Overhead paging with Bogen 2

[AnthonyHardy]

Hey guys, I need some help. I've got an opt 11c that I need to get overpaging functional on. I've got a Bogen 24V ps and horn to test with before we purchase all of our equipment.

My Nortel experience is limited to MACs for the most part, but I can follow instructions easily and have documentation, but need a push in the right direction.

The ps calls for tip and ring loop start. I have an empty trunk port to use. I've searched the forums and thought I should setup a route, and a PAG trunk. So I've done that and can dial the ACOD and get dead air, but nothing over the horn. WHen the horn is hooked into the trunk, it's muted, like I believe it should be. WHen i pull the connection, there is static (again, like I would think it should work), but I honestly don't know what I'm doing.

Any words of wisdom? I can post the rdb and trunk if that would help, but I think I'm just on the wrong track somehow.

 

[Reusser]

From trunk port to Bogan amp is just an analog signal - best way to test to determine connections to Bogen is connect your toner to Bogen ports. Once you get it right you will hear your toner over speaker.

Then connect your pag trunk port.

 

[EddieDuece]

Here is how my trunk and route is built, just so you can compare to ensure it is built correctly.

DES PAGING
TN 012 0 01 05
TYPE COT
CDEN 8D
CUST 0
XTRK EXUT
FWTM NO
TIMP 600
BIMP 3COM
AUTO_BIMP NO
TRK ANLG
NCOS 0
RTMB 5 1
NITE
SIGL LOP
SUPN NO
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD
P10 NTC
TKID
AACR NO
DATE NO DATE
************************************************************
TYPE RDB
CUST 00
ROUT 5
DES PAGING
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
ICOG OGT
RANX NO
SRCH LIN
STEP
ACOD 74
CPP NO
TARG 01 02 04 06
CLEN 1
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
OOD 1
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512

IENB 5
TFD 0
LEXT 100
VGD 6
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
CDR NO
MUS NO
MR NO
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0


PAGE 002

FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

 

[AnthonyHardy]

Thanks guys! I've almost got it now. I have a functional paging port that can be dialed from phones with a tgar of 0. Two more things and I promise I'll leave you guys alone for a while.

1. How can I edit a route to change the ACOD? I can't find anything on this on the web or here.
2. Editing it would allow me to alter the TARG as well.

I'm still looking, but I haven't found it yet.

Thanks again!

 

[AnthonyHardy]

never mind. ld 16.

 

[Reusser]

find an unused number

LD 20
Req: prt
Type: LUDN

change Route
ld 16
req: Chg
Type: RDB
Rout: 5
<cr> until you get prompt ACOD Enter new value
<cr> until you get prompt TARG enter x and value to remove, if you remove all enter 0 also

<cr> rest of way

 

[AnthonyHardy]

Perfect Reusser. I found ld16, but didn't know the x remove piece. Thanks!

 

[AnthonyHardy]

Drat! One final glitch and this is setup.

When the console is in day mode, the operator can transfer me to the correct extension. When the console is in night mode it goes to an automated menu (callpilot handles that I think), but you aren't allowed to dial the extension. Any ideas?

 

[AnthonyHardy]

Here is what is happening. We get our standard night menu, I dial the ACOD and get one ring and then "Your connection cannot be completed at this time.

 

[Reusser]

Probaly needs to be added to restriction / permission list in call pilot