8
GroupOptimization=0
GUIReserved=01C7000000C70000000000000000000000000000

[CARD1]
CardName=Eicon Diva Server 4BRI-8M 2.0 (PCI)
CardType=53
BusType=5
Lines=4
LinesIDI=4
SerialNumber=11841
DspCount=8
ComponentId=Siemens Cornet-N
CardStatus=0
IsdnSwitchTypes=29694
ICIInstance=0008
GUIReserved=01D3000000D300000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000

[CARD2]
CardName=Eicon Diva Server 4BRI-8M 2.0 (PCI) #2
CardType=53
BusType=5
Lines=4
LinesIDI=4
SerialNumber=11845
DspCount=8
ComponentId=Siemens Cornet-N
CardStatus=0
IsdnSwitchTypes=29694
ICIInstance=0009
GUIReserved=019E0100009E01000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000

[LINE1]
LineType=0
LinePool=0
GUIReserved=0000000000000000000000000000000000000000
NumberType=2
NumberLen=4
AccumulateExtensionIn=0
MSN=
RangeLow=1000
RangeHigh=2999
PcCfg1=P=0x4a Y 0
PcCfg2=P=0x4f Y 0
PcCfg3=P=0x35 Y 0
PcCfg4=P=0x2c D 0
PcCfg5=P=0x30 B 0x00
PcCfg6=P=0x37 D 0
PcCfg7=P=0x39 D 0
PcCfgMtpx1=W="Cfg\Ctrl\ECT\Emulation" Y 0
Protocol=CORNET-N
GenerateRingtone=0
AutoSpid=0
SpidMode=3
ForceAlert=0
AddToConference=0
RemoveFromConference=0
MessageWaiting=0
CallTransfer=0
CallAppearances=0
ElectronicKeyTouchSystem=0
DisplayValAs=10
EnableLayer1Tristate=0
DeviceMode=0
PbxType=10
CallRefFormat=0
ChannelIdentifierFormat=0
ChannelAssignment=0
QSigStandard=4
InterfaceType=1
Point2Point=1
TEI=0
L2Mode=1
LeasedLineMode=0
CodeVariant=0
CRCMode=0
Role=0
RBSDID=1
RBSGlaResPa=1
RBSBearerCapability=4
RBSAnswerDelay=120
RBSrxDigitTimeOut=10
RBSStart=0
RbsAnswerSupervision=0
RbsSpecialAccess=0
RBSDial=1
BChnCnt=0
ForceLaw=0
FractionalLine=0
LowChannel=0
R2Dialect=0
R2CTryLength=-1
R2CliReq=1
BChnMask=0
NoHscx30=0
NumTEIs=1
Part68Limiter=0
ECTTransferType=0
DiscOnProgress=0
RoutingAccessAuthor=0
QSigPathReplaceInvite=0
QSigTranspFacility=0
QSigRerouting=1
MsgWaitingMode=0
CallDeflection=0
RdnEmulation=0
ECTLinkBalance=0
CallTransferMode=0
ReroutingOptimization=0
CollectTimeout=0

[LINE2]
LineType=0
LinePool=0
GUIReserved=0000000000000000000000000000000000000000
NumberType=2
NumberLen=4
AccumulateExtensionIn=0
MSN=
RangeLow=1000
RangeHigh=2999
PcCfg1=P=0x4a Y 0
PcCfg2=P=0x4f Y 0
PcCfg3=P=0x35 Y 0
PcCfg4=P=0x2c D 0
PcCfg5=P=0x30 B 0x00
PcCfg6=P=0x37 D 0
PcCfg7=P=0x39 D 0
PcCfgMtpx1=W="Cfg\Ctrl\ECT\Emulation" Y 0
Protocol=CORNET-N
GenerateRingtone=0
AutoSpid=0
SpidMode=3
ForceAlert=0
AddToConference=0
RemoveFromConference=0
MessageWaiting=0
CallTransfer=0
CallAppearances=0
ElectronicKeyTouchSystem=0
DisplayValAs=10
EnableLayer1Tristate=0
DeviceMode=0
PbxType=10
CallRefFormat=0
ChannelIdentifierFormat=0
ChannelAssignment=0
QSigStandard=4
InterfaceType=1
Point2Point=1
TEI=0
L2Mode=1
LeasedLineMode=0
CodeVariant=0
CRCMode=0
Role=0
RBSDID=1
RBSGlaResPa=1
RBSBearerCapability=4
RBSAnswerDelay=120
RBSrxDigitTimeOut=10
RBSStart=0
RbsAnswerSupervision=0
RbsSpecialAccess=0
RBSDial=1
BChnCnt=0
ForceLaw=0
FractionalLine=0
LowChannel=0
R2Dialect=0
R2CTryLength=-1
R2CliReq=1
BChnMask=0
NoHscx30=0
NumTEIs=1
Part68Limiter=0
ECTTransferType=0
DiscOnProgress=0
RoutingAccessAuthor=0
QSigPathReplaceInvite=0
QSigTranspFacility=0
QSigRerouting=1
MsgWaitingMode=0
CallDeflection=0
RdnEmulation=0
ECTLinkBalance=0
CallTransferMode=0
ReroutingOptimization=0
CollectTimeout=0

[LINE3]
LineType=0
LinePool=0
GUIReserved=0000000000000000000000000000000000000000
NumberType=2
NumberLen=4
AccumulateExtensionIn=0
MSN=
RangeLow=1000
RangeHigh=2999
PcCfg1=P=0x4a Y 0
PcCfg2=P=0x4f Y 0
PcCfg3=P=0x35 Y 0
PcCfg4=P=0x2c D 0
PcCfg5=P=0x30 B 0x00
PcCfg6=P=0x37 D 0
PcCfg7=P=0x39 D 0
PcCfgMtpx1=W="Cfg\Ctrl\ECT\Emulation" Y 0
Protocol=CORNET-N
GenerateRingtone=0
AutoSpid=0
SpidMode=3
ForceAlert=0
AddToConference=0
RemoveFromConference=0
MessageWaiting=0
CallTransfer=0
CallAppearances=0
ElectronicKeyTouchSystem=0
DisplayValAs=10
EnableLayer1Tristate=0
DeviceMode=0
PbxType=10
CallRefFormat=0
ChannelIdentifierFormat=0
ChannelAssignment=0
QSigStandard=4
InterfaceType=1
Point2Point=1
TEI=0
L2Mode=1
LeasedLineMode=0
CodeVariant=0
CRCMode=0
Role=0
RBSDID=1
RBSGlaResPa=1
RBSBearerCapability=4
RBSAnswerDelay=120
RBSrxDigitTimeOut=10
RBSStart=0
RbsAnswerSupervision=0
RbsSpecialAccess=0
RBSDial=1
BChnCnt=0
ForceLaw=0
FractionalLine=0
LowChannel=0
R2Dialect=0
R2CTryLength=-1
R2CliReq=1
BChnMask=0
NoHscx30=0
NumTEIs=1
Part68Limiter=0
ECTTransferType=0
DiscOnProgress=0
RoutingAccessAuthor=0
QSigPathReplaceInvite=0
QSigTranspFacility=0
QSigRerouting=1
MsgWaitingMode=0
CallDeflection=0
RdnEmulation=0
ECTLinkBalance=0
CallTransferMode=0
ReroutingOptimization=0
CollectTimeout=0

[LINE4]
LineType=0
LinePool=0
GUIReserved=0000000000000000000000000000000000000000
NumberType=2
NumberLen=4
AccumulateExtensionIn=0
MSN=
RangeLow=1000
RangeHigh=2999
PcCfg1=P=0x4a Y 0
PcCfg2=P=0x4f Y 0
PcCfg3=P=0x35 Y 0
PcCfg4=P=0x2c D 0
PcCfg5=P=0x30 B 0x00
PcCfg6=P=0x37 D 0
PcCfg7=P=0x39 D 0
PcCfgMtpx1=W="Cfg\Ctrl\ECT\Emulation" Y 0
Protocol=CORNET-N
GenerateRingtone=0
AutoSpid=0
SpidMode=3
ForceAlert=0
AddToConference=0
RemoveFromConference=0
MessageWaiting=0
CallTransfer=0
CallAppearances=0
ElectronicKeyTouchSystem=0
DisplayValAs=10
EnableLayer1Tristate=0
DeviceMode=0
PbxType=10
CallRefFormat=0
ChannelIdentifierFormat=0
ChannelAssignment=0
QSigStandard=4
InterfaceType=1
Point2Point=1
TEI=0
L2Mode=1
LeasedLineMode=0
CodeVariant=0
CRCMode=0
Role=0
RBSDID=1
RBSGlaResPa=1
RBSBearerCapability=4
RBSAnswerDelay=120
RBSrxDigitTimeOut=10
RBSStart=0
RbsAnswerSupervision=0
RbsSpecialAccess=0
RBSDial=1
BChnCnt=0
ForceLaw=0
FractionalLine=0
LowChannel=0
R2Dialect=0
R2CTryLength=-1
R2CliReq=1
BChnMask=0
NoHscx30=0
NumTEIs=1
Part68Limiter=0
ECTTransferType=0
DiscOnProgress=0
RoutingAccessAuthor=0
QSigPathReplaceInvite=0
QSigTranspFacility=0
QSigRerouting=1
MsgWaitingMode=0
CallDeflection=0
RdnEmulation=0
ECTLinkBalance=0
CallTransferMode=0
ReroutingOptimization=0
CollectTimeout=0

[LINE5]
LineType=0
LinePool=0
GUIReserved=0000000000000000000000000000000000000000
NumberType=2
NumberLen=4
AccumulateExtensionIn=0
MSN=
RangeLow=1000
RangeHigh=2999
PcCfg1=P=0x4a Y 0
PcCfg2=P=0x4f Y 0
PcCfg3=P=0x35 Y 0
PcCfg4=P=0x2c D 0
PcCfg5=P=0x30 B 0x00
PcCfg6=P=0x37 D 0
PcCfg7=P=0x39 D 0
PcCfgMtpx1=W="Cfg\Ctrl\ECT\Emulation" Y 0
Protocol=CORNET-N
GenerateRingtone=0
AutoSpid=0
SpidMode=3
ForceAlert=0
AddToConference=0
RemoveFromConference=0
MessageWaiting=0
CallTransfer=0
CallAppearances=0
ElectronicKeyTouchSystem=0
DisplayValAs=10
EnableLayer1Tristate=0
DeviceMode=0
PbxType=10
CallRefFormat=0
ChannelIdentifierFormat=0
ChannelAssignment=0
QSigStandard=4
InterfaceType=1
Point2Point=1
TEI=0
L2Mode=1
LeasedLineMode=0
CodeVariant=0
CRCMode=0
Role=0
RBSDID=1
RBSGlaResPa=1
RBSBearerCapability=4
RBSAnswerDelay=120
RBSrxDigitTimeOut=10
RBSStart=0
RbsAnswerSupervision=0
RbsSpecialAccess=0
RBSDial=1
BChnCnt=0
ForceLaw=0
FractionalLine=0
LowChannel=0
R2Dialect=0
R2CTryLength=-1
R2CliReq=1
BChnMask=0
NoHscx30=0
NumTEIs=1
Part68Limiter=0
ECTTransferType=0
DiscOnProgress=0
RoutingAccessAuthor=0
QSigPathReplaceInvite=0
QSigTranspFacility=0
QSigRerouting=1
MsgWaitingMode=0
CallDeflection=0
RdnEmulation=0
ECTLinkBalance=0
CallTransferMode=0
ReroutingOptimization=0
CollectTimeout=0

[LINE6]
LineType=0
LinePool=0
GUIReserved=0000000000000000000000000000000000000000
NumberType=2
NumberLen=4
AccumulateExtensionIn=0
MSN=
RangeLow=1000
RangeHigh=2999
PcCfg1=P=0x4a Y 0
PcCfg2=P=0x4f Y 0
PcCfg3=P=0x35 Y 0
PcCfg4=P=0x2c D 0
PcCfg5=P=0x30 B 0x00
PcCfg6=P=0x37 D 0
PcCfg7=P=0x39 D 0
PcCfgMtpx1=W="Cfg\Ctrl\ECT\Emulation" Y 0
Protocol=CORNET-N
GenerateRingtone=0
AutoSpid=0
SpidMode=3
ForceAlert=0
AddToConference=0
RemoveFromConference=0
MessageWaiting=0
CallTransfer=0
CallAppearances=0
ElectronicKeyTouchSystem=0
DisplayValAs=10
EnableLayer1Tristate=0
DeviceMode=0
PbxType=10
CallRefFormat=0
ChannelIdentifierFormat=0
ChannelAssignment=0
QSigStandard=4
InterfaceType=1
Point2Point=1
TEI=0
L2Mode=1
LeasedLineMode=0
CodeVariant=0
CRCMode=0
Role=0
RBSDID=1
RBSGlaResPa=1
RBSBearerCapability=4
RBSAnswerDelay=120
RBSrxDigitTimeOut=10
RBSStart=0
RbsAnswerSupervision=0
RbsSpecialAccess=0
RBSDial=1
BChnCnt=0
ForceLaw=0
FractionalLine=0
LowChannel=0
R2Dialect=0
R2CTryLength=-1
R2CliReq=1
BChnMask=0
NoHscx30=0
NumTEIs=1
Part68Limiter=0
ECTTransferType=0
DiscOnProgress=0
RoutingAccessAuthor=0
QSigPathReplaceInvite=0
QSigTranspFacility=0
QSigRerouting=1
MsgWaitingMode=0
CallDeflection=0
RdnEmulation=0
ECTLinkBalance=0
CallTransferMode=0
ReroutingOptimization=0
CollectTimeout=0

[LINE7]
LineType=0
LinePool=0
GUIReserved=0000000000000000000000000000000000000000
NumberType=2
NumberLen=4
AccumulateExtensionIn=0
MSN=
RangeLow=1000
RangeHigh=2999
PcCfg1=P=0x4a Y 0
PcCfg2=P=0x4f Y 0
PcCfg3=P=0x35 Y 0
PcCfg4=P=0x2c D 0
PcCfg5=P=0x30 B 0x00
PcCfg6=P=0x37 D 0
PcCfg7=P=0x39 D 0
PcCfgMtpx1=W="Cfg\Ctrl\ECT\Emulation" Y 0
Protocol=CORNET-N
GenerateRingtone=0
AutoSpid=0
SpidMode=3
ForceAlert=0
AddToConference=0
RemoveFromConference=0
MessageWaiting=0
CallTransfer=0
CallAppearances=0
ElectronicKeyTouchSystem=0
DisplayValAs=10
EnableLayer1Tristate=0
DeviceMode=0
PbxType=10
CallRefFormat=0
ChannelIdentifierFormat=0
ChannelAssignment=0
QSigStandard=4
InterfaceType=1
Point2Point=1
TEI=0
L2Mode=1
LeasedLineMode=0
CodeVariant=0
CRCMode=0
Role=0
RBSDID=1
RBSGlaResPa=1
RBSBearerCapability=4
RBSAnswerDelay=120
RBSrxDigitTimeOut=10
RBSStart=0
RbsAnswerSupervision=0
RbsSpecialAccess=0
RBSDial=1
BChnCnt=0
ForceLaw=0
FractionalLine=0
LowChannel=0
R2Dialect=0
R2CTryLength=-1
R2CliReq=1
BChnMask=0
NoHscx30=0
NumTEIs=1
Part68Limiter=0
ECTTransferType=0
DiscOnProgress=0
RoutingAccessAuthor=0
QSigPathReplaceInvite=0
QSigTranspFacility=0
QSigRerouting=1
MsgWaitingMode=0
CallDeflection=0
RdnEmulation=0
ECTLinkBalance=0
CallTransferMode=0
ReroutingOptimization=0
CollectTimeout=0

[LINE8]
LineType=0
LinePool=0
GUIReserved=0000000000000000000000000000000000000000
NumberType=2
NumberLen=4
AccumulateExtensionIn=0
MSN=
RangeLow=1000
RangeHigh=2999
PcCfg1=P=0x4a Y 0
PcCfg2=P=0x4f Y 0
PcCfg3=P=0x35 Y 0
PcCfg4=P=0x2c D 0
PcCfg5=P=0x30 B 0x00
PcCfg6=P=0x37 D 0
PcCfg7=P=0x39 D 0
PcCfgMtpx1=W="Cfg\Ctrl\ECT\Emulation" Y 0
Protocol=CORNET-N
GenerateRingtone=0
AutoSpid=0
SpidMode=3
ForceAlert=0
AddToConference=0
RemoveFromConference=0
MessageWaiting=0
CallTransfer=0
CallAppearances=0
ElectronicKeyTouchSystem=0
DisplayValAs=10
EnableLayer1Tristate=0
DeviceMode=0
PbxType=10
CallRefFormat=0
ChannelIdentifierFormat=0
ChannelAssignment=0
QSigStandard=4
InterfaceType=1
Point2Point=1
TEI=0
L2Mode=1
LeasedLineMode=0
CodeVariant=0
CRCMode=0
Role=0
RBSDID=1
RBSGlaResPa=1
RBSBearerCapability=4
RBSAnswerDelay=120
RBSrxDigitTimeOut=10
RBSStart=0
RbsAnswerSupervision=0
RbsSpecialAccess=0
RBSDial=1
BChnCnt=0
ForceLaw=0
FractionalLine=0
LowChannel=0
R2Dialect=0
R2CTryLength=-1
R2CliReq=1
BChnMask=0
NoHscx30=0
NumTEIs=1
Part68Limiter=0
ECTTransferType=0
DiscOnProgress=0
RoutingAccessAuthor=0
QSigPathReplaceInvite=0
QSigTranspFacility=0
QSigRerouting=1
MsgWaitingMode=0
CallDeflection=0
RdnEmulation=0
ECTLinkBalance=0
CallTransferMode=0
ReroutingOptimization=0
CollectTimeout=0

[BIND5]
ColpColrOn=0
ClipClirOnDefault=0
From=CARD1
To=LINE1
Service=0x00000000
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=1
Channels=0
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND6]
ColpColrOn=0
ClipClirOnDefault=0
From=CARD1
To=LINE2
Service=0x00000000
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=2
Channels=0
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND7]
ColpColrOn=0
ClipClirOnDefault=0
From=CARD1
To=LINE3
Service=0x00000000
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=3
Channels=0
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND8]
ColpColrOn=0
ClipClirOnDefault=0
From=CARD1
To=LINE4
Service=0x00000000
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=4
Channels=0
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND1]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL1
To=CARD1
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=1
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND2]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL1
To=CARD1
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=2
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND3]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL1
To=CARD1
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=3
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND4]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL1
To=CARD1
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=4
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND13]
ColpColrOn=0
ClipClirOnDefault=0
From=CARD2
To=LINE5
Service=0x00000000
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=1
Channels=0
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND14]
ColpColrOn=0
ClipClirOnDefault=0
From=CARD2
To=LINE6
Service=0x00000000
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=2
Channels=0
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND15]
ColpColrOn=0
ClipClirOnDefault=0
From=CARD2
To=LINE7
Service=0x00000000
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=3
Channels=0
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND16]
ColpColrOn=0
ClipClirOnDefault=0
From=CARD2
To=LINE8
Service=0x00000000
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=4
Channels=0
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND9]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL1
To=CARD2
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=1
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND10]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL1
To=CARD2
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=2
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND11]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL1
To=CARD2
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=3
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND12]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL1
To=CARD2
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=0
ToLine=4
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND17]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL2
To=CARD1
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=1
ToLine=1
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND18]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL2
To=CARD1
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=2
ToLine=2
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND19]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL2
To=CARD1
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=3
ToLine=3
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND20]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL2
To=CARD1
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=4
ToLine=4
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND21]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL2
To=CARD2
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=5
ToLine=1
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND22]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL2
To=CARD2
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=6
ToLine=2
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND23]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL2
To=CARD2
Service=0xffffffff
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=7
ToLine=3
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[BIND24]
ColpColrOn=0
ClipClirOnDefault=0
From=APPL2
To=CARD2
Service=0xffff0000
CallPolicyIncoming=2
MSN_Presentation=0
SwitchFeature ECT=0
SwitchFeature Overlapped Sending=0
SwitchFeature 3PTY=0
SwitchFeature nPTY=0
SwitchFeature LIPTY=0
Use one msn per line=0
Controller=8
ToLine=4
Channels=2
NumberType=0xffffffff
MSN=
AutomaticLayer1Down=0

[GENERAL]
APPLICATIONS=APPL1,APPL2
CARDS=CARD1,CARD2
LINES=LINE1,LINE2,LINE3,LINE4,LINE5,LINE6,LINE7,LINE8
RELATIONS=BIND5,BIND6,BIND7,BIND8,BIND1,BIND2,BIND3,BIND4,BIND13,BIND14,BIND15,BIND16,BIND9,BIND10,BIND11,BIND12,BIND17,BIND18,BIND19,BIND20,BIND21,BIND22,BIND23,BIND24

**** Local config - END ****

16:07:58.484 R 0 DIMAINT: Maintenance_Tools maint/4/nt 106-522
16:07:59.187 R 1 MTPX: 106-274 (Jun 12 2006/23:54:05)
16:08:01.296 R 2 DiwanSrv: 106-853 (Jun 29 2006/17:26:03)
16:08:05.312 R 3 Adapter 0008-1: Diva Server 4BRI-8M 2.0 PCI #11841
16:08:07.000 R 4 Adapter 0008-2: Diva Server 4BRI-8M 2.0 PCI #11841
16:08:07.781 R 5 Adapter 0008-3: Diva Server 4BRI-8M 2.0 PCI #11841
16:08:08.578 R 6 Adapter 0008-4: Diva Server 4BRI-8M 2.0 PCI #11841
16:08:13.421 R 7 Adapter 0009-1: Diva Server 4BRI-8M 2.0 PCI #11845
16:08:15.109 R 8 Adapter 0009-2: Diva Server 4BRI-8M 2.0 PCI #11845
16:08:15.828 R 9 Adapter 0009-3: Diva Server 4BRI-8M 2.0 PCI #11845
16:08:16.687 R 10 Adapter 0009-4: Diva Server 4BRI-8M 2.0 PCI #11845
--
16:08:45.843 R 11 CAPI20: CAPI 2.0 Driver capi/nt.v16/1.srv 106-13
--
8:32:42.031 L 3 *** Management dump - BEGIN Diva Server 4BRI-8M 2.0 PCI #11841-1 ***
8:32:42.046 L 3 r-- UInt 2 Info\CardType = 53
8:32:42.046 L 3 r-- UInt 4 Info\SerialNumber = 11841
8:32:42.046 L 3 r-- Number 1 Info\HW_InfoStruct = 00
8:32:42.046 L 3 r-- UInt 1 Info\InterfaceNr = 0
8:32:42.046 L 3 r-- UInt 2 Info\BoardRevision = 0
8:32:42.046 L 3 r-- UInt 2 Info\SubFunction = 0
8:32:42.046 L 3 r-- UInt 2 Info\SubDevice = 20
8:32:42.046 L 3 r-- AsciiZ 58 Info\ProtocolBuild = "TE_DMLT, Build 106-112, Protocol 6.03(V16) 105-2 [F#00FF]"
8:32:42.046 L 3 r-- AsciiZ 53 Info\DSPCodeBuild = "DIVA Server BRI 2M Kernel Version 1.00 Build 106-642"
8:32:42.046 L 3 r-- Bool 1 Info\PRI = FALSE
8:32:42.046 L 3 r-- UInt 1 Info\Channels = 2
8:32:42.046 L 3 r-- UInt 1 Info\AnalogChannels = 2
8:32:42.046 L 3 r-- Bool 4 Info\PCIDMA = TRUE
8:32:42.046 L 3 r-- Exec 0 Info\IdentifyStart
8:32:42.046 L 3 r-- BitFld 4 Info\DSPState = 0000:0000:0000:0000:0000:0000:0000:0011
8:32:42.046 L 3 r-- Dir 1 Config\US-EKTS
8:32:42.046 L 3 rw- UInt 1 Config\US-EKTS\CACH Appearances = 0
8:32:42.046 L 3 rw- Bool 1 Config\US-EKTS\Force-Alert = FALSE
8:32:42.046 L 3 rw- HInt 1 Config\US-EKTS\Key BeginConf = 0x00
8:32:42.046 L 3 rw- HInt 1 Config\US-EKTS\Key DropConf = 0x00
8:32:42.046 L 3 rw- HInt 1 Config\US-EKTS\Key VoiceMail = 0x01
8:32:42.046 L 3 rw- HInt 1 Config\US-EKTS\Key CallTransfer = 0x00
8:32:42.046 L 3 rw- Bool 1 Config\US-EKTS\Disable AutoSPID = FALSE
8:32:42.046 L 3 r-- Dir 1 Config\DChannel
8:32:42.062 L 3 r-- AsciiZ 9 Config\DChannel\Name = "NONE(20)"
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\E-DSS1 (EURO)
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\FRANCE (VN3)
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\FRANCE (VN6)
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\BELGIUM
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\DMS (Nortel)
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\5ESS Custom
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\JAPAN
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\ITALY
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\TAIWAN
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\AUSTRALIA
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\NEWZEALAND
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\HONGKONG
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\5ESS NI Lucent
8:32:42.062 L 3 r-- Exec 0 Config\DChannel\QSIG
8:32:42.062 L 3 rw- UInt 1 Config\DChannel\Protocol = 20
8:32:42.062 L 3 r-- AsciiZ 22 Config\DChannel\Release = "17:10:34, Jun 29 2006"
8:32:42.062 L 3 r-- Dir 1 Config\Layer3
8:32:42.062 L 3 rw- UInt 1 Config\Layer3\RejectCauseNoListen = 0
8:32:42.062 L 3 rw- UInt 1 Config\Layer3\RejectCauseIgnore = 0
8:32:42.062 L 3 rw- UInt 1 Config\Layer3\DiscAfterProgress = 0
8:32:42.062 L 3 rw- Number 1 Config\Layer3\CHI Interfaceident = 00
8:32:42.062 L 3 rw- UInt 1 Config\Layer3\CLIOrder = 0
8:32:42.062 L 3 rw- UInt 1 Config\Layer3\SdncmplMin = 4
8:32:42.062 L 3 rw- UInt 1 Config\Layer3\ProgressToneProt = 1
8:32:42.062 L 3 r-- Dir 1 Config\Layer2
8:32:42.062 L 3 r-- AsciiZ 17 Config\Layer2\Stable L2 = "Send No Disc (1)"
8:32:42.062 L 3 r-- Exec 0 Config\Layer2\On demand (0)
8:32:42.062 L 3 r-- Exec 0 Config\Layer2\Send No Disc (1)
8:32:42.062 L 3 r-- Exec 0 Config\Layer2\Permanent (2)
8:32:42.062 L 3 rw- UInt 1 Config\Layer2\L2 = 1
8:32:42.062 L 3 r-- Dir 1 Config\Layer1
8:32:42.078 L 3 r-- HInt 1 Config\Layer1\L1HuntGroupConf = 0x00
8:32:42.078 L 3 rw- UInt 1 Config\Layer1\Part68 Level Lim = 1
8:32:42.078 L 3 rw- Bool 1 Config\Layer1\Recording AGC = FALSE
8:32:42.078 L 3 rw- BitFld 1 Config\Layer1\Dial Pulse Det. = 0000:0000
8:32:42.078 L 3 rw- Bool 1 Config\Layer1\DTMF Suppressor = FALSE
8:32:42.078 L 3 rw- Bool 1 Config\Layer1\LI Via Host Mem. = FALSE
8:32:42.078 L 3 rw- Bool 1 Config\Layer1\Conf. AGC Enable = TRUE
8:32:42.078 L 3 rw- UInt 2 Config\Layer1\Conf. AGC MinPart = 4
8:32:42.078 L 3 rw- HInt 2 Config\Layer1\Conf. AGC Thresh = 0x0100
8:32:42.078 L 3 r-- Dir 1 Config\B-Layer1
8:32:42.078 L 3 rw- BitFld 4 Config\B-Layer1\Disabled DSPs = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.078 L 3 r-- Dir 1 Config\Modem
8:32:42.078 L 3 rw- BitFld 1 Config\Modem\Protocol Neg. = 0000:0000
8:32:42.078 L 3 rw- BitFld 1 Config\Modem\Protocol Opt. = 0000:0000
8:32:42.078 L 3 rw- UInt 1 Config\Modem\Break Config. = 0
8:32:42.078 L 3 rw- UInt 2 Config\Modem\Validation Chars = 0
8:32:42.078 L 3 rw- BitFld 1 Config\Modem\Line Taking Opt. = 0000:0000
8:32:42.078 L 3 rw- UInt 1 Config\Modem\Negotiation Mode = 0
8:32:42.078 L 3 rw- UInt 1 Config\Modem\Guard Tone = 0
8:32:42.078 L 3 rw- BitFld 1 Config\Modem\Modulation Opt. = 0000:0000
8:32:42.078 L 3 rw- BitFld 2 Config\Modem\Disabled Mod. = 0000:0000:0000:0000
8:32:42.078 L 3 rw- BitFld 1 Config\Modem\Enabled Mod. = 0000:0000
8:32:42.078 L 3 rw- UInt 2 Config\Modem\TX Min Speed = 0
8:32:42.078 L 3 rw- UInt 2 Config\Modem\TX Max Speed = 0
8:32:42.078 L 3 rw- UInt 2 Config\Modem\RX Min Speed = 0
8:32:42.078 L 3 rw- UInt 2 Config\Modem\RX Max Speed = 0
8:32:42.078 L 3 rw- BitFld 1 Config\Modem\Disabled Symb. = 0000:0000
8:32:42.078 L 3 rw- BitFld 1 Config\Modem\INFO Options = 0000:0000
8:32:42.078 L 3 rw- UInt 1 Config\Modem\TX Level Adj. = 0
8:32:42.078 L 3 rw- UInt 1 Config\Modem\Speaker Control = 0
8:32:42.078 L 3 rw- UInt 1 Config\Modem\Speaker Volume = 0
8:32:42.078 L 3 rw- UInt 1 Config\Modem\Carrier Wait sec. = 0
8:32:42.078 L 3 rw- UInt 1 Config\Modem\Carrier Loss 10th = 0
8:32:42.078 L 3 rw- UInt 1 Config\Modem\DCD ON Threshold = 0
8:32:42.078 L 3 rw- HInt 2 Config\Modem\Eye Setup = 0x0000
8:32:42.078 L 3 r-- Dir 1 Config\Modem\Proprietary
8:32:42.093 L 3 rw- BitFld 2 Config\Modem\Proprietary\Options = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 4 Config\Modem\Proprietary\Enabled Mod. = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.093 L 3 rw- UInt 2 Config\Modem\Proprietary\Echo Suppress ms = 0
8:32:42.093 L 3 rw- UInt 2 Config\Modem\Proprietary\Preamble Time ms = 0
8:32:42.093 L 3 rw- UInt 2 Config\Modem\Proprietary\Clean Carrier ms = 0
8:32:42.093 L 3 rw- UInt 2 Config\Modem\Proprietary\Validation Chars = 0
8:32:42.093 L 3 rw- BitFld 2 Config\Modem\Proprietary\Async Format 1 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\Modem\Proprietary\Async Format 2 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\Modem\Proprietary\Async Format 3 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\Modem\Proprietary\Async Format 4 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\Modem\Proprietary\Async Format 5 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\Modem\Proprietary\Async Format 6 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\Modem\Proprietary\Async Format 7 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\Modem\Proprietary\Async Format 8 = 0000:0000:0000:0000
8:32:42.093 L 3 r-- Dir 1 Config\FAX
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Options = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Options2 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- UInt 2 Config\FAX\Min Speed = 0
8:32:42.093 L 3 rw- UInt 2 Config\FAX\Max Speed = 0
8:32:42.093 L 3 rw- BitFld 1 Config\FAX\Disabled Res. = 0000:0000
8:32:42.093 L 3 rw- UInt 1 Config\FAX\Record. Width = 0
8:32:42.093 L 3 rw- UInt 1 Config\FAX\Record. Length = 0
8:32:42.093 L 3 rw- UInt 1 Config\FAX\Scanline Time = 0
8:32:42.093 L 3 rw- UInt 1 Config\FAX\TX Level Adj. = 0
8:32:42.093 L 3 rw- UInt 2 Config\FAX\Max Overhead sec. = 0
8:32:42.093 L 3 rw- BitFld 1 Config\FAX\Disabled Symb. = 0000:0000
8:32:42.093 L 3 rw- BitFld 1 Config\FAX\INFO Options = 0000:0000
8:32:42.093 L 3 r-- Dir 1 Config\FAX\Font
8:32:42.093 L 3 rw- HInt 1 Config\FAX\Font\Code = 0x00
8:32:42.093 L 3 r-- Exec 0 Config\FAX\Font\Read
8:32:42.093 L 3 r-- Exec 0 Config\FAX\Font\Write
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row1 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row2 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row3 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row4 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row5 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row6 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row7 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row8 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row9 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row10 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row11 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row12 = 0000:0000:0000:0000
8:32:42.093 L 3 rw- BitFld 2 Config\FAX\Font\Row13 = 0000:0000:0000:0000
8:32:42.109 L 3 rw- BitFld 2 Config\FAX\Font\Row14 = 0000:0000:0000:0000
8:32:42.109 L 3 rw- BitFld 2 Config\FAX\Font\Row15 = 0000:0000:0000:0000
8:32:42.109 L 3 rw- BitFld 2 Config\FAX\Font\Row16 = 0000:0000:0000:0000
8:32:42.109 L 3 r-- Dir 1 Config\V.110
8:32:42.109 L 3 rw- BitFld 2 Config\V.110\Options = 0000:0000:0000:0000
8:32:42.109 L 3 rw- UInt 2 Config\V.110\Pure Sync Time = 80
8:32:42.109 L 3 rw- UInt 2 Config\V.110\Data Start Delay = 20
8:32:42.109 L 3 r-- Dir 1 Config\V.120
8:32:42.109 L 3 rw- BitFld 4 Config\V.120\Options = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.109 L 3 r-- Dir 1 Config\X.75
8:32:42.109 L 3 rw- BitFld 4 Config\X.75\Options = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.109 L 3 r-- Dir 1 Config\X.25
8:32:42.125 L 3 rw- BitFld 4 Config\X.25\Options = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.125 L 3 r-- Dir 1 Config\Qsig
8:32:42.125 L 3 rw- UInt 1 Config\Qsig\CR Length = 0
8:32:42.125 L 3 rw- UInt 1 Config\Qsig\CHI Length = 0
8:32:42.125 L 3 rw- Bool 1 Config\Qsig\Charge Rate = TRUE
8:32:42.125 L 3 rw- Bool 1 Config\Qsig\Charge Interim = TRUE
8:32:42.125 L 3 rw- Bool 1 Config\Qsig\Charge Final = TRUE
8:32:42.125 L 3 rw- Bool 1 Config\Qsig\Charge in Setup = FALSE
8:32:42.125 L 3 rw- Bool 1 Config\Qsig\Transp Facility = FALSE
8:32:42.125 L 3 rw- Bool 1 Config\Qsig\No Rerouting = FALSE
8:32:42.125 L 3 rw- Bool 1 Config\Qsig\PrInvite = FALSE
8:32:42.125 L 3 rw- Bool 1 Config\Qsig\EricssonMWI = FALSE
8:32:42.125 L 3 rw- UInt 1 Config\Qsig\QSIGDialect = 3
8:32:42.125 L 3 r-- Dir 1 Config\Supplementary Values
8:32:42.125 L 3 rw- UInt 1 Config\Supplementary Values\TSC-CR-Value = 0
8:32:42.125 L 3 rw- Bool 1 Config\Supplementary Values\TSC-CR-Enable = FALSE
8:32:42.125 L 3 rw- Bool 1 Config\Supplementary Values\use first RDN = TRUE
8:32:42.125 L 3 rw- Bool 1 Config\Supplementary Values\ETSI MWI REG = TRUE
8:32:42.125 L 3 rw- UInt 2 Config\Supplementary Values\CCBS Rel Timer = 15
8:32:42.125 L 3 rw- Bool 1 Config\Supplementary Values\ETSI ECT auto = FALSE
8:32:42.125 L 3 rw- Bool 1 Config\Supplementary Values\ETSI ECT forceimpl = TRUE
8:32:42.125 L 3 rw- Bool 1 Config\Supplementary Values\ETSI ECT forceexpl = FALSE
8:32:42.125 L 3 rw- UInt 1 Config\Supplementary Values\ETSI ECT LinkIdfailcount = 0
8:32:42.125 L 3 rw- Bool 1 Config\Supplementary Values\ETSI SWISS Name = FALSE
8:32:42.125 L 3 rw- HInt 4 Config\Supplementary Values\SSFeatures = 0x00000000
8:32:42.125 L 3 rw- UInt 1 Config\Version = 0
8:32:42.125 L 3 rw- UInt 1 Config\DID-Length = 4
8:32:42.125 L 3 rw- Bool 1 Config\Ringertone = FALSE
8:32:42.125 L 3 rw- UInt 2 Config\Alert-Timeout = 0
8:32:42.125 L 3 rw- UInt 2 Config\Redial-Timeout = 0
8:32:42.125 L 3 rw- UInt 1 Config\Redial-Attempts = 0
8:32:42.125 L 3 rw- Bool 1 Config\NT = FALSE
8:32:42.125 L 3 r-- Bool 1 Config\PRI = FALSE
8:32:42.125 L 3 rw- Bool 1 Config\GlobalCRs = TRUE
8:32:42.125 L 3 rw- Bool 1 Config\NoOrderCheck = FALSE
8:32:42.125 L 3 rw- Bool 1 Config\NT-2 = TRUE
8:32:42.125 L 3 r-- BitFld 4 Config\UnChBMask = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.125 L 3 r-- UInt 2 Config\CardType = 53
8:32:42.125 L 3 r-- UInt 4 Config\SerialNumber = 11841
8:32:42.125 L 3 r-- HInt 2 Config\BoardRevision = 0x0000
8:32:42.125 L 3 r-- UInt 2 Config\SubFunction = 0
8:32:42.125 L 3 r-- BitFld 4 Config\DSPState = 0000:0000:0000:0000:0000:0000:0000:0011
8:32:42.125 L 3 r-- Dir 13 Config\SPID-1
8:32:42.140 L 3 rw- Bool 1 Config\SPID-1\Automatic TEI = FALSE
8:32:42.140 L 3 r-- UInt 1 Config\SPID-1\TEI = 0
8:32:42.140 L 3 rw- Ascii 1 Config\SPID-1\SPID = ""
8:32:42.140 L 3 rw- Ascii 1 Config\SPID-1\Number = ""
8:32:42.140 L 3 rw- Ascii 1 Config\SPID-1\Sub-Adr = ""
8:32:42.140 L 3 r-- UInt 2 Config\SPID-1\Global-MWI = 0
8:32:42.140 L 3 r-- Dir 13 Config\SPID-2
8:32:42.140 L 3 rw- Bool 1 Config\SPID-2\Automatic TEI = TRUE
8:32:42.140 L 3 r-- UInt 1 Config\SPID-2\TEI = 0
8:32:42.140 L 3 rw- Ascii 1 Config\SPID-2\SPID = ""
8:32:42.140 L 3 rw- Ascii 1 Config\SPID-2\Number = ""
8:32:42.140 L 3 rw- Ascii 1 Config\SPID-2\Sub-Adr = ""
8:32:42.140 L 3 r-- UInt 2 Config\SPID-2\Global-MWI = 0
8:32:42.140 L 3 r-- Dir 13 Config\SPID-3
8:32:42.140 L 3 rw- Bool 1 Config\SPID-3\Automatic TEI = TRUE
8:32:42.140 L 3 r-- UInt 1 Config\SPID-3\TEI = 0
8:32:42.140 L 3 rw- Ascii 1 Config\SPID-3\SPID = ""
8:32:42.140 L 3 rw- Ascii 1 Config\SPID-3\Number = ""
8:32:42.140 L 3 rw- Ascii 1 Config\SPID-3\Sub-Adr = ""
8:32:42.140 L 3 r-- UInt 2 Config\SPID-3\Global-MWI = 0
8:32:42.140 L 3 r-- Dir 13 Config\SPID-4
8:32:42.140 L 3 rw- Bool 1 Config\SPID-4\Automatic TEI = TRUE
8:32:42.140 L 3 r-- UInt 1 Config\SPID-4\TEI = 0
8:32:42.140 L 3 rw- Ascii 1 Config\SPID-4\SPID = ""
8:32:42.140 L 3 rw- Ascii 1 Config\SPID-4\Number = ""
8:32:42.140 L 3 rw- Ascii 1 Config\SPID-4\Sub-Adr = ""
8:32:42.140 L 3 r-- UInt 2 Config\SPID-4\Global-MWI = 0
8:32:42.140 L 3 r-- Dir 13 Config\SPID-5
8:32:42.156 L 3 rw- Bool 1 Config\SPID-5\Automatic TEI = TRUE
8:32:42.156 L 3 r-- UInt 1 Config\SPID-5\TEI = 0
8:32:42.156 L 3 rw- Ascii 1 Config\SPID-5\SPID = ""
8:32:42.156 L 3 rw- Ascii 1 Config\SPID-5\Number = ""
8:32:42.156 L 3 rw- Ascii 1 Config\SPID-5\Sub-Adr = ""
8:32:42.156 L 3 r-- UInt 2 Config\SPID-5\Global-MWI = 0
8:32:42.156 L 3 r-- Dir 13 Config\SPID-6
8:32:42.156 L 3 rw- Bool 1 Config\SPID-6\Automatic TEI = TRUE
8:32:42.156 L 3 r-- UInt 1 Config\SPID-6\TEI = 0
8:32:42.156 L 3 rw- Ascii 1 Config\SPID-6\SPID = ""
8:32:42.156 L 3 rw- Ascii 1 Config\SPID-6\Number = ""
8:32:42.156 L 3 rw- Ascii 1 Config\SPID-6\Sub-Adr = ""
8:32:42.156 L 3 r-- UInt 2 Config\SPID-6\Global-MWI = 0
8:32:42.156 L 3 r-- Dir 13 Config\SPID-7
8:32:42.156 L 3 rw- Bool 1 Config\SPID-7\Automatic TEI = TRUE
8:32:42.156 L 3 r-- UInt 1 Config\SPID-7\TEI = 0
8:32:42.156 L 3 rw- Ascii 1 Config\SPID-7\SPID = ""
8:32:42.156 L 3 rw- Ascii 1 Config\SPID-7\Number = ""
8:32:42.156 L 3 rw- Ascii 1 Config\SPID-7\Sub-Adr = ""
8:32:42.156 L 3 r-- UInt 2 Config\SPID-7\Global-MWI = 0
8:32:42.156 L 3 r-- Dir 13 Config\SPID-8
8:32:42.171 L 3 rw- Bool 1 Config\SPID-8\Automatic TEI = TRUE
8:32:42.171 L 3 r-- UInt 1 Config\SPID-8\TEI = 0
8:32:42.171 L 3 rw- Ascii 1 Config\SPID-8\SPID = ""
8:32:42.171 L 3 rw- Ascii 1 Config\SPID-8\Number = ""
8:32:42.171 L 3 rw- Ascii 1 Config\SPID-8\Sub-Adr = ""
8:32:42.171 L 3 r-- UInt 2 Config\SPID-8\Global-MWI = 0
8:32:42.171 L 3 rw- UInt 1 Config\L2LinkCount = 1
8:32:42.171 L 3 rw- UInt 1 Config\CPN-Length = 21
8:32:42.171 L 3 r-- UInt 1 Config\BChannelCount = 2
8:32:42.171 L 3 *** Management dump - END ***
8:32:42.171 L 4 *** Management dump - BEGIN Diva Server 4BRI-8M 2.0 PCI #11841-2 ***
8:32:42.171 L 4 r-- UInt 2 Info\CardType = 53
8:32:42.171 L 4 r-- UInt 4 Info\SerialNumber = 11841
8:32:42.171 L 4 r-- Number 1 Info\HW_InfoStruct = 00
8:32:42.171 L 4 r-- UInt 1 Info\InterfaceNr = 1
8:32:42.171 L 4 r-- UInt 2 Info\BoardRevision = 0
8:32:42.171 L 4 r-- UInt 2 Info\SubFunction = 0
8:32:42.171 L 4 r-- UInt 2 Info\SubDevice = 20
8:32:42.171 L 4 r-- AsciiZ 58 Info\ProtocolBuild = "TE_DMLT, Build 106-112, Protocol 6.03(V16) 105-2 [F#00FF]"
8:32:42.171 L 4 r-- AsciiZ 53 Info\DSPCodeBuild = "DIVA Server BRI 2M Kernel Version 1.00 Build 106-642"
8:32:42.171 L 4 r-- Bool 1 Info\PRI = FALSE
8:32:42.171 L 4 r-- UInt 1 Info\Channels = 2
8:32:42.171 L 4 r-- UInt 1 Info\AnalogChannels = 2
8:32:42.171 L 4 r-- Bool 4 Info\PCIDMA = TRUE
8:32:42.171 L 4 r-- Exec 0 Info\IdentifyStart
8:32:42.171 L 4 r-- BitFld 4 Info\DSPState = 0000:0000:0000:0000:0000:0000:0000:0011
8:32:42.171 L 4 r-- Dir 1 Config\US-EKTS
8:32:42.187 L 4 rw- UInt 1 Config\US-EKTS\CACH Appearances = 0
8:32:42.187 L 4 rw- Bool 1 Config\US-EKTS\Force-Alert = FALSE
8:32:42.187 L 4 rw- HInt 1 Config\US-EKTS\Key BeginConf = 0x00
8:32:42.187 L 4 rw- HInt 1 Config\US-EKTS\Key DropConf = 0x00
8:32:42.187 L 4 rw- HInt 1 Config\US-EKTS\Key VoiceMail = 0x01
8:32:42.187 L 4 rw- HInt 1 Config\US-EKTS\Key CallTransfer = 0x00
8:32:42.187 L 4 rw- Bool 1 Config\US-EKTS\Disable AutoSPID = FALSE
8:32:42.187 L 4 r-- Dir 1 Config\DChannel
8:32:42.187 L 4 r-- AsciiZ 9 Config\DChannel\Name = "NONE(20)"
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\E-DSS1 (EURO)
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\FRANCE (VN3)
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\FRANCE (VN6)
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\BELGIUM
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\DMS (Nortel)
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\5ESS Custom
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\JAPAN
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\ITALY
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\TAIWAN
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\AUSTRALIA
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\NEWZEALAND
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\HONGKONG
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\5ESS NI Lucent
8:32:42.187 L 4 r-- Exec 0 Config\DChannel\QSIG
8:32:42.187 L 4 rw- UInt 1 Config\DChannel\Protocol = 20
8:32:42.187 L 4 r-- AsciiZ 22 Config\DChannel\Release = "17:10:34, Jun 29 2006"
8:32:42.187 L 4 r-- Dir 1 Config\Layer3
8:32:42.187 L 4 rw- UInt 1 Config\Layer3\RejectCauseNoListen = 0
8:32:42.187 L 4 rw- UInt 1 Config\Layer3\RejectCauseIgnore = 0
8:32:42.187 L 4 rw- UInt 1 Config\Layer3\DiscAfterProgress = 0
8:32:42.187 L 4 rw- Number 1 Config\Layer3\CHI Interfaceident = 00
8:32:42.187 L 4 rw- UInt 1 Config\Layer3\CLIOrder = 0
8:32:42.187 L 4 rw- UInt 1 Config\Layer3\SdncmplMin = 4
8:32:42.187 L 4 rw- UInt 1 Config\Layer3\ProgressToneProt = 1
8:32:42.187 L 4 r-- Dir 1 Config\Layer2
8:32:42.187 L 4 r-- AsciiZ 17 Config\Layer2\Stable L2 = "Send No Disc (1)"
8:32:42.187 L 4 r-- Exec 0 Config\Layer2\On demand (0)
8:32:42.187 L 4 r-- Exec 0 Config\Layer2\Send No Disc (1)
8:32:42.187 L 4 r-- Exec 0 Config\Layer2\Permanent (2)
8:32:42.187 L 4 rw- UInt 1 Config\Layer2\L2 = 1
8:32:42.187 L 4 r-- Dir 1 Config\Layer1
8:32:42.203 L 4 r-- HInt 1 Config\Layer1\L1HuntGroupConf = 0x00
8:32:42.203 L 4 rw- UInt 1 Config\Layer1\Part68 Level Lim = 1
8:32:42.203 L 4 rw- Bool 1 Config\Layer1\Recording AGC = FALSE
8:32:42.203 L 4 rw- BitFld 1 Config\Layer1\Dial Pulse Det. = 0000:0000
8:32:42.203 L 4 rw- Bool 1 Config\Layer1\DTMF Suppressor = FALSE
8:32:42.203 L 4 rw- Bool 1 Config\Layer1\LI Via Host Mem. = FALSE
8:32:42.203 L 4 rw- Bool 1 Config\Layer1\Conf. AGC Enable = TRUE
8:32:42.203 L 4 rw- UInt 2 Config\Layer1\Conf. AGC MinPart = 4
8:32:42.203 L 4 rw- HInt 2 Config\Layer1\Conf. AGC Thresh = 0x0100
8:32:42.203 L 4 r-- Dir 1 Config\B-Layer1
8:32:42.203 L 4 rw- BitFld 4 Config\B-Layer1\Disabled DSPs = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.203 L 4 r-- Dir 1 Config\Modem
8:32:42.203 L 4 rw- BitFld 1 Config\Modem\Protocol Neg. = 0000:0000
8:32:42.203 L 4 rw- BitFld 1 Config\Modem\Protocol Opt. = 0000:0000
8:32:42.203 L 4 rw- UInt 1 Config\Modem\Break Config. = 0
8:32:42.203 L 4 rw- UInt 2 Config\Modem\Validation Chars = 0
8:32:42.203 L 4 rw- BitFld 1 Config\Modem\Line Taking Opt. = 0000:0000
8:32:42.203 L 4 rw- UInt 1 Config\Modem\Negotiation Mode = 0
8:32:42.203 L 4 rw- UInt 1 Config\Modem\Guard Tone = 0
8:32:42.203 L 4 rw- BitFld 1 Config\Modem\Modulation Opt. = 0000:0000
8:32:42.203 L 4 rw- BitFld 2 Config\Modem\Disabled Mod. = 0000:0000:0000:0000
8:32:42.203 L 4 rw- BitFld 1 Config\Modem\Enabled Mod. = 0000:0000
8:32:42.203 L 4 rw- UInt 2 Config\Modem\TX Min Speed = 0
8:32:42.203 L 4 rw- UInt 2 Config\Modem\TX Max Speed = 0
8:32:42.203 L 4 rw- UInt 2 Config\Modem\RX Min Speed = 0
8:32:42.203 L 4 rw- UInt 2 Config\Modem\RX Max Speed = 0
8:32:42.203 L 4 rw- BitFld 1 Config\Modem\Disabled Symb. = 0000:0000
8:32:42.203 L 4 rw- BitFld 1 Config\Modem\INFO Options = 0000:0000
8:32:42.203 L 4 rw- UInt 1 Config\Modem\TX Level Adj. = 0
8:32:42.203 L 4 rw- UInt 1 Config\Modem\Speaker Control = 0
8:32:42.203 L 4 rw- UInt 1 Config\Modem\Speaker Volume = 0
8:32:42.203 L 4 rw- UInt 1 Config\Modem\Carrier Wait sec. = 0
8:32:42.203 L 4 rw- UInt 1 Config\Modem\Carrier Loss 10th = 0
8:32:42.203 L 4 rw- UInt 1 Config\Modem\DCD ON Threshold = 0
8:32:42.203 L 4 rw- HInt 2 Config\Modem\Eye Setup = 0x0000
8:32:42.203 L 4 r-- Dir 1 Config\Modem\Proprietary
8:32:42.203 L 4 rw- BitFld 2 Config\Modem\Proprietary\Options = 0000:0000:0000:0000
8:32:42.203 L 4 rw- BitFld 4 Config\Modem\Proprietary\Enabled Mod. = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.203 L 4 rw- UInt 2 Config\Modem\Proprietary\Echo Suppress ms = 0
8:32:42.203 L 4 rw- UInt 2 Config\Modem\Proprietary\Preamble Time ms = 0
8:32:42.203 L 4 rw- UInt 2 Config\Modem\Proprietary\Clean Carrier ms = 0
8:32:42.203 L 4 rw- UInt 2 Config\Modem\Proprietary\Validation Chars = 0
8:32:42.203 L 4 rw- BitFld 2 Config\Modem\Proprietary\Async Format 1 = 0000:0000:0000:0000
8:32:42.203 L 4 rw- BitFld 2 Config\Modem\Proprietary\Async Format 2 = 0000:0000:0000:0000
8:32:42.203 L 4 rw- BitFld 2 Config\Modem\Proprietary\Async Format 3 = 0000:0000:0000:0000
8:32:42.203 L 4 rw- BitFld 2 Config\Modem\Proprietary\Async Format 4 = 0000:0000:0000:0000
8:32:42.203 L 4 rw- BitFld 2 Config\Modem\Proprietary\Async Format 5 = 0000:0000:0000:0000
8:32:42.203 L 4 rw- BitFld 2 Config\Modem\Proprietary\Async Format 6 = 0000:0000:0000:0000
8:32:42.203 L 4 rw- BitFld 2 Config\Modem\Proprietary\Async Format 7 = 0000:0000:0000:0000
8:32:42.203 L 4 rw- BitFld 2 Config\Modem\Proprietary\Async Format 8 = 0000:0000:0000:0000
8:32:42.203 L 4 r-- Dir 1 Config\FAX
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Options = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Options2 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- UInt 2 Config\FAX\Min Speed = 0
8:32:42.218 L 4 rw- UInt 2 Config\FAX\Max Speed = 0
8:32:42.218 L 4 rw- BitFld 1 Config\FAX\Disabled Res. = 0000:0000
8:32:42.218 L 4 rw- UInt 1 Config\FAX\Record. Width = 0
8:32:42.218 L 4 rw- UInt 1 Config\FAX\Record. Length = 0
8:32:42.218 L 4 rw- UInt 1 Config\FAX\Scanline Time = 0
8:32:42.218 L 4 rw- UInt 1 Config\FAX\TX Level Adj. = 0
8:32:42.218 L 4 rw- UInt 2 Config\FAX\Max Overhead sec. = 0
8:32:42.218 L 4 rw- BitFld 1 Config\FAX\Disabled Symb. = 0000:0000
8:32:42.218 L 4 rw- BitFld 1 Config\FAX\INFO Options = 0000:0000
8:32:42.218 L 4 r-- Dir 1 Config\FAX\Font
8:32:42.218 L 4 rw- HInt 1 Config\FAX\Font\Code = 0x00
8:32:42.218 L 4 r-- Exec 0 Config\FAX\Font\Read
8:32:42.218 L 4 r-- Exec 0 Config\FAX\Font\Write
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row1 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row2 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row3 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row4 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row5 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row6 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row7 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row8 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row9 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row10 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row11 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row12 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row13 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row14 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row15 = 0000:0000:0000:0000
8:32:42.218 L 4 rw- BitFld 2 Config\FAX\Font\Row16 = 0000:0000:0000:0000
8:32:42.218 L 4 r-- Dir 1 Config\V.110
8:32:42.218 L 4 rw- BitFld 2 Config\V.110\Options = 0000:0000:0000:0000
8:32:42.218 L 4 rw- UInt 2 Config\V.110\Pure Sync Time = 80
8:32:42.218 L 4 rw- UInt 2 Config\V.110\Data Start Delay = 20
8:32:42.218 L 4 r-- Dir 1 Config\V.120
8:32:42.218 L 4 rw- BitFld 4 Config\V.120\Options = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.218 L 4 r-- Dir 1 Config\X.75
8:32:42.234 L 4 rw- BitFld 4 Config\X.75\Options = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.234 L 4 r-- Dir 1 Config\X.25
8:32:42.234 L 4 rw- BitFld 4 Config\X.25\Options = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.234 L 4 r-- Dir 1 Config\Qsig
8:32:42.234 L 4 rw- UInt 1 Config\Qsig\CR Length = 0
8:32:42.234 L 4 rw- UInt 1 Config\Qsig\CHI Length = 0
8:32:42.234 L 4 rw- Bool 1 Config\Qsig\Charge Rate = TRUE
8:32:42.234 L 4 rw- Bool 1 Config\Qsig\Charge Interim = TRUE
8:32:42.234 L 4 rw- Bool 1 Config\Qsig\Charge Final = TRUE
8:32:42.234 L 4 rw- Bool 1 Config\Qsig\Charge in Setup = FALSE
8:32:42.234 L 4 rw- Bool 1 Config\Qsig\Transp Facility = FALSE
8:32:42.234 L 4 rw- Bool 1 Config\Qsig\No Rerouting = FALSE
8:32:42.234 L 4 rw- Bool 1 Config\Qsig\PrInvite = FALSE
8:32:42.234 L 4 rw- Bool 1 Config\Qsig\EricssonMWI = FALSE
8:32:42.234 L 4 rw- UInt 1 Config\Qsig\QSIGDialect = 3
8:32:42.234 L 4 r-- Dir 1 Config\Supplementary Values
8:32:42.234 L 4 rw- UInt 1 Config\Supplementary Values\TSC-CR-Value = 0
8:32:42.234 L 4 rw- Bool 1 Config\Supplementary Values\TSC-CR-Enable = FALSE
8:32:42.234 L 4 rw- Bool 1 Config\Supplementary Values\use first RDN = TRUE
8:32:42.234 L 4 rw- Bool 1 Config\Supplementary Values\ETSI MWI REG = TRUE
8:32:42.234 L 4 rw- UInt 2 Config\Supplementary Values\CCBS Rel Timer = 15
8:32:42.234 L 4 rw- Bool 1 Config\Supplementary Values\ETSI ECT auto = FALSE
8:32:42.234 L 4 rw- Bool 1 Config\Supplementary Values\ETSI ECT forceimpl = TRUE
8:32:42.234 L 4 rw- Bool 1 Config\Supplementary Values\ETSI ECT forceexpl = FALSE
8:32:42.234 L 4 rw- UInt 1 Config\Supplementary Values\ETSI ECT LinkIdfailcount = 0
8:32:42.234 L 4 rw- Bool 1 Config\Supplementary Values\ETSI SWISS Name = FALSE
8:32:42.234 L 4 rw- HInt 4 Config\Supplementary Values\SSFeatures = 0x00000000
8:32:42.234 L 4 rw- UInt 1 Config\Version = 0
8:32:42.234 L 4 rw- UInt 1 Config\DID-Length = 4
8:32:42.234 L 4 rw- Bool 1 Config\Ringertone = FALSE
8:32:42.234 L 4 rw- UInt 2 Config\Alert-Timeout = 0
8:32:42.234 L 4 rw- UInt 2 Config\Redial-Timeout = 0
8:32:42.234 L 4 rw- UInt 1 Config\Redial-Attempts = 0
8:32:42.234 L 4 rw- Bool 1 Config\NT = FALSE
8:32:42.234 L 4 r-- Bool 1 Config\PRI = FALSE
8:32:42.234 L 4 rw- Bool 1 Config\GlobalCRs = TRUE
8:32:42.234 L 4 rw- Bool 1 Config\NoOrderCheck = FALSE
8:32:42.234 L 4 rw- Bool 1 Config\NT-2 = TRUE
8:32:42.234 L 4 r-- BitFld 4 Config\UnChBMask = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.234 L 4 r-- UInt 2 Config\CardType = 53
8:32:42.234 L 4 r-- UInt 4 Config\SerialNumber = 11841
8:32:42.234 L 4 r-- HInt 2 Config\BoardRevision = 0x0000
8:32:42.234 L 4 r-- UInt 2 Config\SubFunction = 0
8:32:42.234 L 4 r-- BitFld 4 Config\DSPState = 0000:0000:0000:0000:0000:0000:0000:0011
8:32:42.234 L 4 r-- Dir 13 Config\SPID-1
8:32:42.250 L 4 rw- Bool 1 Config\SPID-1\Automatic TEI = FALSE
8:32:42.250 L 4 r-- UInt 1 Config\SPID-1\TEI = 0
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-1\SPID = ""
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-1\Number = ""
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-1\Sub-Adr = ""
8:32:42.250 L 4 r-- UInt 2 Config\SPID-1\Global-MWI = 0
8:32:42.250 L 4 r-- Dir 13 Config\SPID-2
8:32:42.250 L 4 rw- Bool 1 Config\SPID-2\Automatic TEI = TRUE
8:32:42.250 L 4 r-- UInt 1 Config\SPID-2\TEI = 0
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-2\SPID = ""
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-2\Number = ""
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-2\Sub-Adr = ""
8:32:42.250 L 4 r-- UInt 2 Config\SPID-2\Global-MWI = 0
8:32:42.250 L 4 r-- Dir 13 Config\SPID-3
8:32:42.250 L 4 rw- Bool 1 Config\SPID-3\Automatic TEI = TRUE
8:32:42.250 L 4 r-- UInt 1 Config\SPID-3\TEI = 0
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-3\SPID = ""
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-3\Number = ""
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-3\Sub-Adr = ""
8:32:42.250 L 4 r-- UInt 2 Config\SPID-3\Global-MWI = 0
8:32:42.250 L 4 r-- Dir 13 Config\SPID-4
8:32:42.250 L 4 rw- Bool 1 Config\SPID-4\Automatic TEI = TRUE
8:32:42.250 L 4 r-- UInt 1 Config\SPID-4\TEI = 0
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-4\SPID = ""
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-4\Number = ""
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-4\Sub-Adr = ""
8:32:42.250 L 4 r-- UInt 2 Config\SPID-4\Global-MWI = 0
8:32:42.250 L 4 r-- Dir 13 Config\SPID-5
8:32:42.250 L 4 rw- Bool 1 Config\SPID-5\Automatic TEI = TRUE
8:32:42.250 L 4 r-- UInt 1 Config\SPID-5\TEI = 0
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-5\SPID = ""
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-5\Number = ""
8:32:42.250 L 4 rw- Ascii 1 Config\SPID-5\Sub-Adr = ""
8:32:42.250 L 4 r-- UInt 2 Config\SPID-5\Global-MWI = 0
8:32:42.250 L 4 r-- Dir 13 Config\SPID-6
8:32:42.265 L 4 rw- Bool 1 Config\SPID-6\Automatic TEI = TRUE
8:32:42.265 L 4 r-- UInt 1 Config\SPID-6\TEI = 0
8:32:42.265 L 4 rw- Ascii 1 Config\SPID-6\SPID = ""
8:32:42.265 L 4 rw- Ascii 1 Config\SPID-6\Number = ""
8:32:42.265 L 4 rw- Ascii 1 Config\SPID-6\Sub-Adr = ""
8:32:42.265 L 4 r-- UInt 2 Config\SPID-6\Global-MWI = 0
8:32:42.265 L 4 r-- Dir 13 Config\SPID-7
8:32:42.265 L 4 rw- Bool 1 Config\SPID-7\Automatic TEI = TRUE
8:32:42.265 L 4 r-- UInt 1 Config\SPID-7\TEI = 0
8:32:42.265 L 4 rw- Ascii 1 Config\SPID-7\SPID = ""
8:32:42.265 L 4 rw- Ascii 1 Config\SPID-7\Number = ""
8:32:42.265 L 4 rw- Ascii 1 Config\SPID-7\Sub-Adr = ""
8:32:42.265 L 4 r-- UInt 2 Config\SPID-7\Global-MWI = 0
8:32:42.265 L 4 r-- Dir 13 Config\SPID-8
8:32:42.265 L 4 rw- Bool 1 Config\SPID-8\Automatic TEI = TRUE
8:32:42.265 L 4 r-- UInt 1 Config\SPID-8\TEI = 0
8:32:42.265 L 4 rw- Ascii 1 Config\SPID-8\SPID = ""
8:32:42.265 L 4 rw- Ascii 1 Config\SPID-8\Number = ""
8:32:42.265 L 4 rw- Ascii 1 Config\SPID-8\Sub-Adr = ""
8:32:42.265 L 4 r-- UInt 2 Config\SPID-8\Global-MWI = 0
8:32:42.265 L 4 rw- UInt 1 Config\L2LinkCount = 1
8:32:42.265 L 4 rw- UInt 1 Config\CPN-Length = 21
8:32:42.265 L 4 r-- UInt 1 Config\BChannelCount = 2
8:32:42.265 L 4 *** Management dump - END ***
8:32:42.265 L 5 *** Management dump - BEGIN Diva Server 4BRI-8M 2.0 PCI #11841-3 ***
8:32:42.265 L 5 r-- UInt 2 Info\CardType = 53
8:32:42.265 L 5 r-- UInt 4 Info\SerialNumber = 11841
8:32:42.265 L 5 r-- Number 1 Info\HW_InfoStruct = 00
8:32:42.265 L 5 r-- UInt 1 Info\InterfaceNr = 2
8:32:42.265 L 5 r-- UInt 2 Info\BoardRevision = 0
8:32:42.265 L 5 r-- UInt 2 Info\SubFunction = 0
8:32:42.265 L 5 r-- UInt 2 Info\SubDevice = 20
8:32:42.265 L 5 r-- AsciiZ 58 Info\ProtocolBuild = "TE_DMLT, Build 106-112, Protocol 6.03(V16) 105-2 [F#00FF]"
8:32:42.265 L 5 r-- AsciiZ 53 Info\DSPCodeBuild = "DIVA Server BRI 2M Kernel Version 1.00 Build 106-642"
8:32:42.265 L 5 r-- Bool 1 Info\PRI = FALSE
8:32:42.265 L 5 r-- UInt 1 Info\Channels = 2
8:32:42.265 L 5 r-- UInt 1 Info\AnalogChannels = 2
8:32:42.265 L 5 r-- Bool 4 Info\PCIDMA = TRUE
8:32:42.265 L 5 r-- Exec 0 Info\IdentifyStart
8:32:42.265 L 5 r-- BitFld 4 Info\DSPState = 0000:0000:0000:0000:0000:0000:0000:0011
8:32:42.281 L 5 r-- Dir 1 Config\US-EKTS
8:32:42.281 L 5 rw- UInt 1 Config\US-EKTS\CACH Appearances = 0
8:32:42.281 L 5 rw- Bool 1 Config\US-EKTS\Force-Alert = FALSE
8:32:42.281 L 5 rw- HInt 1 Config\US-EKTS\Key BeginConf = 0x00
8:32:42.281 L 5 rw- HInt 1 Config\US-EKTS\Key DropConf = 0x00
8:32:42.281 L 5 rw- HInt 1 Config\US-EKTS\Key VoiceMail = 0x01
8:32:42.281 L 5 rw- HInt 1 Config\US-EKTS\Key CallTransfer = 0x00
8:32:42.281 L 5 rw- Bool 1 Config\US-EKTS\Disable AutoSPID = FALSE
8:32:42.281 L 5 r-- Dir 1 Config\DChannel
8:32:42.281 L 5 r-- AsciiZ 9 Config\DChannel\Name = "NONE(20)"
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\E-DSS1 (EURO)
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\FRANCE (VN3)
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\FRANCE (VN6)
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\BELGIUM
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\DMS (Nortel)
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\5ESS Custom
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\JAPAN
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\ITALY
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\TAIWAN
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\AUSTRALIA
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\NEWZEALAND
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\HONGKONG
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\5ESS NI Lucent
8:32:42.281 L 5 r-- Exec 0 Config\DChannel\QSIG
8:32:42.281 L 5 rw- UInt 1 Config\DChannel\Protocol = 20
8:32:42.281 L 5 r-- AsciiZ 22 Config\DChannel\Release = "17:10:34, Jun 29 2006"
8:32:42.281 L 5 r-- Dir 1 Config\Layer3
8:32:42.281 L 5 rw- UInt 1 Config\Layer3\RejectCauseNoListen = 0
8:32:42.281 L 5 rw- UInt 1 Config\Layer3\RejectCauseIgnore = 0
8:32:42.281 L 5 rw- UInt 1 Config\Layer3\DiscAfterProgress = 0
8:32:42.281 L 5 rw- Number 1 Config\Layer3\CHI Interfaceident = 00
8:32:42.281 L 5 rw- UInt 1 Config\Layer3\CLIOrder = 0
8:32:42.281 L 5 rw- UInt 1 Config\Layer3\SdncmplMin = 4
8:32:42.281 L 5 rw- UInt 1 Config\Layer3\ProgressToneProt = 1
8:32:42.281 L 5 r-- Dir 1 Config\Layer2
8:32:42.296 L 5 r-- AsciiZ 17 Config\Layer2\Stable L2 = "Send No Disc (1)"
8:32:42.296 L 5 r-- Exec 0 Config\Layer2\On demand (0)
8:32:42.296 L 5 r-- Exec 0 Config\Layer2\Send No Disc (1)
8:32:42.296 L 5 r-- Exec 0 Config\Layer2\Permanent (2)
8:32:42.296 L 5 rw- UInt 1 Config\Layer2\L2 = 1
8:32:42.296 L 5 r-- Dir 1 Config\Layer1
8:32:42.296 L 5 r-- HInt 1 Config\Layer1\L1HuntGroupConf = 0x00
8:32:42.296 L 5 rw- UInt 1 Config\Layer1\Part68 Level Lim = 1
8:32:42.296 L 5 rw- Bool 1 Config\Layer1\Recording AGC = FALSE
8:32:42.296 L 5 rw- BitFld 1 Config\Layer1\Dial Pulse Det. = 0000:0000
8:32:42.296 L 5 rw- Bool 1 Config\Layer1\DTMF Suppressor = FALSE
8:32:42.296 L 5 rw- Bool 1 Config\Layer1\LI Via Host Mem. = FALSE
8:32:42.296 L 5 rw- Bool 1 Config\Layer1\Conf. AGC Enable = TRUE
8:32:42.296 L 5 rw- UInt 2 Config\Layer1\Conf. AGC MinPart = 4
8:32:42.296 L 5 rw- HInt 2 Config\Layer1\Conf. AGC Thresh = 0x0100
8:32:42.296 L 5 r-- Dir 1 Config\B-Layer1
8:32:42.296 L 5 rw- BitFld 4 Config\B-Layer1\Disabled DSPs = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.296 L 5 r-- Dir 1 Config\Modem
8:32:42.296 L 5 rw- BitFld 1 Config\Modem\Protocol Neg. = 0000:0000
8:32:42.296 L 5 rw- BitFld 1 Config\Modem\Protocol Opt. = 0000:0000
8:32:42.296 L 5 rw- UInt 1 Config\Modem\Break Config. = 0
8:32:42.296 L 5 rw- UInt 2 Config\Modem\Validation Chars = 0
8:32:42.296 L 5 rw- BitFld 1 Config\Modem\Line Taking Opt. = 0000:0000
8:32:42.296 L 5 rw- UInt 1 Config\Modem\Negotiation Mode = 0
8:32:42.296 L 5 rw- UInt 1 Config\Modem\Guard Tone = 0
8:32:42.296 L 5 rw- BitFld 1 Config\Modem\Modulation Opt. = 0000:0000
8:32:42.296 L 5 rw- BitFld 2 Config\Modem\Disabled Mod. = 0000:0000:0000:0000
8:32:42.296 L 5 rw- BitFld 1 Config\Modem\Enabled Mod. = 0000:0000
8:32:42.296 L 5 rw- UInt 2 Config\Modem\TX Min Speed = 0
8:32:42.296 L 5 rw- UInt 2 Config\Modem\TX Max Speed = 0
8:32:42.296 L 5 rw- UInt 2 Config\Modem\RX Min Speed = 0
8:32:42.296 L 5 rw- UInt 2 Config\Modem\RX Max Speed = 0
8:32:42.296 L 5 rw- BitFld 1 Config\Modem\Disabled Symb. = 0000:0000
8:32:42.296 L 5 rw- BitFld 1 Config\Modem\INFO Options = 0000:0000
8:32:42.296 L 5 rw- UInt 1 Config\Modem\TX Level Adj. = 0
8:32:42.296 L 5 rw- UInt 1 Config\Modem\Speaker Control = 0
8:32:42.296 L 5 rw- UInt 1 Config\Modem\Speaker Volume = 0
8:32:42.296 L 5 rw- UInt 1 Config\Modem\Carrier Wait sec. = 0
8:32:42.296 L 5 rw- UInt 1 Config\Modem\Carrier Loss 10th = 0
8:32:42.296 L 5 rw- UInt 1 Config\Modem\DCD ON Threshold = 0
8:32:42.296 L 5 rw- HInt 2 Config\Modem\Eye Setup = 0x0000
8:32:42.296 L 5 r-- Dir 1 Config\Modem\Proprietary
8:32:42.312 L 5 rw- BitFld 2 Config\Modem\Proprietary\Options = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 4 Config\Modem\Proprietary\Enabled Mod. = 0000:0000:0000:0000:0000:0000:0000:0000
8:32:42.312 L 5 rw- UInt 2 Config\Modem\Proprietary\Echo Suppress ms = 0
8:32:42.312 L 5 rw- UInt 2 Config\Modem\Proprietary\Preamble Time ms = 0
8:32:42.312 L 5 rw- UInt 2 Config\Modem\Proprietary\Clean Carrier ms = 0
8:32:42.312 L 5 rw- UInt 2 Config\Modem\Proprietary\Validation Chars = 0
8:32:42.312 L 5 rw- BitFld 2 Config\Modem\Proprietary\Async Format 1 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\Modem\Proprietary\Async Format 2 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\Modem\Proprietary\Async Format 3 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\Modem\Proprietary\Async Format 4 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\Modem\Proprietary\Async Format 5 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\Modem\Proprietary\Async Format 6 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\Modem\Proprietary\Async Format 7 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\Modem\Proprietary\Async Format 8 = 0000:0000:0000:0000
8:32:42.312 L 5 r-- Dir 1 Config\FAX
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Options = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Options2 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- UInt 2 Config\FAX\Min Speed = 0
8:32:42.312 L 5 rw- UInt 2 Config\FAX\Max Speed = 0
8:32:42.312 L 5 rw- BitFld 1 Config\FAX\Disabled Res. = 0000:0000
8:32:42.312 L 5 rw- UInt 1 Config\FAX\Record. Width = 0
8:32:42.312 L 5 rw- UInt 1 Config\FAX\Record. Length = 0
8:32:42.312 L 5 rw- UInt 1 Config\FAX\Scanline Time = 0
8:32:42.312 L 5 rw- UInt 1 Config\FAX\TX Level Adj. = 0
8:32:42.312 L 5 rw- UInt 2 Config\FAX\Max Overhead sec. = 0
8:32:42.312 L 5 rw- BitFld 1 Config\FAX\Disabled Symb. = 0000:0000
8:32:42.312 L 5 rw- BitFld 1 Config\FAX\INFO Options = 0000:0000
8:32:42.312 L 5 r-- Dir 1 Config\FAX\Font
8:32:42.312 L 5 rw- HInt 1 Config\FAX\Font\Code = 0x00
8:32:42.312 L 5 r-- Exec 0 Config\FAX\Font\Read
8:32:42.312 L 5 r-- Exec 0 Config\FAX\Font\Write
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Font\Row1 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Font\Row2 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Font\Row3 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Font\Row4 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Font\Row5 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Font\Row6 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Font\Row7 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Font\Row8 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Font\Row9 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Font\Row10 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Font\Row11 = 0000:0000:0000:0000
8:32:42.312 L 5 rw- BitFld 2 Config\FAX\Font\Row12 = 0000:0000:0000:0000
 
Hi.

During a call scenario B-channels from ISDN trunk with XPR (TGRP 4)goes in BUSY state ?
DIS-SDSU:ALL,,PEN,PER3,1,1,55;
or
DIS-BUEND:4,b;

SEGMENT=8 is ok in TDCSU.

Did you try to restart the whole board 1-1-5 (RES-BSSU)?

In which format is set the Voicemail number on a extension when you forward it (unconditional,busy,no reply) to XPR ?
Normally it should be national format:
e.g. extension 123 -> CFNR to his Voice mail : 00 211 899 (15) 123
0 -> TIE code in Wabe for access to extern
0211 -> Area code
899 -> Local code
15 - TIE code in Wabe for trunk with XPR
123 - extension number

Please have a look also on :


Some additional COT param. which might help (from standard XPR trunk config):
RECALL IF USER HANGS UP IN CONSULTATION CALL - RCL
TRUNK CALL TRANSFER - XFER
ATTENDANT INTERCEPT WHEN BUSY - IBSY
ATTENDANT INTERCEPT WHEN FREE (AFTER TIMEOUT) - IFR
KNOCKING OVERRIDE POSSIBLE - KNOR
CALL EXTEND ONLY FOR CALL STATE - CEOC
NETWORKWIDE AUTOMATIC CALLBACK ON BUSY - CBBN
NETWORKWIDE AUTOMATIC CALLBACK ON FREE - CBFN
REGISTRATION OF IMPLAUSIBLE EVENTS - IEVT
TRANSFER OF USER ITR GROUPS VIA S0/S2 (NWU) - ITRN
INCOMING CIRCUIT FROM SYSTEM WITHOUT LCR - NLCR
ANNOUNCEMENT ON BUSY OR NO ANSWER - ABNA
WAIT ANNOUNCEMENT - WAAN
INCOMING CIRCUIT FROM SYSTEM WITHOUT LCR (DATA) - NLRD
TRANSFER ALLOWED WITHOUT DISCONNECT SUPERVISION - TWDS
AUTOM.DTMF CONVERSION ON INCOM.CALL WHILE IN TALK STATE - AMFC
NO TONE - NTON
TSC-SIGNALING FOR NETWORKWIDE FEATURES (MANDATORY)- TSCS

Mandatory COP param:
LINE WITH START-DIAL-SIGNAL - SDL
SPECIAL MODE - SFRM
REGISTRATION OF LAYER 3 ADVISORIES - L3AR
START-DIALING-SIGNAL TIMER 1 (AMO DTIM2: PARAMETER STADIAL1) - TIM1
MAKE/BREAK RATIO FOR DTMF 1 (PULSE=80MS,PAUSE=80MS) - DTM1

Check also PMIDX in SBCSU to be synchronized with RICHT:pM - IDX
 
ok I have got it so that xpressions answers, but it does not work as expected. I will probably have to reset it up.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top