Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Octel 250 - Type of Printer To Use
- Thread starter Spirit1
- Start date
That depends on they type of terminal you have.
What kind are you using?
Ken Means
What kind are you using?
Ken Means
- Thread starter
- #3
any serial printer will work with that terminal if you had a Wyse 50+ you could also set it to use the parallel port for a printer. I do not think the HP has a port that can be used for a parole printer but I may be wrong as I have not used one in many years.
Ken Means
Ken Means
101–1386–001 Edition 2
SETTING UP PRINTERS
Overview
Octel Communications ships the Epson FX–870 printer with Overture 250 and 350
servers. Any of the following printers can also be used:
. Fujitsu DL1250
. Fujitsu DL1200
. Fujitsu DX2100 and DX2300
. Okidata ML320
. AT&T
. Mannesmann Tally MT290
Before setting up your printer, read the “Meeting Cable Requirements” section, page
3-2, to make sure that you have the correct serial-interface cable.
3
3-2 Peripheral Equipment
101–1386–001 Edition 2
Meeting Cable Requirements
You must have a serial interface cable that meets the following requirements:
. The cable at the printer end must have a 25-pin male connector, such as a Cannon
DB-25P or equivalent.
. The cable must be no more than 50 feet (15.2 m) long.
Refer to Table 3-1 for the correct cable.
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Table 3-1. Serial Interface Cable Requirements.
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
TerminalÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ Required
CableÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
HP 700/43
Wyse 55ES
DEC VT102 or
VT220ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
P/N 057–1149–000
P/N 058–1089–000
Refer to the DEC user’s manual
Setting Up the Printer
Setting up the printer requires four procedures:
. Unpacking the printer
. Connecting the printer to the SMT
. Checking the printer parameters
. Testing the printer
Refer to your printer and SMT manuals for the necessary procedures.
Ken Means
SETTING UP PRINTERS
Overview
Octel Communications ships the Epson FX–870 printer with Overture 250 and 350
servers. Any of the following printers can also be used:
. Fujitsu DL1250
. Fujitsu DL1200
. Fujitsu DX2100 and DX2300
. Okidata ML320
. AT&T
. Mannesmann Tally MT290
Before setting up your printer, read the “Meeting Cable Requirements” section, page
3-2, to make sure that you have the correct serial-interface cable.
3
3-2 Peripheral Equipment
101–1386–001 Edition 2
Meeting Cable Requirements
You must have a serial interface cable that meets the following requirements:
. The cable at the printer end must have a 25-pin male connector, such as a Cannon
DB-25P or equivalent.
. The cable must be no more than 50 feet (15.2 m) long.
Refer to Table 3-1 for the correct cable.
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Table 3-1. Serial Interface Cable Requirements.
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
TerminalÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ Required
CableÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
HP 700/43
Wyse 55ES
DEC VT102 or
VT220ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
P/N 057–1149–000
P/N 058–1089–000
Refer to the DEC user’s manual
Setting Up the Printer
Setting up the printer requires four procedures:
. Unpacking the printer
. Connecting the printer to the SMT
. Checking the printer parameters
. Testing the printer
Refer to your printer and SMT manuals for the necessary procedures.
Ken Means
Sorry for bringing up an old thread.....but is there any other configuration necessary? Or can I just plug a parallel printer into the proper port on the terminal and run the reports? Do I have to config the system software with the printer specs, or is it programmed into the terminal itself (like the AT&T 513 & 715 terminals on Avaya PBX's)?
Thanks in advance -
- Duaneness
Thanks in advance -
- Duaneness
You must config the terminal to use the parallel printer and that is it
Ken Means
Ken Means
does it have a parallel port on the back ? if it does you go into setup and select the printer type
Ken Means
Ken Means
Yes, there is a parallel port on the admin terminal, but there isn't a "setup" key on the keyboard. This keyboard looks just like a regular PC keyboard, except it has the small RJ- type connector on it which plugs into the terminal. I suppose I could play around with it and see what happens....
- Duaneness
- Duaneness
sounds like you have the wrong keyboard. i know there is a way to get into the setup and change it do you have the manual ?
Ken Means
Ken Means
go to this link it will show you how to get into the setup
Ken Means
Ken Means
- Status
Similar threads
- Locked
- Question