Out going CLIP of ipldk 1

[Jonah29]

Hi all,
Providing the line provider has clip enabled. Is there a way to send a number other than the main number or users ddi number? I know as default the system will send he main number and I can also programme the clip of the individual extension and send this to line but is there a table where I can choose the number to be sent. The scenario would be a ddi rings a hunt group of say 4 phones, now when any of those 4 phones make an outgoing call, the ddi number for the hunt group is sent and displayed rather than the main number or any of the individual ddi numbers. I was able to do this on Panasonic TD and TDA I was just wondering if such a feature was available on the LG ipldk and perhaps even the ipecs/ ucp.
Regards
Mark

 

[eats4treats]

Hi Jonah29

I have found using options 1 or 3 below to get the results you need. If option 1 doesn't work then use 3 before doing 2. Never really had to use option 2 or 4 before.

Sending CLI on the LDK – Option 1
Program DDIs as per normal - PGM 231 - Flex DDI, PGM 140 FK 1- Line Type DDI, PGM 143 FK 4 - Conversion Type 2.
PGM 114 FK 5 - Out Going CLI or COLP - Set as EXT (default)
PGM 114 FK 12 - Logical STA Number CLI - number to be sent. E.g. If extn 102 is to send 802 type in 802.
PGM 114 FK 14 - CLIR – OFF (default)
PGM 114 FK 15 - COLR – OFF (default)
PGM 143 FK 2 - CLIP Table Index - set as 01
PGM 143 FK 3 - Call Type - NATIONAL
PGM 201 - COLP Table. Enter The first three digits of the tele number. e.g. 259

01444 259 802
From Network In COLP Table Logical STA Number


Sending CLI on the LDK – Option 2
Program DDIs as per normal - PGM 231 - Flex DDI, PGM 140 FK 1- Line Type DDI, PGM 143 FK 4 - Conversion Type 2.
PGM 114 FK 5 - Out Going CLI or COLP - Set as EXT (default)
PGM 114 FK 8 – CPN Type – Set as 1
PGM 114 FK 12 - Logical STA Number CLI - number to be sent. E.g. If extn 102 is to send 802 type in 802.
PGM 114 FK 14 - CLIR – OFF (default)
PGM 114 FK 15 - COLR – OFF (default)
PGM 143 FK 2 - CLIP Table Index - set as 50 (display will show pgm114 btn5)
PGM 143 FK 3 - Call Type – UKNOWN (default)

01444 259 802
From Network From Network Logical STA Number


Sending CLI on the LDK – Option 3 (2.2 Software and above)
Program DDIs as per normal - PGM 231 - Flex DDI, PGM 140 FK 1- Line Type DDI, PGM 143 FK 4 - Conversion Type 2.
PGM 143 FK 2 - CLIP Table Index - set as 50 (display will show pgm114 btn5)
PGM 114 FK 18 – CLI Type - set as Long
PGM 114 FK 19 – Long STA CLI – set to whatever you want to send to line

Sending CLI on the LDK – Option 4
Program DDIs as per normal - PGM 231 - Flex DDI, PGM 140 FK 1- Line Type DDI, PGM 143 FK 4 - Conversion Type 2.
PGM 114 FK 5 - Out Going CLI or COLP - Set as EXT (default)
PGM 114 FK 12 - Logical STA Number CLI - number to be sent. E.g. If extn 102 is to send 802 type in 802.
PGM 143 FK 2 - CLIP Table Index - set as 50 (display will show pgm114 btn5)
PGM 114 FK 8 – CPN Type – Set as 0 (default)
PGM 143 FK 3 - Call Type – UKNOWN (default)

In the event of having to start again to try a different option the Default settings on C.0Cc are as follows: -
PGM 114 FK 5 – EXT
PGM 114 FK 8 – 0
PGM 114 FK 12 – STA Number
PGM 114 FK 14 – OFF
PGM 114 FK 15 – OFF
PGM 114 FK 18 – Short
PGM 114 FK 19 – Blank
PGM 143 FK 2 – Not Assigned
PGM 143 FK 3 – Unknown



Ok, Press Trans *#..... TRANS/PGM..... the transfer key?.......sigh!

 

[Jonah29]

Thanks Eats,

I'll have a go

Mark