T1 problem 1

[acewarlock]

I have a T1 that keeps going up and down and Qwest is telling me I need to change my protcol to NI1 from NI2 as they don't support NI2 on there DMS. To change this do I need to remove the Loop fron the CFN before I can out the trunks and then out the RDB so I can rebuild the RDB with NI1?

 

[Dougo123]

I believe you just need to disable the loop and can leave the loop in cfn.

 

[acewarlock]

I have the loop disable, now do I change it, I can't get to the prompt to change it.?

 

[Dougo123]

What do you want to change on the loop Ace? If your just doing a IFC chg you can just go to LD 16 and use the chg command there

 

[acewarlock]

I just want to change NI2 to NI1.

 

[acewarlock]

How do I get to IFC the prompt keeps jumping over it.

 

[Dougo123]

You might have to out the rdb and rebuild, but I don't even see NI1 on the list. I think D100 is close though.

 

[bigindian65]

ACE you have Dchs on this? IFC on the Dchs too. If so, I think you do have out and rebuild (if doing the Dch)


TYPE RDB
CUST 00
ROUT 0
DES LOCAL
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES say YES
MODE PRA
IFC D100 (chg to NI2)
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
DSEL VCE
PTYP PRI
AUTO NO


ADAN DCH 10
CTYP MSDL
GRP 0
DNUM 11
PORT 0
DES
USR PRI
DCHL 18
OTBF 127
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC D100 *** NI2 chg here, (rebuild rather)
SIDE USR
CNEG 1
RLS ID 36

 

[acewarlock]

I do have a DCH on this route.

DES QWESTLD
TKTP DID
NPID_TBL_NUM 0
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2 I want to change this to NI1
CBCR NO
NCOS 0
SBN NO
PNI 00000

 

[johnpoole]

to change that out the trunks, and the route the do the change.. be sure to down the dch/msdl and enl the msdl fdl to write that to the card

john poole
bellsouth business
columbia,sc

 

[Dougo123]

When you change the Dch you're going to need to do a FDL on it to make it stick

 

[acewarlock]

Just looking at the NTP's and NI1 isn't listed, so I guess i'll need to ask Qwest what switch model DMS they have.

 

[acewarlock]

Never had to remove a PRI before.

Loop is disabled
DCH is disabled
When I try to out the DID trunk I enter 6 0 for the TN and

I get SCH0620

Input out of range (Overlay 15)
Action Re-enter input

 

[bigindian65]

out in 14

out 23

6 0

will take out 23 members in incremintal order

 

[acewarlock]

Thats the problem, I keep getting the SCH0620.

 

[bigindian65]

6 1 !! not 6 0

 

[acewarlock]

I'll be damed, leave it to Nortel to mess with your head, every thing else is UNIT 0. that worked.

thanks Have a star on me.

 

[bigindian65]

Thanks Ace, cool coming from a TOP MVP. I was racking my brain because I have seen that before...like every time I freak'in out members! Then, I still agreed with you at first...stupid 1 thru 23 route trunk members. I've smoked the first member of the next trunk before doing an out 24 on a T with a Dch instead of out 23.

 

[acewarlock]

I don't care how long i've been doing this, I still learn something new every day and anybody who say's they know it all is a fool.

 

[acewarlock]

OK I rebuilt the RDB with IFC SL1, when I try to build the trunks I get SCH4792 Basicly telling me to FDL the DCH.

I ENL DCH 11 FDL and it downloads the the NI2 DATA again.

How do I get it to download the SL1 DATA?