Switch issues ring generator and line card going out 2

[dawg2]

I have an option 61c , and aout 12 days ago I had a ring generator go out on my 20 shelf, after looking up guides I i shout down the 20 shelf...... then turn on and the ring generator came back, a few days later the RG light went on the 24 shelf (same colum, this time I shut down both shelfs and they reset. Over the weekend on the 20 shelf I lost an entire analog card had to move 16 phones, left 1 unit on bad card and this morning it was disabled. Any ideas on what I need to do? Also can you tell me the commands on how to remove the bad card and then install a new?

Thank you this site is very helpful and you are all great to take the time to assist others!

 

[GHTROUT]

To replace a line card, just

>LD 32
.DISC L S C (Loop, Shelf, Card)
Then swap the card...Then
>LD 32
.ENLC L S C (Loop, Shelf, Card)

Done.

To replace the Ring Generator, power down the shelf, replace the card, power up the shelf.

--
GHTROUT.com - Help for Nortel Meridian/CS1000 System Administrators
--

 

[EddieDuece]

If you have a bad analog card, it will cause a issue with the ring generator. Try replacing the faulty analog card.

 

[dawg2]

Thank you, so you think that if I remove the bad analogue card this could be my problem?

Thank you so much!!

 

[EddieDuece]

If your ring generator is not bad, this should take care of your issue.

 

[bhassell2000]

I have had a defective PDU in a AC powwered pedestal make a ring generator not work and had me stumped for a few days

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/pub/buddy-hassell/7/5a5/b8b

 

[dawg2]

I now have the ring generator going out on the 24 shelf same colum, Need to repair I have a new RG card just not sure what shelf to replace, had issues on both shelfs. I have read several post, IN ld 137
>ld 137
CIOD000
.stat

IOP 0 ENABLED (ACTIVE)
IOP 1 ENABLED (STANDBY: S/W STATUS)
CMDU 0 ENABLED (ACTIVE)
CMDU 1 DISABLED (No Access to HDK)
RDUN DISABLED
ELNK ENABLED

Any ideas on how to have stop happening. Please send command lines for testing or setting.

Thank you

 

[Firebird Scrambler]

Can you print out the systems history file as this should give us some clues?.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[bhassell2000]

Is this an AC powered system?

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/pub/buddy-hassell/7/5a5/b8b

 

[dawg2]

Is this what you are asking for:


>ld 22
PT2000

REQ phst

SCH0101

REQ prt
TYPE phst
FILE 4% FULL
%
% DTC001
%
% AUD000
%
% DTC001
%
% TTY #05 LOGGED OUT 12:55 11/9/2010
% SESSION DURATION: 00:29
%
% AUD000
%
% DTC001
%
% TIM030 13:00 11/9/2010 CPU 0
%
% TTY #05 LOGGED IN 13:02 11/9/2010
%
% TTY #05 LD 022 13:02 48 11/9/2010

 

[dawg2]

I did do a shut down and and R & R ring generator card on the 24 shelf. As I know everything came back up. I did shut both shelfs in the colum down 20 & 24. Everything is back up and working forgot about 2616 losing forwards...


REQ prt
TYPE ahst
% SOCKET ID BLK
% TIME
% CPND
% CPND NM
% SPECIFIC DATA
% HI
% ALARM_MGT
% CHECKING
%
% RECORD COUNT = 0219
% DATADUMP COMPLETE
%
% Starting database backup
% to floppy diskette on CMDU 0
% DIRECTORY
% CONFIG
% DATA
% HI
% Database backup complete!
%
% DROL001 DAILY ROUTINE END
% DUMP LD43 END 00:06 11/9/2010
%
% DROL000 DAILY ROUTINE BEGIN
% AUDIT LD44 BEGIN 00:06 11/9/2010
%
% AUD000
%
% DROL001 DAILY ROUTINE END
% AUDIT LD44 END 00:07 11/9/2010
%
% DROL000 DAILY ROUTINE BEGIN
% DTIM LD60 BEGIN 00:07 11/9/2010
%
% DTI TRK LOOP 12 ATLP 0
% SLFT OK
% TRSH CNT:
% BPV -000
% SLIPD -000
% SLIPR -000
% LOSFA -000
% OS_BPV -000
% OS_LOSFA-000
% OS_YEL -000
%
% PRI TRK LOOP 14 ATLP 0
% SLFT OK
% TRSH CNT:
% BPV -000
% SLIPD -000
% SLIPR -952
% CRC -000
% LOSFA -000
% OS_BPV -000
% OS_LOSFA-000
% OS_YEL -000
%
% PRI TRK LOOP 28 ATLP 0
% SLFT OK
% TRSH CNT:
% BPV -000
% SLIPD -000
% SLIPR -000
% CRC -000
% LOSFA -000
% OS_BPV -000
% OS_LOSFA-000
% OS_YEL -000
%
% DTI TRK LOOP 29 ATLP 0
% SLFT OK
% TRSH CNT:
% BPV -000
% SLIPD -000
% SLIPR -000
% LOSFA -000
% OS_BPV -000
% OS_LOSFA-000
% OS_YEL -000
%
% DROL001 DAILY ROUTINE END
% DTIM LD60 END 00:07 11/9/2010
%
% DROL000 DAILY ROUTINE BEGIN
% CCED LD135 BEGIN 00:07 11/9/2010
%
% DROL001 DAILY ROUTINE END
% CCED LD135 END 00:07 11/9/2010
%
% CCED218 Cannot SCPU: A stdby core resource(s) has a fault
%
% AUD000
%
% DTC001
%
% TIM030 00:15 11/9/2010 CPU 0
%
% DTC001
%
% AUD000
%
% DTC001
%
% DTC001
%
% TIM030 01:00 11/9/2010 CPU 0
%
% AUD000
%
% DTC001
%
% DTC001
%
% AUD000
%
% DTC001
%
% DTC001
%
% TIM030 02:00 11/9/2010 CPU 0
%
% AUD000
%
% DTC001
%
% DTC001
%
% AUD000
%
% DTC001
%
% DTC001
%
% AUD000
%
% TIM030 03:00 11/9/2010 CPU 0
%
% DTC001
%
% DTC001
%
% AUD000
%
% DTC001
%
% AUD000
%
% DTC001
%
% TIM030 04:00 11/9/2010 CPU 0
%
% DTC001
%
% AUD000
%
% DTC001
%
% DTC001
%
% AUD000
%
% DTC001
%
% TIM030 05:00 11/9/2010 CPU 0
%
% DTC001
%
% AUD000
%
% DTC001
%
% DTC001
%
% AUD000
%
% DTC001
%
% TIM030 06:00 11/9/2010 CPU 0
%
% DTC001
%
% AUD000
%
% DTC001
%
% DTC001
%
% AUD000
%
% DTC001
%
% TIM030 07:00 11/9/2010 CPU 0
%
% DTC001
%
% AUD000
%
% DTC001
%
% DTC001
%
% AUD000
%
% DTC001
%
% TIM030 08:00 11/9/2010 CPU 0
%
% DTC001
%
% AUD000
%
% DTC001
%
% TTY #05 LOGGED IN 08:31 11/9/2010
%
% TTY #05 LD 020 08:32 02 11/9/2010
%
% TTY #05 LD 032 08:32 06 11/9/2010
%
% TTY #05 LD 020 08:33 44 11/9/2010
%
% TTY #05 LD 032 08:34 08 11/9/2010
%
% DTC001
%
% AUD000
%
% DTC001
%
% TIM030 09:00 11/9/2010 CPU 0
%
% TTY #05 LOGGED OUT 09:02 11/9/2010
% SESSION DURATION: 00:31
%
% AUD000
%
% DTC001
%
% TTY #05 LOGGED IN 09:17 11/9/2010
%
% TTY #05 LD 037 09:17 46 11/9/2010
% ST
% TIM030 09:17 11/9/2010 CPU 0
%
% TTY #05 LD 032 09:22 04 11/9/2010
%
% TTY #05 LD 043 09:24 22 11/9/2010
%
% DTC001
%
% TTY #05 LD 020 09:30 50 11/9/2010
%
% AUD000
%
% DTC001
%
% TTY #05 LD 037 09:57 52 11/9/2010
%
% DTC001
%
% TIM030 10:00 11/9/2010 CPU 0
%
% AUD000
%
% TTY #05 LD 137 10:08 04 11/9/2010
%
% TTY #05 LD 020 10:19 54 11/9/2010
%
% DTC001
%
% AUD000
%
% DTC001
%
% DTC001
%
% AUD000
%
% TIM030 11:00 11/9/2010 CPU 0
%
% TTY #05 LD 032 11:01 36 11/9/2010
%
% TTY #05 LD 020 11:04 04 11/9/2010
%
% TTY #05 LD 022 11:04 56 11/9/2010
%
% TTY #05 LD 022 11:07 20 11/9/2010
%
% XMI000 24 : XNET cLAN polling failure on port 0
%
% XMI000 20 : XNET cLAN polling failure on port 0
%
% DTC001
%
% XMI000 24 : port 0 XPEC has requested Download
%
% XMI000 20 : port 0 XPEC has requested Download
%
% OVL021 IDLE
%
% SDL100 BUSY
%
% OVL021 IDLE
%
% SDL100 BUSY
%
% OVL021 BKGD
%
% SDL100 BUSY
%
% TIM030 11:16 11/9/2010 CPU 0
%
% SDL000 XPEC 4 (24 0), VERSION 23, BKGD MODE.
%
% XMI002 24 0 0 XUT
%
% XMI002 24 0 1 XUT
%
% XMI002 24 0 3 XDLC
%
% XMI002 24 0 4 XDLC
%
% XMI002 24 0 5 XDLC
%
% XMI002 24 0 6 XDLC
%
% XMI002 24 0 7 XDLC
%
% XMI002 24 0 8 XDLC
%
% XMI002 24 0 9 XDLC
%
% XMI002 24 0 11 XMLC
%
% XMI002 24 0 12 XMLC
%
% XMI002 24 0 13 XMLC
%
% XMI002 24 0 14 XMLC
%
% XMI002 24 0 15 XDTR
%
% OVL021 BKGD
%
% SDL100 BUSY
%
% OVL021 IDLE
%
% SDL100 BUSY
%
% SDL000 XPEC 3 (20 0), VERSION 23, BKGD MODE.
%
% SDL000 XPEC 4 (24 0), VERSION 23, BKGD MODE.
%
% XMI002 24 0 0 XUT
%
% XMI002 20 0 0 XUT
%
% XMI002 24 0 1 XUT
%
% XMI002 20 0 1 XUT
%
% XMI002 24 0 3 XDLC
%
% XMI002 20 0 3 XDLC
%
% XMI002 24 0 4 XDLC
%
% XMI002 20 0 4 XDLC
%
% XMI002 24 0 5 XDLC
%
% XMI002 20 0 5 XDLC
%
% XMI002 24 0 6 XDLC
%
% XMI002 20 0 6 XDLC
%
% XMI002 24 0 7 XDLC
%
% XMI002 20 0 7 XDLC
%
% XMI002 24 0 8 XDLC
%
% AUD000
%
% TTY #05 LD 020 11:18 22 11/9/2010
%
% TTY #05 LD 032 11:18 30 11/9/2010
%
% TTY #05 LD 020 11:18 54 11/9/2010
%
% TTY #05 LD 032 11:19 36 11/9/2010
%
% TTY #05 LD 020 11:19 44 11/9/2010
%
% TTY #05 LD 032 11:23 40 11/9/2010
%
% TTY #05 LD 043 11:24 46 11/9/2010
%
% DTC001
%
% TIM030 11:31 11/9/2010 CPU 0
%
% DTC001
%
% AUD000
%
% DTC001
%
% TIM030 12:00 11/9/2010 CPU 0
%
% TRK150 8 0 1 3
%
% DTC001
%
% TTY #05 LOGGED OUT 12:13 11/9/2010
% SESSION DURATION: 02:55
%
% AUD000
%
% TIM030 12:15 11/9/2010 CPU 0
%
% TTY #05 LOGGED IN 12:27 11/9/2010
%
% TTY #05 LD 022 12:27 26 11/9/2010
%
% DTC001
%
% AUD000
%
% DTC001
%
% TTY #05 LOGGED OUT 12:55 11/9/2010
% SESSION DURATION: 00:29
%
% AUD000
%
% DTC001
%
% TIM030 13:00 11/9/2010 CPU 0
%
% TTY #05 LOGGED IN 13:02 11/9/2010
%
% TTY #05 LD 022 13:02 48 11/9/2010


Any ideas if this was the issue. on the 20 shelf the RG had shut down this is not the 1st time when the last couple of weeks. On Monday I had same is but with 20 shlef though it was a bad analog card so I moved tn and removed card.
Any ideas..... need to get repaired correctly.

Thank you

 

[Firebird Scrambler]

Has any major changes been made to the configuration recently as the errors seem to point to an old reference I've found below. It's not actually the same but it may be on the same track?

A problem developed on a site whereby only one shelf of system was found to be closing down
causing MSF...What was happening was that the controller/nwk card was requesting a download
giving an XMI0000 with the text as above . This suddenly started happening after six SUPV wallboards were fitted apparently ,this problem as been seen before mainly in Europe.

The PROBLEM was found to be that all six w'bds had been prog'd onto supv's on that shelf and with all the extra messaging created the nwk/ctlr cards couldn't handle it.
The SOLUTION is to spread where the switch allows, the wallboards/supv's to be on different loops shelves of the system.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[dawg2]

no major changes the only thing is I have added 2 mck 1100 -analog extenders and ip based extender since march 2010. I am not sure what you mean by:
The PROBLEM was found to be that all six w'bds had been prog'd onto supv's on that shelf and with all the extra messaging created the nwk/ctlr cards couldn't handle it.The SOLUTION is to spread where the switch allows, the wallboards/supv's to be on different loops shelves of the system.
Where and what, would I find this information? Can you give ld and command lines please?

Thank you for your response and help.