Option 61 to Cisco Gateway Programming

[SSgt]

Hello, working for 10 years on the 100's but I am trying to get a connection from an option 61 to Cisco gateway and an unbelievably lost, can anyone get me pointed in the right direction? Like what load creates trunks, LD 96 creates the D-channels and LD60 creates all the other channels right?

Thanks!

 

[TAnselm]

Wrong....
First create a route in LD 16
Create a T in LD 15
Build the channels in LD 14

 

[RS528]

I have build last month a connection between a nortel and Cisco. Here's the config.

Configure QSIG on Nortel for connection between Nortel en Cisco Callmanager.


Route


TYPE RDB
CUST 00
DMOD
ROUT 100
DES CISCO
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC ISGF
SBN NO
PNI 00000
NCNA NO
NCRD NO
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC YES
TBL 1
INTC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 7100
TCPP NO
TARG
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
SIGO STD
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DRNG NO
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
RACD NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 7100 100
SGRP 0
AACR NO

D-Channel

ADAN DCH 11
CTYP MSDL
CARD 01
PORT 1
DES Cisco
USR PRI
DCHL 1
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISGF
PINX_CUST 0
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
QCHID YES
RCAP COLP NDI CCBI CCNI PRI DV3I CTI QMWI
PR_TRIGS DIV 2 3
CNG 2 3
PR_RTN NO
MBGA NO
OVLR YES
DIDD 0
OVLS NO
T310 120
INC_T306 6
OUT_T306 6
T200 3
T203 10
N200 3
N201 260
K 7




TRUNK

DES CISCO
TN 001 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI2
PDCA 1
PCML A
NCOS 0
RTMB 100 1
B-CHANNEL SIGNALING
TGAR 0
AST NO
IAPG 0
CLS UNR DTN CND WTA LPR APN THFD XREP BARD
P10 VNL
TKID
DATE 8 FEB 2007


Note

The connection between the Nortel en Cisco must be crossed.
Pin 1 goes to 4, and pin 2 to 5.

The Cisco is Master the Nortel User.

On both sides CRC ON or OFF

 

[johnpoole]

here's the qsig a lot of us have used here. i used a standard patch cable between those two with red/green on the db-15 to pins 1 and 9 and orange blue to pins 3 and 11 of the rj.. that one works with the nortel being side net and the far end clocking off of it.. since that is the only pri on the ccm clocking via that would be the same as freerun.. my 81 clocks off of ld, the cisco clocks off of it.

http://www.tek-tips.com/viewthread.cfm?qid=1017219

john poole
bellsouth business
columbia,sc

 

[SSgt]

Thanks...I've finally got the setup in the SL-1 correct, I think yet I'm not getting a carrier, I am using the standard configs just want to verify that the callmanager settings you used are: So I know if I should be looking at a wiring problem.

PRI Protocol NI2
Network
B8ZS
ESF

Thanks again!

 

[johnpoole]

i perfer to clock the cisco off of the nortel.. then clock the nortel off of the ld.. i don't use cisco as a clock source due to network kids and there love of a power cycle.. the nortel will tell you if the trouble is layer one.. if you have a red alarm then you don't have copper. if you have yellow, copper is good and nortel thinks the trouble is on the far end.. after the build (or any change) dis msdl x all then enl msdl x fdl to write that change to the card.. (ld 96) ld 60 stat for trouble, lcnt for clocking errors, (slips bi-polar etx)

john poole
bellsouth business
columbia,sc