setup for germany isdn2 ane isdn 30

[bpg1]

hi all

the promblem is that the co on a local call inside the same city are sending the digits to slow, or one digit later than the others. because from other place it works fine. so if anyone have how to do in germany, i would be grateful.

 

[SL1User]

Hi,

what do you mean to slow or one digit later as the other???

All you have to do is enable at least ovlr=yes on your DCH.

What provider are you using German Telekom ???

That may make the difference.

Installed lots of systems there, never had any trouble.
Unfortunately i have no access to a system from home, so post me what printouts you need.

RDB, DCH, DID or all???

 

[bpg1]

hi sl1user

provider is german telekom, could you send all print out both isdn30 and isdn 2 thank you.

 

[SL1User]

Here we go for the 2meg


ADAN DCH 1
CTYP MSDL
GRP 1
DNUM 4
PORT 1
DES Euro
USR PRI
DCHL 67
OTBF 80
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC EURO
CNTY GER
PINX_CUST 0
ISDN_MCNT 300
CLID OPT1
PROG NCHG
CO_TYPE STD
SIDE USR
CNEG 2
RLS ID **
RCAP COLP MCID
MBGA NO
OVLR YES
DIDD 2
OVLS YES
OVLT 0
T310 120
INC_T306 20
OUT_T306 20
T200 2
T203 20
N200 3
N201 260
K 7


DES
TN 067 01
TYPE DID
CDEN SD
CUST 0
TRK PRI2
PDCA 2
PCML A
NCOS 0
RTMB 8 1
B-CHANNEL SIGNALING
NITE
AST NO
IAPG 0
CLS UNR DIP CND WTA LPR APN THFD BARD
P10 VNL
TKID
DTCR NO
DATE NO DATE

TYPE RDB
CUST 00
ROUT 8
DES AMT
TKTP DID
NPID_TBL_NUM 0
SAT NO
IDEF NET
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC EURO
CNTY GER
SBN NO
PNI 00001
NCNA NO
NCRD NO
ISAR NO
CPFXS YES
SDID NO
DAPC YES
TBL 1
INTC NO
DSEL VOD
PTYP DCO
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
STEP
ACOD 12345
TARG
BILN NO
OABS
INST
IDC YES
DCNO 1
NDNO 1 *
DEXT YES
DNAM YES
MFC NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GTO 2048
GTI 1280
SFB 3
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
SCDT NO
2 DT NO
DRNG NO
CDR NO
CCO NO
NATL YES
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
RACD NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
OPR NO
PRDL NO
EOS NO
DNSZ 0
RCAL NO
MCTS NO
ALRM NO
BTT 30
ART 0
PECL NO
DCTI 0
TIDY 12345 1
SGRP 0
AACR NO

 

[SL1User]

And here for the BRI....


TYPE RDB
CUST 00
DMOD
ROUT 1
DES S0-EURO
TKTP DID
NPID_TBL_NUM 0
SAT NO
RCLS EXT
DTRK YES
DGTP BRI
IFC EURO
CNTY GER
CLID OPT1
PROG NCHG
SBN NO
SIDE USR
CNEG YES
OVLR YES
DIDD 5
OVLS YES
OVLT 0
MBGA NO
PGPN 1
RCAP COLP CCBS
INC_T306 0
OUT_T306 20
ISDN YES
MODE PRA
PNI 00000
NCNA NO
NCRD NO
CHTY BCH
CPFXS YES
SDID NO
DAPC YES
TBL 1
INTC NO
DSEL VOD
PTYP DCO
AUTO NO
DNIS NO
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD 1234
TCPP NO
TARG 08
BILN NO
OABS
INST
IDC YES
DCNO 1
NDNO 1 *
DEXT NO
DNAM NO
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GTO 896
GTI 896
SFB 3
IENB 5
TFD 0
SST 5 0
DTD NO
SCDT NO
2 DT NO
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DDO NO
DRNG NO
CDR YES
INC YES
LAST YES
QREC NO
OAL YES
AIA NO
OAN YES
OPA YES
OPD YES
NDP EXC 0
CDRX NO
CCO NO
NATL YES
SSL
CFWR NO
IDOP NO
MUS NO
MR DURC
DSPD NO
PANS YES
RUCS 12
RURC 12 0
RUCF 1 0
MULT NO
DSPT 10
MANO NO
EQAR NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
OHQ NO
OHQT 00
TTBL 0
ATAN NO
OHTD NO
PLEV 2
OPR NO
PRDL NO
EOS NO
DNSZ 0
RCAL NO
MCTS NO
ALRM NO
BTT 30
ACKW NO
ART 0
PECL NO
DCTI 0
TIDY 1234 1
SGRP 0
AACR NO


TN 2 0 0 0
APPL BRIE
ISDN_MCNT 300
CUST 0
CTYP SILC
MISP 1
MODE TE
MTFM NO
TKTP DID
CLOK YES
TSET 0
PDCA 1
ROUT 1
T302 15
T310 120
B1
MEMB 1
NITE
TGAR 0
NCOS 0
CLS UNR APN
B2
MEMB 2
NITE
TGAR 0
NCOS 0
CLS UNR APN
DATE 19 OCT 2001

 

[SL1User]

If the problem is, that it takes to long time to proceed call (until NIT = 8 sec expires) you may put FLEN in the SPNs to 0 and OVLT in DCH to 1.

 

[bpg1]

hi sl1user

thank you, just a few more ?

the prompt DAPC=yes what are TBL=1 and you have in rdb didd = 2 in isdn 30 route what are the number of digits of ext number?

in isdn 2 didd = 5 what are the number of digits of ext. number there?

 

[SL1User]

The didd deletes the two digits of the did number that telecom sends. For example the german number 069 aerea code for Frankfurt/Main the DID number 6697 and extension 1234.

In this case your DIDD prompt would be set to DIDD = 4 to delete the 6697 which will be send by default from the german telecom (and you only need the extension).

 

[SL1User]

About the DAPC, this is to show the incomming number with the AC in front of the transmitted originator DN. So if you have a call in your callers list the entry automati´cally will be dial able.

Example for the rout print above:

TYPE FTR_DATA
CUST 00
TBL
**DAPC**PREFIX TABLE NO: 00 **
UNKN**INTL**NATL**ESPN**LOCL**ELOC**ECDP**
UNKN*
E164* 00 0
PRIV*
E163* 00 0
TELX*
X121*
NATL*

**DAPC**PREFIX TABLE NO: 01 **
UNKN**INTL**NATL**ESPN**LOCL**ELOC**ECDP**
UNKN*
E164* 000 00
PRIV*
E163* 000 00
TELX*
X121*
NATL*

The programming is done in the FEATURE part of the CDB. Table 0 is default an not changeable.

 

[bpg1]

hi sl1user

just one problem back look at this print out it is a call from a local user inside the same city.
first trace is me testing from the pbx calling out and in again from isdn30 to isdn2 trying to simulat local call and that is ok.
last trace with time stamp 15:53:20 on dsl 1-0-0-0 is from local user in cuxhafen and as you se the last digit is missing, what is wrong??





~80****~L
TRA000
.
DSL 1 0 0 3 UIPE_OMSG CC_SETUP_REQ REF 00000078 CH 1 TOD 15:52:40 CK D86F5DA2

PROGRESS: ORIGINATING END IS NOT ISDN
PROGRESS: ORIGINATING END IS NOT ISDN
CALLING #:4588135000 NUM PLAN: E164 TON: UNKNOWN
CALLED #:3980130 NUM PLAN: E164 TON: UNKNOWN

DSL 1 0 0 3 UIPE_IMSG CC_SETUP_IND REF 0000001D CH 2 TOD 15:52:42 CK D86F6720

PROGRESS: ORIGINATING END IS NOT ISDN
PROGRESS: ORIGINATING END IS NOT ISDN
CALLING #:4721398010 NUM PLAN: E164 TON: NATL
CALLED #:3980130 NUM PLAN: E164 TON: LOCL

DSL 1 0 0 3 UIPE_OMSG CC_MORE_INFO_REQ REF 0000801D CH 2 TOD 15:52:42 CK D86F6
72F

DSL 1 0 0 3 UIPE_OMSG CC_PROCEED_REQ REF 0000801D CH 2 TOD 15:52:42 CK D86F674
8

DSL 1 0 0 3 UIPE_OMSG CC_ALERT_REQ REF 0000801D CH 2 TOD 15:52:42 CK D86F6753

PROGRESS: TERMINATING END IS NOT ISDN

DSL 1 0 0 3 UIPE_IMSG CC_MORE_INFO_IND REF 00000078 CH 1 TOD 15:52:42 CK D86F6
7D1

DSL 1 0 0 3 UIPE_OMSG CC_INFO_REQ REF 00000078 CH 1 TOD 15:52:42 CK D86F67DD


DSL 1 0 0 3 UIPE_IMSG CC_PROCEED_IND REF 00000078 CH 1 TOD 15:52:42 CK D86F692
0

DSL 1 0 0 3 UIPE_IMSG CC_ALERT_IND REF 00000078 CH 1 TOD 15:52:42 CK D86F6CC8

PROGRESS: INBAND INFO OR PATTERN IS AVAIL
PROGRESS: TERMINATING END IS NOT ISDN

DSL 1 0 0 3 UIPE_OMSG CC_SETUP_RESP REF 0000801D CH 2 TOD 15:52:50 CK D86FA7E
3
PROGRESS: TERMINATING END IS NOT ISDN

DSL 1 0 0 3 UIPE_IMSG CC_SETUPCOMP_IND REF 0000001D CH 2 TOD 15:52:50 CK D86FA
94A

DSL 1 0 0 3 UIPE_IMSG CC_SETUP_CONF REF 00000078 CH 1 TOD 15:52:50 CK D86FAA4
B
PROGRESS: TERMINATING END IS NOT ISDN

DSL 1 0 0 3 UIPE_IMSG CC_FAC_IND REF 00000078 CH 1 TOD 15:52:50 CK D86FAAD7
trak 1 3

ACTIVE DSL 001 0 00 03 B1

ORIG DSL 002 02 B2DID RMBR 0 2 INCOMING TRUNK CALL
TERM DSL 001 0 00 03 B2DID RMBR 1 8 OUTGOING TRUNK CALL
DIAL DN 86333980130
MAIN_PM ESTD
TALKSLOT ORIG 20 TERM 20
EES_DATA:
NONE
QUEU NONE
CALL ID 0 1327


---- ISDN BRIT CALL (ORIG) ----
CALL REF # = 5632
BEARER CAP = VOICE
HLC =
CALL STATE = 10 ACTIVE
CALLING NO = 4588135000 NUM_PLAN:E164 TON:INTERNATIONAL ESN:UNKNOWN
CALLED NO = 796098 NUM_PLAN:E164 TON:SUBSCRIBER ESN:NXX
---- ISDN BRIT CALL (TERM) ----
CALL REF # = 120
BEARER CAP = VOICE
HLC =
CALL STATE = 10 ACTIVE
CALLING NO = 4588135000 NUM_PLAN:E164 TON:UNKNOWN ESN:UNKNOWN
CALLED NO = 3980130 NUM_PLAN:E164 TON:UNKNOWN ESN:UNKNOWN

ACTIVE DSL 001 0 00 03 B2

ORIG DSL 001 0 00 03 B2DID RMBR 1 7 INCOMING TRUNK CALL
TERM DSL 008 0 00 12 B2MARP CUST 0 DN 6130 L500
DIAL DN 6130
MAIN_PM ESTD
TALKSLOT ORIG 11 TERM 11
EES_DATA:
NONE
QUEU NONE
CALL ID 0 1316


---- ISDN BRIT CALL (ORIG) ----
CALL REF # = 29
BEARER CAP = VOICE
HLC =
CALL STATE = 10 ACTIVE
CALLING NO = 4721398010 NUM_PLAN:E164 TON:NATIONAL ESN:NPA
CALLED NO = 3980130 NUM_PLAN:E164 TON:SUBSCRIBER ESN:NXX



.
DSL 1 0 0 0 UIPE_IMSG CC_SETUP_IND REF 00000014 CH 1 TOD 15:53:20 CK D8709809

PROGRESS: ORIGINATING END IS NOT ISDN
CALLING #:4721748242 NUM PLAN: E164 TON: NATL
CALLED #:398013 NUM PLAN: E164 TON: LOCL

DSL 1 0 0 0 UIPE_OMSG CC_MORE_INFO_REQ REF 00008014 CH 1 TOD 15:53:20 CK D8709
817

DSL 1 0 0 0 UIPE_IMSG CC_INFO_IND REF 00000014 CH 1 TOD 15:53:26 CK D870C292


DSL 1 0 0 0 UIPE_OMSG CC_DISC_REQ REF 00008014 CH 1 TOD 15:53:26 CK D870C2AA

CAUSE: #1 - UNASSIGNED NUMBER

DSL 1 0 0 0 UIPE_IMSG CC_RELEASE_IND REF 00000014 CH 1 TOD 15:53:26 CK D870C42
9

DSL 1 0 0 0 UIPE_OMSG CC_RELEASE_RESP REF 00008014 CH 1 TOD 15:53:26 CK D870C

 

[SL1User]

Who is the originator of the second call? Is it one of your test sets? For me it seems that the last digit simply was not dialed, and therefore the system answers with unasigned number. Which is ok because 13 is not existing 130 is.

Maybe you can give me a little more info about the second call.

 

[bpg1]

hi sl1user

second call is from cux port i think it is a part of cuxhafen, so it is from outside the pbx but internal in the city and i would say the same as you about not dial the last digits but they say they do. same problem as in the start of this tread about maybe co is sending the last digit later and i never see it?

 

[SL1User]

Do you or do they have the chance to trace their interface, maybe somethings wrong on their end.

Is the far end also a meridian?