how do u set up the console to receive the SDMR i know you have to go into for 34 but then what?! it says enter the extention. our console is 500 so i enter 500 and says its not vaild. dont' you have to do something in for 11 or 12 the data circuits or something liek that?
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
setting up SDMR
- Thread starter Matt85
- Start date
- Thread starter
- #3
- Thread starter
- #6
yea i don't know how to do any of that. i have the e-docs that came with on the disk for ver 1.1 orwhatever but i'm an end user i don't have the tech docs and my dealer doesn't know how to do a damn thing i ask him i always do it myself.
- Thread starter
- #7
here are the options to the dataset 1103 that doesn't work right. someone look at them and tell me if something is wrong please?
[ DESCRIPTOR NUMBER : 1 ] PARAMETER NAME VALUE
Session Inactivity Disconnect Timer 0 - 255 minutes 0
Guard Timer 0 - 99 seconds 2
Minimum Baud Rate 4800
Default Baud Rate 4800
Maximum Baud Rate 4800
Always Use Default Baud Rate When Called YES
DTR Off Disconnect Timer 0 - 99 seconds 5
DTR To CTS Delay Timer 0 - 9900 msec ( 100 msec inc ) 100
DTR Forced High YES
RTS Forced High YES
DSR Is Held High When Device Is Idle YES
CTS Is Held High When Device Is Idle YES
Originate A DTRX Call With A Low->High Transition of DTR NO
Action Taken If The Idle DTE Has DTR Low ( Auto Answer ) REFUSE
Pooled Modem Communication Established Indicator DCD
First Modem Tone ( 2025 Hz, 2100 Hz, 2225 Hz ) 2025 Hz
Second Modem Tone ( 2025 Hz, 2100 Hz, 2225 Hz ) 2225 Hz
ASYNC: Keyboard Origination Allowed ( Auto Baud ) YES
ASYNC: ADL Auto Baud NO
ASYNC: Flow Control XON/OFF <
ASYNC: XON Character ( 0 - 127, decimal value of ASCII code ) 17
ASYNC: XOFF Character ( 0 - 127, decimal value of ASCII code ) 19
ASYNC: Break Key Function SYS ATT
ASYNC: PBX Attention Character ( 0 - 127 ) 4
ASYNC: Parity NONE
ASYNC: Character Length ( 7 - 8 ; 8 bits implies no parity ) 8
ASYNC: Number of Stop Bits ( 1 - 2 ) 1
ASYNC: Autobaud To Host Character 1 ( 0 - 127 ) 13
ASYNC: Autobaud To Host Character 2 ( 0 - 127 ) 0
ASYNC: Delay Between Autobaud Characters 0-1270 msec (10msec inc) 100
DS2100: Operating Mode ( ASYNC, SYNC ) ASYNC.
SYNC: Rate Adaptation Scheme ( MiNET, X.31 ) MiNET
SYNC: Clock Source ( INTERNAL, SYSTEM, TX EXT, TX & RX EXT ) INTERNAL <
[ DESCRIPTOR NUMBER : 1 ] PARAMETER NAME VALUE
Session Inactivity Disconnect Timer 0 - 255 minutes 0
Guard Timer 0 - 99 seconds 2
Minimum Baud Rate 4800
Default Baud Rate 4800
Maximum Baud Rate 4800
Always Use Default Baud Rate When Called YES
DTR Off Disconnect Timer 0 - 99 seconds 5
DTR To CTS Delay Timer 0 - 9900 msec ( 100 msec inc ) 100
DTR Forced High YES
RTS Forced High YES
DSR Is Held High When Device Is Idle YES
CTS Is Held High When Device Is Idle YES
Originate A DTRX Call With A Low->High Transition of DTR NO
Action Taken If The Idle DTE Has DTR Low ( Auto Answer ) REFUSE
Pooled Modem Communication Established Indicator DCD
First Modem Tone ( 2025 Hz, 2100 Hz, 2225 Hz ) 2025 Hz
Second Modem Tone ( 2025 Hz, 2100 Hz, 2225 Hz ) 2225 Hz
ASYNC: Keyboard Origination Allowed ( Auto Baud ) YES
ASYNC: ADL Auto Baud NO
ASYNC: Flow Control XON/OFF <
ASYNC: XON Character ( 0 - 127, decimal value of ASCII code ) 17
ASYNC: XOFF Character ( 0 - 127, decimal value of ASCII code ) 19
ASYNC: Break Key Function SYS ATT
ASYNC: PBX Attention Character ( 0 - 127 ) 4
ASYNC: Parity NONE
ASYNC: Character Length ( 7 - 8 ; 8 bits implies no parity ) 8
ASYNC: Number of Stop Bits ( 1 - 2 ) 1
ASYNC: Autobaud To Host Character 1 ( 0 - 127 ) 13
ASYNC: Autobaud To Host Character 2 ( 0 - 127 ) 0
ASYNC: Delay Between Autobaud Characters 0-1270 msec (10msec inc) 100
DS2100: Operating Mode ( ASYNC, SYNC ) ASYNC.
SYNC: Rate Adaptation Scheme ( MiNET, X.31 ) MiNET
SYNC: Clock Source ( INTERNAL, SYSTEM, TX EXT, TX & RX EXT ) INTERNAL <
- Thread starter
- #8
the above are the options in form 11 data circuit discriptor. this is the COS options
[COS:10 SMDR ] OPTION (DISPLAYING ENABLED ) STATUS OPTION NUM
Attendant-Timed Recall (NO ANS) 0=disable 5-240 s 30 115 <
Attendant-Timed Recall (HOLD) 10-240 seconds 30 116
Attendant-Timed Recall (CAMPON) 0=disable 5-240 s 30 117
Attendant Call Forward No Answer Timer 10-240 s 30 118
Apply Key Line Conference Warning Tone ENABLED 126
Data Security ENABLED 216
Override Security ENABLED 238
Line Privacy ENABLED 240
Call Forward - Don't Answer Timer 2-6 rings 3 253
PBX Telephone - Call Hold Recall Timer 1-10 min 1 254
Repeated Camp-On Beeps Timer 5-15 seconds 10 255
UCD Music On Hold Timer 0-50 minutes 0 256
Display Prime As Forwarder ENABLED 258
Delay Ring Timer 2-6 rings 3 263
Paging Default (0-9) (0 Gives All Enabled Zones) 0 312
Recording Failure to Hangup Timer 1-255 seconds 30 404
Allow To Be Monitored <0=dis, 1=no beep, 2=beeps> 0 406
ONS Positive Disconnect <0 - 5 sec> <0 = disable> 0 506
Station/Set: Allow My Number to be Displayed ENABLED 507
> Telephone - Guest Room Template (0-3) 0 610 <
Alarm Audio Level for Sets RINGER 618
Telephone - Max Call Logs Allowed (0-20) 0 620
ACD - Agent Template (0-3, 0=disable) 0 650
ACD - Supervisor Template (0-3, 0=disable) 0 651
ACD - Senior Supervisor Template (0-3, 0=disable) 0 652
SMDR - Drop Calls < n Digits ( 0..11, disable=0 ) 0 803
Delay ONS Ring - Wait for Network Name ( 0-6 s ) 0 813
> DTRX Herald Text Select ( 1-4 ) 1 905 <
[COS:10 SMDR ] OPTION (DISPLAYING ENABLED ) STATUS OPTION NUM
Attendant-Timed Recall (NO ANS) 0=disable 5-240 s 30 115 <
Attendant-Timed Recall (HOLD) 10-240 seconds 30 116
Attendant-Timed Recall (CAMPON) 0=disable 5-240 s 30 117
Attendant Call Forward No Answer Timer 10-240 s 30 118
Apply Key Line Conference Warning Tone ENABLED 126
Data Security ENABLED 216
Override Security ENABLED 238
Line Privacy ENABLED 240
Call Forward - Don't Answer Timer 2-6 rings 3 253
PBX Telephone - Call Hold Recall Timer 1-10 min 1 254
Repeated Camp-On Beeps Timer 5-15 seconds 10 255
UCD Music On Hold Timer 0-50 minutes 0 256
Display Prime As Forwarder ENABLED 258
Delay Ring Timer 2-6 rings 3 263
Paging Default (0-9) (0 Gives All Enabled Zones) 0 312
Recording Failure to Hangup Timer 1-255 seconds 30 404
Allow To Be Monitored <0=dis, 1=no beep, 2=beeps> 0 406
ONS Positive Disconnect <0 - 5 sec> <0 = disable> 0 506
Station/Set: Allow My Number to be Displayed ENABLED 507
> Telephone - Guest Room Template (0-3) 0 610 <
Alarm Audio Level for Sets RINGER 618
Telephone - Max Call Logs Allowed (0-20) 0 620
ACD - Agent Template (0-3, 0=disable) 0 650
ACD - Supervisor Template (0-3, 0=disable) 0 651
ACD - Senior Supervisor Template (0-3, 0=disable) 0 652
SMDR - Drop Calls < n Digits ( 0..11, disable=0 ) 0 803
Delay ONS Ring - Wait for Network Name ( 0-6 s ) 0 813
> DTRX Herald Text Select ( 1-4 ) 1 905 <
- Thread starter
- #11
- Thread starter
- #12
I was trying to get your web site from you to get a phone number to speak to you because they frown on posting e mail
and phone numbers here and I would not dial in with out talking to you so or I could have walked you thru the process if you could tell me what you saw on the screen I guesss you are sol now I would have got this working for you the other night if you had replied like i asked CYA
and phone numbers here and I would not dial in with out talking to you so or I could have walked you thru the process if you could tell me what you saw on the screen I guesss you are sol now I would have got this working for you the other night if you had replied like i asked CYA
- Thread starter
- #14
oh ok i see what your saying. my extention is 759. leave a message if you can't get to me.
- Thread starter
- #15
I tried to call you today and you were't there
I am going to guess at this your console has a power
supply pluged into it if it has the plug for a wall wart find it and plug it in.and I am only guessing at this because i don't have any ICP MX's out there but this is how the data set in the console works on the el. go to to 12 and find the the bay slot and circuit for the console
for the type enter dscons you more than likely can use data
descriptor 1 . go to directed IO 34 and tell the dscons
to auto print smdr(remove the entry for smdr from the ds1103) I am not connected but if you know
the screens you get the general idea hook up your
laptop to the console port match your hyper terminal
to your descriptor 1 like 4800,N 8 1 no flow control
who knows the MX may not support the dscons and this info is useless but give it a try!!
I am going to guess at this your console has a power
supply pluged into it if it has the plug for a wall wart find it and plug it in.and I am only guessing at this because i don't have any ICP MX's out there but this is how the data set in the console works on the el. go to to 12 and find the the bay slot and circuit for the console
for the type enter dscons you more than likely can use data
descriptor 1 . go to directed IO 34 and tell the dscons
to auto print smdr(remove the entry for smdr from the ds1103) I am not connected but if you know
the screens you get the general idea hook up your
laptop to the console port match your hyper terminal
to your descriptor 1 like 4800,N 8 1 no flow control
who knows the MX may not support the dscons and this info is useless but give it a try!!
- Thread starter
- #18
- Status
Similar threads
- Locked
- Question
- Locked
- Question
- Locked
- Question