prtdiag CPU 1.0

[rgc41]

Hello, I'v got this error, the /var/opt/SUNWssp/adm/be-rm01/messages does not exists, how can I verify wat happened?
the prtdiag -v option gives me the same output.

************************************************
$ prtdiag
System Configuration: Sun Microsystems sun4u SUNW,Ultra-Enterprise-10000
System clock frequency: 100 MHz
Memory size: 20480 Megabytes

========================= CPUs =========================

Run Ecache CPU CPU
Brd CPU Module MHz MB Impl. Mask
--- --- ------- ----- ------ ------ ----
2 8 0 400 8.0 US-II 10.0
2 9 1 400 8.0 US-II 10.0
2 10 2 400 8.0 US-II 10.0
2 11 3 400 8.0 US-II 10.0
7 28 0 400 8.0 US-II 10.0
7 29 1 400 8.0 US-II 10.0
7 30 2 400 8.0 US-II 10.0
7 31 3 400 8.0 US-II 10.0
8 32 0 400 8.0 US-II 10.0
8 33 1 400 8.0 US-II 10.0
8 34 2 400 8.0 US-II 10.0
8 35 3 400 8.0 US-II 10.0
13 52 0 400 8.0 US-II 1.0 <-- error ??
13 53 1 400 8.0 US-II 10.0
13 54 2 400 8.0 US-II 10.0
13 55 3 400 8.0 US-II 10.0
14 56 0 400 8.0 US-II 10.0
14 57 1 400 8.0 US-II 10.0
14 58 2 400 8.0 US-II 10.0
14 59 3 400 8.0 US-II 10.0


========================= Memory =========================

Memory Units: Size
0: MB 1: MB 2: MB 3: MB
----- ----- ----- -----
Board 2 1024 1024 1024 1024
Board 7 1024 1024 1024 1024
Board 8 1024 1024 1024 1024
Board13 1024 1024 1024 1024
Board14 1024 1024 1024 1024


========================= IO Cards =========================

Bus Freq
Brd Type MHz Slot Name Model
--- ---- ---- ---------- ---------------------------- --------------------
2 SBus 25 0 SUNW,qfe SUNW,sbus-qfe
2 SBus 25 0 SUNW,qfe SUNW,sbus-qfe
2 SBus 25 0 SUNW,qfe SUNW,sbus-qfe
2 SBus 25 0 SUNW,qfe SUNW,sbus-qfe
2 SBus 25 0 fcaw/sd (block) FCW
13 SBus 25 0 QLGC,isp/sd (block) QLGC,ISP1000U
13 SBus 25 0 SUNW,qfe SUNW,sbus-qfe
13 SBus 25 0 SUNW,qfe SUNW,sbus-qfe
13 SBus 25 0 SUNW,qfe SUNW,sbus-qfe
13 SBus 25 0 SUNW,qfe SUNW,sbus-qfe
13 SBus 25 1 fcaw/sd (block) FCW
13 SBus 25 1 fcaw/sd (block) FCW
14 SBus 25 0 QLGC,isp/sd (block) QLGC,ISP1000U
14 SBus 25 1 fcaw/sd (block) FCW

For diagnostic information,
see /var/opt/SUNWssp/adm/be-rm01/messages on the SSP.

 

[xkjdhdg]

CD to the path in the error and use mkdir and make diectory called messages. This is were all of the boot messages are store from boot-up.