Need help programming router for frame relay

[rgomez1999]

Any help is greatly appreciated. I am in the process of setting up 15 Netvanta 3200 Routers for a frame relay connection between various sites. The manufacturer stated that programming the router is 95% the same as programming Cisco routers and that's why I'm posting my plea here. Listed below is the information that was provided to me by AT&T which is our ISP. We received a Cisco 3640 router in which they programmed for us and it works. All of our sites are suppose to communicate with my main site. We currently have 2 T-1's running into the Cisco Router. I changed the IP address for our own protection.

Link 1 (Serial 0/0) IP Address 10.126.230.154
Link 2 (Serial 0/1) IP Address 10.126.230.170
Link 3 (Serial 1/0) IP Address n/a
Link 4 (Serial 1/1) Ip Address n/a

Mask for Link 1 & 2 is 255.255.255.252

LAN IP Address Block: 10.2.56.0 thru 10.2.56.255
Mask for LAN IP Address Block: 255.255.255.0
Ethernet 0/0 and 1/0 Address: Not Being Used At This Time

Fast Ethernet 2/0 Address: 10.2.56.0

Primary DNS: 10.126.16.67
Secondary DNS: 10.126.17.71

They told me the gateway for our PC's would be 10.2.56.1

Listed below is the config tool software layout that allows me to generate a script file for the routers. To note, each of our sites are going to be allocated a certain number of IP Addresses. (i.e. Site 1, 10 IP's, Site 2, 60 IP's, etc..) Each site is also going to have a certain number of bandwith allocated to them 256k, 128k, 512k, etc.) I also received the DLCI numbers for the sites they completed installing the smart jacks at. Here's the tool that I need help in trying to generate a script.: (BTW: We're not using voice over IP). The routers have a WAN-T1 connection, DSX-1 and DBU connection)+ETH 0/1

T1/FT1 DSX-1 Network Interface Module (NIM)
No Dial Backup Interface Module (DIM) Selected

------------------------------------------------------------
Unit Mode
------------------------------------------------------------
Mode:
1) Routing
2) Bridging
------------------------------------------------------------Admin
------------------------------------------------------------

Router Name: BILLCLINTON

Enable Password: HILLARYCLINTON

Use this password as the Telnet password

Note: Telnet Password is One word only. Spaces are not allowed.

Telnet Password: HILLARYCLINTON
------------------------------------------------------------
Router
-----------------------------------------------------------
Default Route: (Enter IP Address)
. . .
Enable RIP?:
1) No
2) Yes Note: Selecting Yes will enable RIP on all interfaces.

Version: * (If Yes is selected for Enable RIP we have the option to
choose v1 or v2)
1) V1
2) V2

Generic NAT?:
1) No
2) Yes Note: Selecting Yes will enable the Firewall and create a
Many-to-One NAT on the WAN Interface.

-----------------------------------------------------------
LAN
------------------------------------------------------------
IP Address: (Enter IP Address)
. . .
Subnet Mask: (Enter Subnet Mask)
. . .
-----------------------------------------------------------
LAN IP Address (Validation is a click button) Optional

Network Address:
. . .
Broadcast Address:
. . .
Node Address:
. . .

------------------------------------------------------------
DHCP Options *(We are planning to setup a DHCP)

Note: Configures a DHCP Server for the Ethernet Attached LAN. The
Default is set to None.

DHCP Mode
1) None
2) Server

DHCP Domain Name


Primary DNS Server
. . .

Secondary DNS Server
Note: Optional
. . .

Lease time
Note: The default is a one-day lease.

Day (s) Hour (s) Minute (s)

Default Router
Note: IP Address of the default router for a DHCP client.
Use LAN IP address as default router.
. . .

------------------------------------------------------------
T1/FT1 DSX-1 NIM
------------------------------------------------------------

Line Coding
1) B8ZS
2) AMI

Framing
1) ESF
2) D4

Clock Source
1) Line (Recover from Line)
2) Internal (Use Internal Clock Src)
3) Through (Recover from DSX)

Data Timeslots
(The DS0s on the T1 that contain data for this router. i.e. 1-24 or
1,3,7,9 or 1-8,10,12)
------------------------------------------------------------
DSX-1
------------------------------------------------------------
Line Coding
1) B8ZS
2) AMI

Framing
1) ESF
2) D4

Signaling Mode
1) Robbed Bit (Robbed bit signaling on all DSOs)
2) Message Oriented (Clear Channel Signaling on Channel 24 only)
3) None (Clear Channel Signaling on all DSOs)
------------------------------------------------------------
WAN Protocol
------------------------------------------------------------
1) PPP
2) Frame Relay

Authentication Protocol
1) None
2) CHAP
3) PAP

User Name

Password

Numbered Interface
1) No
2) Yes

IP Address:
. . .
Subnet Mask:
. . .