Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
MICS 3.0 XC T1?
- Thread starter jsaad
- Start date
You can but........... 3.0 XC just barely meets the minimum requirements for T1. I know your customer is looking at cost more than anything else. Unfortuneatly 3.0 thru 6.0 have had problems with "Hung lines" which is the bigest problem with DID's in Disconnect Supervision without upgrading to at least 6.1
Alot too depends on your CO/dial tone provider.
Wish you could talk them into maybe a Fractional PRI and go with a refirbed DT1 and Combo card, and 6.1 It might save them money in the long run and you going postal on the MICS.
Alot too depends on your CO/dial tone provider.
Wish you could talk them into maybe a Fractional PRI and go with a refirbed DT1 and Combo card, and 6.1 It might save them money in the long run and you going postal on the MICS.
MICS 3.0 WI 5.10 & MICS 3.0 WI 5.11 should have correctd the T1.
In some installations of Norstar systems with MICS 3.0 software (XC and non XC), the customer may experience a system reset. This condition was seen only on systems that used TI E&M auto answer trunks with high traffic. In this scenario, the high traffic on the T1 E&M auto answer trunks caused software resources to be used up causing the system to reset.
With MICS 3.0 WI 5.10, the resources associated with the T1 E&M auto answer are reallocated preventing the system from resetting.
In some installations of Norstar systems with MICS 3.0 software (XC and non XC), the customer may experience a system reset. This condition was seen only on systems that used TI E&M auto answer trunks with high traffic. In this scenario, the high traffic on the T1 E&M auto answer trunks caused software resources to be used up causing the system to reset.
With MICS 3.0 WI 5.10, the resources associated with the T1 E&M auto answer are reallocated preventing the system from resetting.
- Thread starter
- #4
The first T1 I installed on a Norstar was back in the 90's when I was working at Atlantel. Our MICS had R1.1 software and a plain old T1 circuit worked fine. R3.0 should be good.
Brian Cox
Oregon Phone
Brian Cox
Oregon Phone
- Thread starter
- #6
curlycord
Programmer
Hence its name ... R1T1
Check that the carrier still provides T1's and not just PRI.
If low traffic and only 15 users why even speak of T1 or PRI?
Whats is wrong with current setup?
=----(((((((((()----=
curlycord
Check that the carrier still provides T1's and not just PRI.
If low traffic and only 15 users why even speak of T1 or PRI?
Whats is wrong with current setup?
=----(((((((((()----=
curlycord
- Thread starter
- #8
the cableco offers a bundle of super high speed internet with a T1 and DIDs. all over a cable tv cable. The price is super competitive and the customer wants it. most likely they are going to save a few hundred a month!
i believe if I upgrade the KSU, I might have to upgrade the flash vm, which if I recall is 1.9 or 1.44.
i'm throwing my hands up saying, why not upgrade? but they want to keep their system.
i believe if I upgrade the KSU, I might have to upgrade the flash vm, which if I recall is 1.9 or 1.44.
i'm throwing my hands up saying, why not upgrade? but they want to keep their system.
If you can only get PRI you'll have to upgrade the MICS to at least R4.0, but I'd recommend at least R6.1 MR.
If the voicemail is V1.9 you're OK, but V2.1 added routes for call transfers and remote notification. If it's V1.44 you'd need to upgrade.
Brian Cox
Oregon Phone
If the voicemail is V1.9 you're OK, but V2.1 added routes for call transfers and remote notification. If it's V1.44 you'd need to upgrade.
Brian Cox
Oregon Phone
- Status
Similar threads
- Locked
- Question
- Locked
- Question