Option 11C SYS000 000809

[CanGoalie]

Good morning,

Running an Option 11C at Rls 25.40B

The unit performed a SYSLOAD and I am trying to determine the cause. Have not seen 000809 in posts before.
The switch also did not come up clean as I had to get two TMDI cards hard reset in order to be able to send enable commands to them The system was saying they were not present.

Here is a print.

100%
SYS000 000809 000000 000000 000000 CPU 0
SYSDB RLS/ISS: 2540B LOADED FROM C: DATE/TIME: 16/2/2009 04:08:28 RECS: 59 SEQ
NO: 1431
SYSLOAD ISSUE 25.40B: IDLE_SET_DISPLAY ÎÏÒÔÅÌ
INI000 00000000 05 38 31 00000000 00000000 00000000 00000000 00000000
SRPT752 INI 0: INI completed in 13 seconds
DSET000 DOWN LOAD 214 0 18 0 0 0 0 103577
INI002 00000088 00000083 00000080

INI003 0000009C 000000A0 000000AF 000000B0 000000B4 000000B8 000000BC 000000CE
000000D0
INI003 000000D4 000000D8 000000EE 000000EF

XMI002 2 XMLC
XMI002 10 MMAIL
XMI002 4 XDLC
XMI002 5 XDLC
DTC105 0
DTC007 0
CSA001 9 5:39:32 16/02/2009 9

Any help appreciated.

Thanks

 

[johnpoole]

you need the codes prior to the sysload, not post.. in that old of a rls, tmdi needing a reseat was not uncommon... prior to rls 21 most problems could be fixed by an ini,, the 1st rls 21 i installed required reseating of most controller cards to get the ipe's up after any ini.. not a great improvement.. a new rls of cni cards helped around rls 23

john poole
bellsouth business
columbia,sc

 

[GHTROUT]

Unfortunately, a sysload clears the History file, leaving the SYS message as the start of the file.

If you can get into PDT, do an "rdall" a few times.

~~~
[small]GHTROUT.com | CS1000 Programming and Feature Guides | Tek-Tips FAQs | Recent Replies[/small]

 

[CanGoalie]

Thank you, I will try these prints in PDT.

 

[Tman45]

Do you happen to have backups running at 4:00am?? (DATE/TIME: 16/2/2009 04:08:28)
I have seen quite a few sysloads in my day around 'midnight routines'
I was gonna say look at the controller cards, but who knows really ... haha
Good luck in advance.
Last note: Did you have any maint/after hours work done recently?

INI002 I/O device fault, where xx is to the maintenance display code in.
Action:
Severity: Critical. Critical to Monitor: Yes. SNMP trap: Yes

INI 003 Network or PE signaling fault, where xx is the maintenance display code in
HEX.
Action:
Severity: Critical. Critical to Monitor: Yes. SNMP trap: Yes

 

[CanGoalie]

Just to update: The problem was really narrowed down when the power supply smoked in the switch. (11C) I was surprised since SYS809 did not seem to point to power.

Thanks for the replies

 

[telebub]

For some reason when you let the smoke out of the system it doesn't run too well. And you can't just put the smoke back in, you have to replace it with expensive factory smoke. B-)

War Eagle!
Lions Baseball '09!

 

[GHTROUT]

That is exactly why I never change the oil in my car...the factory oil is the best.

~~~
[small] [©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators [/small]