Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
PRI Programming to CP100 1
- Thread starter maxse
- Start date
Just program the CP to answer lines 001-023 or 031-053 depending on which slot the digital trunk card is in.
Brian Cox
Oregon Phone
Brian Cox
Oregon Phone
- Thread starter
- #3
Thanks Brian, on the other hand I am thinking this may be a problem because of a cp100 (4channels).
Basically I have 3 separate businesses using 4 analog trunks each...now converting to a pri 12 channel.
From what I understand I would program the calls going to each business DID through logical lines 145+.
Would I just leave the lines 001-023 alone and not assign them to anything if all my calls are coming through DID's?
Basically I have 3 separate businesses using 4 analog trunks each...now converting to a pri 12 channel.
From what I understand I would program the calls going to each business DID through logical lines 145+.
Would I just leave the lines 001-023 alone and not assign them to anything if all my calls are coming through DID's?
Yes. Just program the AA to answer the target lines 145 and up as needed. For private DID's set the AA to no answer and forward/no answer the target line owner to the CallPilot DN.
Brian Cox
Oregon Phone
Brian Cox
Oregon Phone
Note that on later release software the target lines start at 157.
Brian Cox
Oregon Phone
Brian Cox
Oregon Phone
The listed billing number needs to be assigned to a target line and that target line needs to be assigned to the AA...the lines for the PRI don't matter
"If I had known it would turn out like this, I would have became a locksmith" Albert Einstein
NCSS NCTS NCTE CS1000E
Mitel 3300 4.2 basic & advanced, 5000 4.0, NuPoint I&M 4.2
"If I had known it would turn out like this, I would have became a locksmith" Albert Einstein
NCSS NCTS NCTE CS1000E
Mitel 3300 4.2 basic & advanced, 5000 4.0, NuPoint I&M 4.2
Are you sure it is a PRI or T1?? If you have a fractional PRI, you don't have all channels available to you. You are only using 12 out of the 23. So you say. As far as your 3 businesses, if they had 4 lines programmed to appear and ring you are going to have to assign target lines to each one. If the digits are still the same, each business ext. will need 4 target lines assigned to duplicate your previous setup.
As for the aa you need only to assign your target line 145 or 157 ( depending on software )with the last 4 digits of the billing number to be answered. As Crow says lines for the PRI don't matter.
Do these businesses also have aa after hours????
Voice Connect Plus, Inc.
have a great day and a better tomorrow
As for the aa you need only to assign your target line 145 or 157 ( depending on software )with the last 4 digits of the billing number to be answered. As Crow says lines for the PRI don't matter.
Do these businesses also have aa after hours????
Voice Connect Plus, Inc.
have a great day and a better tomorrow
- Thread starter
- #8
- Thread starter
- #9
curlycord
Programmer
We don't assign lines to AA as it appears they are saying (therefore multiple appearances not required either), instead we tell AA to answer desired lines.
If company A is Target line 157 then go into Voice Mail AA/Lines and have Line 157 answered and select your desired ring count.
Do same for each business...i.e. company B might be 158 and c 158 and so on.
=----(((((((((()----=
curlycord
If company A is Target line 157 then go into Voice Mail AA/Lines and have Line 157 answered and select your desired ring count.
Do same for each business...i.e. company B might be 158 and c 158 and so on.
=----(((((((((()----=
curlycord
- Thread starter
- #11
Company A
Line 001 - Main
Line 002 - hunt
Line 003 - hunt
Company B
Line 004 - Main
Line 031 - hunt
Line 032 - hunt
Company A
Line 157 - Main & Assign Multiple Line Appearances
Company B
Line 158 - Main & Assign Multiple Line Appearances
Does that look about right??
Line 001 - Main
Line 002 - hunt
Line 003 - hunt
Company B
Line 004 - Main
Line 031 - hunt
Line 032 - hunt
Company A
Line 157 - Main & Assign Multiple Line Appearances
Company B
Line 158 - Main & Assign Multiple Line Appearances
Does that look about right??
- Thread starter
- #12
curlycord
Programmer
Assign Multiple Appearances to what?
I thought you wanted AA to answer?
=----(((((((((()----=
curlycord
I thought you wanted AA to answer?
=----(((((((((()----=
curlycord
- Thread starter
- #14
Yeah, the multiple appearances are necessary for the attendant (or whoever is prime for the target line) to receive more than one call
"If I had known it would turn out like this, I would have became a locksmith" Albert Einstein
NCSS NCTS NCTE CS1000E
Mitel 3300 4.2 basic & advanced, 5000 4.0, NuPoint I&M 4.2
"If I had known it would turn out like this, I would have became a locksmith" Albert Einstein
NCSS NCTS NCTE CS1000E
Mitel 3300 4.2 basic & advanced, 5000 4.0, NuPoint I&M 4.2
curlycord
Programmer
But he wants AA to answer....sounds like we are confusing him to assign lines and multiple appearances when we don't need to do in this case?.
=----(((((((((()----=
curlycord
=----(((((((((()----=
curlycord
- Thread starter
- #17
No, I understand that I will need to assign the target line to the AA just like I would assign the analog trunk (line) to the AA currently. My main concern is programming multiple line appearances now that I have realized how to program the AA.
-
1
- #18
curlycord
Programmer
That's what I am saying, you do not assign lines to AA or voice mail.....leave that for sets only!!!!!.
Multiple appearances only needed for a set and not vmail.
If AA is to answer:
Go into AA and tell the line if it is to be answered yes or no.
If a set is to answer:
Go to Lines and assign a Target Line to a set, once you make it A&R or Ring Only keep pressing SHOW when you do and assign 2 or 3 appearances.
Do same for other targets/companies.
=----(((((((((()----=
curlycord
Multiple appearances only needed for a set and not vmail.
If AA is to answer:
Go into AA and tell the line if it is to be answered yes or no.
If a set is to answer:
Go to Lines and assign a Target Line to a set, once you make it A&R or Ring Only keep pressing SHOW when you do and assign 2 or 3 appearances.
Do same for other targets/companies.
=----(((((((((()----=
curlycord
You're right curlycord, I didn't read where he was wanting AA to answer and therefore my answer would have muddied the waters.
"If I had known it would turn out like this, I would have became a locksmith" Albert Einstein
NCSS NCTS NCTE CS1000E
Mitel 3300 4.2 basic & advanced, 5000 4.0, NuPoint I&M 4.2
"If I had known it would turn out like this, I would have became a locksmith" Albert Einstein
NCSS NCTS NCTE CS1000E
Mitel 3300 4.2 basic & advanced, 5000 4.0, NuPoint I&M 4.2
- Status
Similar threads
- Locked
- Question
- Locked
- Question