Tie Line Transfer 2

[mt6322]

This is a follow-up post and request for additional help.

We setup a tie line between 2 sites. When we receive an inbound call via local the PRI circuit connected to its each site and transfer the call to the remote site via the tie line, the call goes through. But when we make an outbound call local/long distance call from either site via the PRI lines and then when the call is transferred to the remote site the call will immediately cut-off. What do I have to change to allow transfer of outbound calls to the tie line. Thanks for your advise.

 

[johnpoole]

is that tie internal? rcls prompt in the cdb and does the targ on the tie match the tie on the outbound trunk. either one can cause ablock

john poole
bellsouth business
columbia,sc

 

[mt6322]

Thanks for the response.
No targ on the routes.

I have read all of the posts/threads on this site regarding trunk to trunk access problem and no seemed to have resolved the issue when you make an outside call from your local/long distance access trunk and then transfer the call over to the T1 tie trunk, you can complete the transfer. What should be settings on my routes, trunks and the DN to allow such a transfer ?

If you have experienced this problem and were able to resolve this issue, could you please let me know what programming changes that I have to make on my switch. I appreciate all the help that you can provide. Thanks a lot.

 

[johnpoole]

route

TYPE RDB
CUST 00
ROUT 93
DES  TO 11
TKTP TIE
NPID_TBL_NUM   0
ESN  NO
CNVT NO
SAT  NO
IDEF NET
[COLOR=red][b]RCLS INT[/b][/color]
VTRK NO
DTRK YES
BRIP NO
DGTP DTI
ISDN NO
DSEL VCE
PTYP DTT
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 5998
TARG
CLEN 1
BILN NO
OABS
INST
IDC  YES
DCNO 1 *
NDNO 1
DEXT NO
DNAM NO
ANTK
SIGO STD
STYP SDAT
TIMR ICF  512
     OGF  512
     EOD  13952
     DSI  34944
     NRD  10112
     DDL  70
     ODT  4096
     RGV  640
     GRD  896
     SFB  3

     IENB  5
     TFD  0
     VSS  0
     VGD  6
SST  5 0
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR  YES


PAGE 002

INC  YES
LAST YES
QREC YES
OAL  YES
AIA  YES
OAN  YES
OPD  NO
CDRX NO
NATL YES
VRAT NO
MUS  YES
MRT  81
RACD NO
MANO NO
EQAR NO
FRL  0 0
FRL  1 0
FRL  2 0
FRL  3 0
FRL  4 0
FRL  5 0
FRL  6 0
FRL  7 0
OHQ  NO
OHQT 00
CBQ  NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART  0
SGRP 0
AACR NO

caompare a route that does not have that problem.. that single prompt will cause strange problems..

john poole
bellsouth business
columbia,sc

 

[mt6322]

Thanks John. After changing the RCLS prompt from EXT to INT on the T1 tie route (DGTP=DTI), I could now transfer external calls over the tie line.

But on the tie trunk with D channel using CDP, route configured as DGTP=PRI, RCLS=INT, I still could not tranfer external calls. Any ideas, please ? Thank you.

 

[informidicate]

Is trunk to trunk transfer enabled in CDB NET DATA