Dears Hi
I'm managing a Hipath 4000 V6 with A PRI-E1 connection to an old Mitel PBX.
The PRI-E1 is connected with the following command lines on the Hipath side:
ADD-BUEND:7,"MITEL ",30,0,*,1,ON,0,0,NEUTRAL;
ADD-TDCSU:OPT=NEW,PEN=1-05-014-1,COTNO=5,COPNO=5,DPLN=0,ITR=0,COS=5,LCOSV=1,LCOSD=1,CCT="TO MITEL ",DESTNO=0,PROTVAR=ECMAV2,SEGMENT=1,DEDSVC=NONE,TRTBL=GDTR,SIDANI=N,ATNTYP=TIE,CBMATTR=NONE,TCHARG=N,SUPPRESS=0,TRACOUNT=10,SATCOUNT=MANY,ALARMNO=0,FIDX=1,CARRIER=1,ZONE=EMPTY,COTX=5,FWDX=1,CHIMAP=N,UUSCCX=16,UUSCCY=8,FNIDX=1,NWMUXTIM=10,CLASSMRK=EC&G711&G729AOPT,TGRP=7,SRCHMODE=CIR,INS=Y,SECLEVEL=TRADITIO,HMUSIC=0,DEV=S2CONN,BCHAN=1&&30,BCNEG=N,BCGR=1,LWPAR=0,LWPP=0,LWLT=0,LWPS=0,LWR1=0,LWR2=0;
M2 1 ADD-LODR:2,,,,NPI,ISDN,NATIONAL;
M2 1 ADD-LODR:2,,,,ECHOALL;
M2 1 ADD-LODR:2,,,,END;
ADD-LDAT:LROUTE=7,LSVC=ALL,LVAL=1,TGRP=7,ODR=2,LAUTH=1,CARRIER=1,ZONE=EMPTY,LATTR=WCHREG&PUBNUM,DNNO=10,VCCYC=4;
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP="A"-"X"-"X",DPLN=0&1&2&3&4&5&6&7&8&9&10&11&12&13&14&15,LROUTE=1,LAUTH=1,PINDP=N;
ADD-LDPLN:LCRPATT,0,98-XX,0&1&2&3&4&5&6&7&8&9&10&11&12&13&14&15,7,,,1,,,,N;
Mithel PBX Manager says that there are not many changes to do and they won't make any changes even if they could.
The problem is as follows:
Calls from Hipath to Mitel are connected in the first 15 channels of PRI Link properly but when it reaches the 16th channel the ring is sent to the destination number and no voice is transmitted.
same problem persists until calls rich 30th channel.
Then the call returns to the first channel and it is OK again.
I know Mithel is using the 16th and 32nd channels for signaling but how to set it up in Hipath 4000?
Any help would be appreciated.
Best regards
Hamid
I'm managing a Hipath 4000 V6 with A PRI-E1 connection to an old Mitel PBX.
The PRI-E1 is connected with the following command lines on the Hipath side:
ADD-BUEND:7,"MITEL ",30,0,*,1,ON,0,0,NEUTRAL;
ADD-TDCSU:OPT=NEW,PEN=1-05-014-1,COTNO=5,COPNO=5,DPLN=0,ITR=0,COS=5,LCOSV=1,LCOSD=1,CCT="TO MITEL ",DESTNO=0,PROTVAR=ECMAV2,SEGMENT=1,DEDSVC=NONE,TRTBL=GDTR,SIDANI=N,ATNTYP=TIE,CBMATTR=NONE,TCHARG=N,SUPPRESS=0,TRACOUNT=10,SATCOUNT=MANY,ALARMNO=0,FIDX=1,CARRIER=1,ZONE=EMPTY,COTX=5,FWDX=1,CHIMAP=N,UUSCCX=16,UUSCCY=8,FNIDX=1,NWMUXTIM=10,CLASSMRK=EC&G711&G729AOPT,TGRP=7,SRCHMODE=CIR,INS=Y,SECLEVEL=TRADITIO,HMUSIC=0,DEV=S2CONN,BCHAN=1&&30,BCNEG=N,BCGR=1,LWPAR=0,LWPP=0,LWLT=0,LWPS=0,LWR1=0,LWR2=0;
M2 1 ADD-LODR:2,,,,NPI,ISDN,NATIONAL;
M2 1 ADD-LODR:2,,,,ECHOALL;
M2 1 ADD-LODR:2,,,,END;
ADD-LDAT:LROUTE=7,LSVC=ALL,LVAL=1,TGRP=7,ODR=2,LAUTH=1,CARRIER=1,ZONE=EMPTY,LATTR=WCHREG&PUBNUM,DNNO=10,VCCYC=4;
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP="A"-"X"-"X",DPLN=0&1&2&3&4&5&6&7&8&9&10&11&12&13&14&15,LROUTE=1,LAUTH=1,PINDP=N;
ADD-LDPLN:LCRPATT,0,98-XX,0&1&2&3&4&5&6&7&8&9&10&11&12&13&14&15,7,,,1,,,,N;
Mithel PBX Manager says that there are not many changes to do and they won't make any changes even if they could.
The problem is as follows:
Calls from Hipath to Mitel are connected in the first 15 channels of PRI Link properly but when it reaches the 16th channel the ring is sent to the destination number and no voice is transmitted.
same problem persists until calls rich 30th channel.
Then the call returns to the first channel and it is OK again.
I know Mithel is using the 16th and 32nd channels for signaling but how to set it up in Hipath 4000?
Any help would be appreciated.
Best regards
Hamid