Modem advice required for USR 56K faxmodem in UK

[mabery]

I am trying to connect US Robotics 56k Faxmodem to Opt 11.
This modem does not have any dip switches and I am using Hyperterminal to connect. Trying to use the AT commands one at a time, this is what I get on my PC. Please note that I am in the UK, so it may be that the at&b1 command is not recognised, but I still need to know what that line should be.

at&f0 I get OK

ats0=1 I get OK

at&b1 I get ERROR

aty0 I get ERROR

atq1 No response ?

at&w0 No response ?

at&w1 No respose.

And when I do AT&V

the response is :-

E1 L2 M1 P¦T0
Q1 V1 X4 &C1
&D2 &G0 &I12
&P0 &R1 &S0
%B0 %C1
%D0 %L0 \G0 \K1
\N7 \Q3\ \T0 \V3
*BA5 *BO5 *DD3 *LS2 *MM18 +FCLASS=0
+FDD=0 +FL0=0 +FPR=0 +VCID=0 +VDR,1=0 +VDR,2=0

S00:001 S001:000 S002:43 S003:013 S004:010 S005:008
S006:002 S007:060 S008:002 S010:014 S011:080 S012:050
S018:000 S025:005 S026:000 S034:006 S075:056 S076:001
S077:090

Any assistance would be appreciated as I need to get this set up to allow me work remotely and not have to drive to the site..........

 

[geirendre]

Have you checked firebirdscrambler's FAQ on this?

http://www.tek-tips.com/faqs.cfm?fid=5043

 

[mabery]

Yes, and I have checked almost every posting on 'modems' that is on the site. I have tried to 'send' almost every command that has been posted to this modem and I get 'ERROR' on most.

 

[geirendre]

What function in the modem are you looking to enable/disable?
Do you have the "User manual"?

 

[johnpoole]

at&v ?

john poole
bellsouth business
columbia,sc

 

[bignose21]

I am i UK and this is the setup we use:


U.S. Robotics 56K FAX EXT Settings...

B0 E0 F1 L2 M1 Q1 V1 X3 Y0
SPEED=9600 PARITY=N WORDLEN=8
DIAL=TONE OFF LINE CID=0

&A3 &B1 &C1 &D0 &H2 &I2 &K0
&M4 &N0 &P0 &R1 &S0 &T5 &U0 &Y0

S00=001 S01=000 S02=043 S03=013 S04=010 S05=008 S06=004
S07=060 S08=002 S09=006 S10=014 S11=072 S12=050 S13=000
S15=000 S16=000 S18=000 S19=000 S21=010 S22=017 S23=019
S25=005 S27=001 S28=008 S29=020 S30=000 S31=128 S32=002
S33=000 S34=000 S35=000 S36=014 S38=000 S39=012 S40=000
S41=004 S42=000

 

[johnpoole]

i didn't see this untill i was home for the weekend so i can't compare it to an external modem

OK
at&v
ACTIVE PROFILE:
E1 L1 M1 Q0 T V1 X4 &C1 &D2 &G0 &P0
S00:000 S01:000 S02:043 S03:013 S04:010 S05:008 S06:002 S07:060 S08:002
S10:014 S12:050 S29:070

other then auto answer we are setup about the same.. your config should work.. have you tested the port? your good from the pc/term to the robotics.. what port and what type switch? port 0 on an 11 can be a pain.. i've needed an ini to wake that one up... can you print the adan? and or stat from ld 37..

modems can be strange, i use a breakout box when i get a stuborn one.. i also usually keep a normal and a rolled cable or at least a nul to put in line.. i hate dyper-term but it usually works... if you can short 2 to 3 on the rs232 you should be able to type and see it on the screen if dtr is shorted back to rts..


1
2 transmit
3 rec
4 to remote 5 or loop to local 5
5 to remote 4 or loop to local 4
6 to local 7
7 to remote 20 or loop back to local 20..

... if you wire that and you can even short local 4 to 5 on both ends.. if so the only 2 leads you really need are the transmit and rec..
8


john poole
bellsouth business
columbia,sc