OPT 81c - TTY locked into overlay 20 4

[M1north]

I was doing some changes and I screwed up my key input to where I was typing:

Req: MOV
type: TNB

Well, I did this twice and now the TTY port will only repeat the above when I hit any buttons.

I cant logout or login. Other TTYs are wokring but it shows this TTY as in use on LD32

Here is my log:

REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG
TYPE:
TYPE TNB
SCH0111
REQ:
REQ CHG

INI time ??

 

[bigindian65]

go to ld 37 and dis tty xx

then, re-enable.

Mato' Was'aka

 

[PERRYPJ]

Try logining in another TTY and do a FORC X, X being the TTY number

OLD ROLMEN WORKING ON NORTELS AND AVAYA

 

[phonz1]

to FORC you have to login as level 2

 

[strmwalker]

HAVE YOU TRIED TO HOLD DOWN THE SHIFT KEY AND HIT THE
8 KEY TO FOUR STAR OUT?


no problems only solutions

strmwalker

 

[M1north]

Thanks for the replies. TTY issue. It auto logged me out after 5 min. When I try to login, everything I do translates to hitting the enter key on that tty only. All other TTy`s work fine

I tried to enl/dis but no resolve. I will re-seat the paddle board and that should fix.

Thx

 

[GHTROUT]

The terminal itself could be the problem.

If you can get to the caret prompt, type "LON" and see if that works - if not, type "LOF" (Line Mode On/Off)

But if you can't get to the caret prompt, just INI

GHTROUT.com | FAQs | Recent Replies

 

[CSkabul]

its a known issue from nortel Pls install the latest patches

 

[M1north]

Another strange twist. J25 on core 1 will not respond to direct connect with my laptop.

 

[M1north]

Can someone tell me the procedure to fix this J25 port?

I will guess:

1.Switch Cores and see if Core 0 works
2.Switch back and try Core 1 again
3.Ini active core?
4.Call vendor and pray its not the backplane or CPU?

 

[GHTROUT]

The procedure your gonna need is to INI. As that one poster said, I guess it is a known issue...which means it's not hardware.

GHTROUT.com | FAQs | Recent Replies

 

[M1north]

I`m sorry, but what is a known issue? The fact that a TTY port is not responding properly? This is not connected to a terminal. This is a tty used for modem dial-up.

I am assuming that this is a hardware issue with my paddle board and does not involve software patches to fix...

 

[GHTROUT]

You said you couldn't get into the core either.

GHTROUT.com | FAQs | Recent Replies

 

[M1north]

Yes, I cannot connect to core0 directly on J25. Is this a known issue that requires a patch? The above poster mentioned this before I mentioned the Core issue..

 

[GHTROUT]

I see all of that. Please let us know what finally does solve it. Paddle boards are notorious for faulure - odd stuff, like you have. You might just try moving (in h/w and s/w) the port to another position on the paddle board.

GHTROUT.com | FAQs | Recent Replies

 

[tnphoneman]

Oddly I have run into some switches where J25 and J21 were reversed.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.

 

[M1north]

I was just able to get back and look into this. Both CPU on Core0 + 1 J25 will not respond.

I know this was working before. Error on CP card is 87 SDI 07. I will try to re-seat the paddle board but it looks like ini time....

 

[M1north]

TO close this out:

INI on switch, ports came back up. tty 7 is working fine. Ordered a new xsdi card and will replace the old one.

Thx to all...