Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Norstar Conference phone

Status
Not open for further replies.
Jan 15, 2014
19
0
0
US
I have a used Norstar Polycom conference phone that is suppose to work as a direct connect.
We have a 0x32 Mics. Can someone please tell me how to configure? I have dial tone but get a fast busy anytime i try to make outbound call.
Any help is greatly appreciated
 
I'm assuming that your Polycom conference phone is an analogue model?. Is it connected via an ATA (Analogue Terminal Adapter)?.

Are you able to call internal extension phones OK?. If so, then have you programmed the extension port for outgoing line pool access and check that the set isn't also barred.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
Try dialing 9 before you dial the number.

Look under Sets/LineAccess for what Firebird describes.

If unsure how to program you need to call in a tech.
You can also read the Installer guide which has the info you need.

________________________________________

Add me to LinkedIN

small-logo-sig.png

=----(((((((((()----=
Toronto, CAN
 
It is a Norstar Polycom and suppose to run off Norstar port. I do not have an ATA.
I get dial tone but when i press 9for outbound call i get the fast busy. I've been using a 7310 at the same extension.
 
What is the item code on the "Norstar" Polycom please?. Have you confirmed in programming that "9" is assigned to the extension?.

Also when logging in via the Telset terminal, are you able to look into the Mntce section and access the extension / port status area to see that type the system sees in plugged in.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
What you have is called a Norstar Conference Unit and is made by Polycom for Nortel....no need for Firebirds above request.

Refer back to my original reply now except for the dial 9 bit.
You wont get training here if you do not know how to program.






________________________________________

Add me to LinkedIN

small-logo-sig.png

=----(((((((((()----=
Toronto, CAN
 
Yes, it is a Norstar Conferencing unit. 2501-03308-001. Extension is programmed to dial 9. I have2 i/c 's assigned, hf answerback at no, prime line is intecom.
Have dial tone but busy signal as soon as i hit 9. Can do some programming just unsure what am not doing.
 
If you get same result from a standard phone bi Intercom then 9 and a busy then the lines may not be in a Pool and are instead set to Public.
Go into Lines/Data and put all ONLY working lines into Pool A.

________________________________________

Add me to LinkedIN

small-logo-sig.png

=----(((((((((()----=
Toronto, CAN
 
I will try that but when i plug a 7316 into the port i have no problem making outbound call after hitting 9.
 
Plug T7316 in then go into programming, check System/FeatureSettings to see if Set Relocation is ON, if it is turn it OFF.
Now plug NCU back in and see if same issue.

________________________________________

Add me to LinkedIN

small-logo-sig.png

=----(((((((((()----=
Toronto, CAN
 
I don't think I've ever seen a
"Norstar Conferencing unit. 2501-03308-001" over this side of the pond. Was the phone also compatible on BCM systems?

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
**Norstar Audio Conferencing Unit I should have said.

Yes it is compatible on BCM.

There was one made for the Option/M1 as well.....did you get that over there?



________________________________________

Add me to LinkedIN

small-logo-sig.png

=----(((((((((()----=
Toronto, CAN
 
Yes Curly, I did fit one on a Option 11 system via a digital port many moons ago. I never knew that they also did one for the Norstar / BCM range.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
They have 2 models that are direct connect on the Norstar & BCM line.

The Nortel part #s are NTAB2666 for the older one and NTAB4213 for the newer looking one.

NTAB2666 looks like an older soundstation non display and the NTAB4213 like a soundstation2 non display.

NTAB2666 = 2501-03308-001

NTAB4213 = 2301-15100-001

 
Prime line is pool also for that extension?.or itcm and use 9
Jacktel
 
I have to assume that line pool access has not been allowed for the Polycom DN even though a Norstar digital phone is able to dial 9 and access an outside line. As curly wrote it has to be that set relocation is turned on. You can verify by dialing 0 from both the Polycom and a digital phone and ask the attendant what the station ID is on their display.

Brian Cox
Georgia Telephone
 
Good day.

I have confirmed that set relocation is off.
I can dial extensions with no problem but if i press 9, i am just getting the fast busy. In maintenance, shows as a m7100.
 
Then you need to allow access to Pool A if you have copper pots lines or PRI-A if you have PRI.

Old software - Configuration/LineAccess/LinePoolAccess
New software - Sets/LineAccess/LinePoolAccess


________________________________________

Add me to LinkedIN

small-logo-sig.png

=----(((((((((()----=
Toronto, CAN
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top