Does anyone know how to status the D channel for the PRI with WinSPM? I have statused trunk 0124 which is the slot my DS1 card is in, but the status of the 24th port shows maintenance busy. Am I doing this correctly? Problem is I can't select a line when I dial 9 to go out and incoming calls do not come in. I have tried to verify several times that the PRI is properly programmed . I can't even hit the pool button assigned for these trunks to get out. Was working fine and now it doesn't. Of course local CO tests with Tbird and everything is fine. I think the D channel is down.
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Merlin Legend PRI
- Thread starter Revitt01
- Start date
You have a T1 card in slot 1? Wild idea. Much better to have a extension card in slot 1. But I digress. You should look at the light on the t1 card. What color is it?
Maintenance mode has a protected password. No one here will give that to you. Fess up. Do you know what you are doing?
Maintenance mode has a protected password. No one here will give that to you. Fess up. Do you know what you are doing?
- Thread starter
- #3
Well, thanks for the help. First of all, a close technician and friend installed this equipment and did the cut on Friday. The technician died of a heart attack on Monday. I was sent to troubleshoot. Yes to answer your question I know what I am doing. There are no lights on the DS1 card.
Probably too much information.
Since you know what you are doing you should start by printing and posting the error log and the PRI setup. Others here may take a stab at it like suggest that you busy and restore the slot or properly power cycle the system. Either of those may work for you but I would want to see the prints and know the history. You know...like it worked then what event happend on site to cause it not to work. Power outage etc... you know the usual.
Since you know what you are doing you should start by printing and posting the error log and the PRI setup. Others here may take a stab at it like suggest that you busy and restore the slot or properly power cycle the system. Either of those may work for you but I would want to see the prints and know the history. You know...like it worked then what event happend on site to cause it not to work. Power outage etc... you know the usual.
- Thread starter
- #5
Back at it today. The system worked fine until Friday. The cust had a number 864-338-8368 that would ring and no one would answer, so I added a route plan for it to look for 368, delete 3 digits, add 231 which is the operator. We called the number to check and it was answered by the operator, so I thought everything was fine. About 10 minutes later you could not make outgoing calls and incoming would get a message that says " Due to network difficulties your call cannot be completed at this time"
Here is the PRI info
PRI INFORMATION
A Slot 1 Switch: DMS-100
A System: By line
A BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
A 1 1 DMS-TieTrk By Dial Plan
A Channel ID: 9 8 7 6 5 4 3 2 1
A Line PhoneNumber NumberToSend
A 801 8643387737 8643387737
A 802
A 803
A 804
A 805
A 806
A 807
A 808
A 809
A Network Selection Table
A Entry Number: 0 1 2 3
A Pattern to Match: 101**** 10***
A Special Service Table
A Entry Number: 0 1 2 3 4 5 6 7
A Pattern to Match: 011 010 01 00 0 1
A Operator: none none none none none none none none
A Type of Number: I I I N N N N N
A Digits to Delete: 0 0 0 0 0 1 0 0
A Call-By-Call Service Table
A Entry Number: 0 1 2 3 4
A Call Type: BOTH BOTH BOTH BOTH BOTH
A NtwkServ:
A DeleteDigits: 0 0 0 0 0
A Entry Number: 5 6 7 8 9
A Call Type: BOTH BOTH BOTH BOTH BOTH
A NtwkServ:
A DeleteDigits: 0 0 0 0 0
A Dial Plan Routing Table
A Entry Number: 0 1 2 3
A NtwkServ: Any service Any service
A Expected Digits: 3 0 0 0
A Pattern to Match: 737
A Digits to Delete: 3 0 0 0
A Digits to Add: 231
A Entry Number: 4 5 6 7
A PRI INFORMATION
A NtwkServ: Any service
A Expected Digits: 0 3 0 0
A Pattern to Match: 279
A Digits to Delete: 0 3 0 0
A Digits to Add: 0
A Entry Number: 8 9 10 11
A NtwkServ:
A Expected Digits: 0 0 0 0
A Pattern to Match:
A Digits to Delete: 0 0 0 0
A Digits to Add:
A Entry Number: 12 13 14 15
A NtwkServ: Any service Any service
A Expected Digits: 0 0 3 3
A Pattern to Match: 368
A Digits to Delete: 0 0 3 0
A Digits to Add: 231
P3F1FIM Tone N $!Print !(Engli!sh )!: >N $!Make a! selec!tion ! N
Here is the PRI info
PRI INFORMATION
A Slot 1 Switch: DMS-100
A System: By line
A BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
A 1 1 DMS-TieTrk By Dial Plan
A Channel ID: 9 8 7 6 5 4 3 2 1
A Line PhoneNumber NumberToSend
A 801 8643387737 8643387737
A 802
A 803
A 804
A 805
A 806
A 807
A 808
A 809
A Network Selection Table
A Entry Number: 0 1 2 3
A Pattern to Match: 101**** 10***
A Special Service Table
A Entry Number: 0 1 2 3 4 5 6 7
A Pattern to Match: 011 010 01 00 0 1
A Operator: none none none none none none none none
A Type of Number: I I I N N N N N
A Digits to Delete: 0 0 0 0 0 1 0 0
A Call-By-Call Service Table
A Entry Number: 0 1 2 3 4
A Call Type: BOTH BOTH BOTH BOTH BOTH
A NtwkServ:
A DeleteDigits: 0 0 0 0 0
A Entry Number: 5 6 7 8 9
A Call Type: BOTH BOTH BOTH BOTH BOTH
A NtwkServ:
A DeleteDigits: 0 0 0 0 0
A Dial Plan Routing Table
A Entry Number: 0 1 2 3
A NtwkServ: Any service Any service
A Expected Digits: 3 0 0 0
A Pattern to Match: 737
A Digits to Delete: 3 0 0 0
A Digits to Add: 231
A Entry Number: 4 5 6 7
A PRI INFORMATION
A NtwkServ: Any service
A Expected Digits: 0 3 0 0
A Pattern to Match: 279
A Digits to Delete: 0 3 0 0
A Digits to Add: 0
A Entry Number: 8 9 10 11
A NtwkServ:
A Expected Digits: 0 0 0 0
A Pattern to Match:
A Digits to Delete: 0 0 0 0
A Digits to Add:
A Entry Number: 12 13 14 15
A NtwkServ: Any service Any service
A Expected Digits: 0 0 3 3
A Pattern to Match: 368
A Digits to Delete: 0 0 3 0
A Digits to Add: 231
P3F1FIM Tone N $!Print !(Engli!sh )!: >N $!Make a! selec!tion ! N
Your print messed up the post some how.
In your B Channel Group the Network Service needs to be CALL-BY-CALL not DMS-TieTrk, that won't work. Also some other stuff is missing from the print of the PRI.
Make sure line 824 the DCH is NOT in ANY pool or assigned in any way, that can cause the PRI not to work!
....JIM....
In your B Channel Group the Network Service needs to be CALL-BY-CALL not DMS-TieTrk, that won't work. Also some other stuff is missing from the print of the PRI.
Make sure line 824 the DCH is NOT in ANY pool or assigned in any way, that can cause the PRI not to work!
....JIM....
- Status
Similar threads
- Locked
- Question
- Locked
- Question
- Locked
- Question
- Locked
- Question