MultiTech MVP-130 on IPO

[IPhello]

Refering back to this thread, thread940-1361610.
I have a question with the MVP-130. I know this is to be used for the communications manager only.
The scenario is as follows:
IP500 on one end tied together with a point to point T-1. I am running all IP sets at the remote end and they want to move their fax over there as well.
Is there a way to possibly use 2 of the MVP-130's, one at each end, and use an analog port out of the IP500 into one then route between the 2?

 

[hbsurfn]

I have done this before. One of the MVP-130's has to be an FXO and the other an FXS. I connected one MVP to my IP 500 via an analog port, connected the MVP to the network (Cox Cable P2P), on the other site connected MVP to the network and plugged in the fax machine. If you call Multi-Tech support, they will help you configure the MVP's on both sides.

 

[Bas1234]

You could try AudioCodes, MP11x series are great, they can do SIP with t38 and also H323.

___________________________________________
It works! Now if only I could remember what I did...
___________________________________________

 

[kwing112000]

We have used these as well and worked great. one on each end.

Kevin Wing
ACA- Implement IP Office
Carousel Industries

 

[IPhello]

I actually have it talking to the IPO now and this is what I get. when making a call. If you notice at the bottom it is saying no license for Ext711. Also when I present a call to it I get the same response. I think I will order the 3rd party end point license and see if I can get it to talk that way. You can see in the first log where it is confirming registration with the IPO.

1612208mS H323Evt: Recv: RegistrationRequest 0a000031; Endpoints registered: 1; Endpoints in registration: 0
1612209mS RasTx: v=Src=10.0.0.254:1719, Dst=10.0.0.49:16002 peb=0
RasMessage = registrationConfirm



231068mS H323Rx: src=10.0.0.49:1720
H323 Pcol=08(Q931) Reflen=2 ref=7908(Remote)
Message Type = Setup
1231069mS H323Evt: Didn't find extension by name MultiVoIP
1231069mS H323Evt: Found extn using ipaddr
1231069mS H323Evt: v=0 stacknum=250 State, new=NullState, old=NullState id=-1
1231070mS H323Evt: v=0 stacknum=250 State, new=Present, old=NullState id=4
1231070mS H245Rx: v=0 peb=250
MultimediaSystemControlMessage = request = terminalCapabilitySet

1231072mS H245Tx: v=0 peb=250
MultimediaSystemControlMessage = response = terminalCapabilitySetAck

1231072mS H323Tx: dst=10.0.0.49:1720
H323 Pcol=08(Q931) Reflen=2 ref=7908(Local)
Message Type = Facility
1231073mS H245Rx: v=0 peb=250
MultimediaSystemControlMessage = request = masterSlaveDetermination

1231075mS H323Evt: No licence for Ext711. Call rejected.

 

[amriddle01]

Does look like you need the third party end point licence, if it's on 4.2 system status will confirm this.

ACS - IP Office Implement

 

[tlpeter]

Or use two of them

Analog in an h323 out (analog port on ip0)
H323 in and analog out (to the fax)

ACA - Implement IP Office
ACS - Implement IP Office
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!